Hitachi EX100-3 EX100M-3 Excavator Operator Manual EM12S-NA1-3

Contents:
COVER
INDEX
CONTENTS
SAFETY
RECOGNIZE SAFETY INFORMATION
UNDERSTAND SIGNAL WORDS
FOLLOW SAFETY INSTRUCTIONS
WEAR PROTECTIVE CLOTHING
PROTECT AGAINST NOISE
PREPARE FOR EMERGENCIES
INSPECT MACHINE
USE HANDHOLDS AND STEPS
ADJUST THE SEAT
FASTEN YOUR SEAT BELT
OPERATE ONLY FROM OPERATOR’S SEAT
KEEP RIDERS OFF MACHINE
AVOID POWER LINES
AVOID INJURY FROM BACK-OVER AND SWING ACCIDENTS (SEE SA-004)
DIG WITH CAUTION
MOVE AND OPERATE MACHINE SAFELY
OPERATE MACHINE SAFELY
AVOID TIPPING
DRIVE MACHINE SAFELY
BEWARE OF EXHAUST FUMES
OPERATE WITH CAUTION
AVOID INJURY FROM RUNAWAY ACCIDENTS
PARK MACHINE SAFELY
HANDLE FLUIDS SAFELY – AVOID FIRES
PRACTICE SAFE MAINTENANCE
CLEAN TRASH FROM MACHINE
WARN OTHERS OF SERVICE WORK
CLEAN THE MACHINE REGULARLY
STORE ATTACHMENTS SAFELY
PREVENT BATTERY EXPLOSIONS
AVOID HARMFUL ASBESTOS DUST
PROTECT AGAINST FLYING DEBRIS
PREVENT PARTS FROM FLYING
STAY CLEAR OF MOVING PARTES
SUPPORT MACHINE PROPERLY
PREVENT BURNS
REMOVE PAINT BRFORE WELDIG OR HEATING
AVOID HEATING NEVER PRESSURIZED FLUID LINES
AVOID APPLYING HEAT TO LINES CONTAINING FLAMMABLE FLUIDS
AVOID HIGH-PRESSURE FLUIDS
PREVENT FIRES
HANDLE CHEMICAL PRODUCTS SAFELY
DISPOSE OF WASTE PROPERLY
SAFETY SIGNS
OPERATOR’S STATION
CAB FEATURES
MONITOR PANEL AND SWITCH PANELS
MONITOR PANEL AND SWITCH PANEL 1
KEY SWITCH
SWITCH PANEL 2
REAR CONSOLE
CAB HEATER
CAB HEATER AND AIR CONDITIONER (IF EQUIPPED)
LEFT CONSOLE
FM/AM RADIO OPERATION
TRAVEL ALARM CANCEL SWITCH
CAB DOOR RELEASE LEVER
CLOSING UPPER FRONT WINDOW
REMOVING AND STORING LOWER FRONT WINDOW
OPENING SIDE WINDOW
EMERGENCY EXIT
ADJUSTING THE SUSPENSION SEAT
SEAT BELT
DOME LIGHT
BREAK-IN
OBSERVE ENGINE OPERATION CLOSELY
EVERY EIGHT HOURS OR DAILY
AFTER THE FIRST 50 HOURS
AFTER THE FIRST 100 HOURS
PRE-START INSPECTION
INSPECT MACHINE DAILY BEFORE STARTING
OPERATING THE ENGINE
CHECK INSTRUMENTS BEFORE STARTING
LEVEL CHECK
STARTING THE ENGINE
STARTING IN COLD WEATHER
CHECK INSTRUMENTS AFTER STARTING
USING BOOSTER BATTERIES
STOPPING THE ENGINE
DRIVING THE MACHINE
DRIVING THE MACHINE
STEERING THE MACHINE USING PEDALS
STEERING THE MACHINE USING LEVERS
TRAVEL MODE SWITCHES
TRAVEL ALARM
PARKING THE MACHINE
LOCK ALL COMPARTMENTS
OPERATING THE MACHINE
