John Deere Timberjack Timbermatic 10 Measuring and Control System Operator Manual OMF069613
John Deere Timberjack Timbermatic 10 Measuring and Control System Operator Manual OMF069613 - Image 2
John Deere Timberjack Timbermatic 10 Operator Manual F069613 1

John Deere Timberjack Timbermatic 10 Measuring and Control System Operator Manual OMF069613

$30

  • Type Of Manual: Operator Manual
  • Manual ID: OMF069613
  • Format: PDF
  • Size: 4.2MB
  • Number of Pages: 200
Category: Tag:
Description
  • Model List:

    • Timberjack Timbermatic 10 Measuring and Control System
  • 1. Contents
  • 1.1. Introduction
  • 1.1.1. Introduction
  • 1.1.2. Standard warranty clauses
  • 1.1.3. Standard Warranty
  • 1.2. Safety instructions
  • 1.2.1. General
  • 1.2.2. Recognize safety information
  • 1.2.3. Understand signal words
  • 1.2.4. General safety