CONTROL LEVER (ISO PATTERN)
ATTACHMENT PEDAL-IF EQUIPPED
OFFSET ARM FRONT -IF EQUIPPED
PILOT CONTROL SHUT-OFF LEVER
HYDRAULIC WARM-UP SWITCH
AUTO-IDLE SWITCH
POWER MODE (ENGINE SPEED)SELECTOR (E-P CONTROL)
WORK MODE SELECTOR
TRAVELING
OPERATING ON SOFT GROUND
RAISE ONE TRACK USING BOOM AND ARM
AVOID TIPPING
OPERATING IN WATER OR MUD
OPERATING BACKHOE
GRADING OPERATION
AVOID ABUSIVE OPERATION
OPERATING TIPS
SELECT CORRECT TRACK SHOES
FACE SHOVEL OPERATION
TOWING MACHINE A SHORT DISTANCE
LONG ARM OPERATION – IF EQUIPPED
ELECTRONIC CONTROL SYSTEM BYPASS PROCEDURE
PUMP SWASH ANGLE SETTING PROCEDURE
CRANING – IF EQUIPPED
ON USING THE RUBBER CRAWLER -IF EQUIPPED
ON USING THE RUBBER -COVERED GROUSER SHOES-IF EQUIPPED
OPERATING HYDRAULIC BREAKER-IF EQUIPPED
OPERATING HYDRAULIC CRUSHER -IF EQUIPPED
TRANSPORTING
TRANSPORTING BY ROAD
TRANSPORTING THE MACHINE BY TRAILER
PRECAUTIONS FOR TRANSPORTING MACHINES WITH RUBBER CRAWLER
PRECAUTIONS FOR TRANSPORTING MACHINES WITH RUBBER-COVERED SHOES
MAINTENANCE
CORRECT MACHINE AND INSPECTION PROCEDURES
SERVICE YOUR MACHINE AT SPECIFIED INTERVALS
CHECK THE HOUR METER REGULARLY
USE CORRECT FUELS AND LUBRICANTS
PREPARE MACHINE FOR MAINTENANCE
OPEN ACCESS DOORS FOR SERVICE
OPEN HOOD FOR SERVICE
PERIODIC REPLACEMENT OF PARTS
MAINTENANCE GUIGE
MAINTENANCE UNDER SPECIAL ENVIRONMENTAL CONDITIONS
STORAGE
STORING THE MACHINE
REMOVING THE MACHINE FROM STORAGE
INSTALLING VANDAL-PROOF COVERS
CRIME PREVENTION TIPS
HELP PREVENT CRIME
RECORD IDENIFICATION NUMBERS
KEEP PROOF OF OWNERSHIP
PARK INDOORS OUT OF SIGHT
WHEN PARKING OUTDOORS
REDUCE VANDALISM
REPORT THEFTS IMMEDIATELY
TROUBLESHOOTING
ENGINE
ELECTRICAL SYSTEM
MODE SELECTION
CONTROL LEVERS
HYDRAULIC SYSTEM
SPECIFICATIONS
SPECIFICATIONS (EX100-3)
WORKING RANGES (EX100-3)
WORKING RANGES (OFF-SET) (EX100-3)
WORKING RANGES (RUBBER CRAWLER) (EX100-3)
SHOE TYPES AND APPLICATIONS (EX100-3)
BUCKET TYPES AND APPLICATIONS (EX100-3)
SPECIFICATIONS (EX100M-3)
WORKING RANGES (EX100M-3)
WORKING RANGES (OFF-SET) (EX100M-3)
SHOE TYPES AND APPLICATIONS (EX100M-3)
BUCKET TYPES AND APPLICATIONS (EX100M-3)
MACHINE NUMBERS
MACHINE TYPE AND SERIAL NUMBER
ENGINE TYPE AND SERIAL NUMBER
TRAVEL MOTOR TYPE AND SERIAL NUMBER
SWING MOTOR TYPE AND SERIAL NUMBER
HYDRAULIC PUMP TYPE AND SERIAL NUMBER
INDEX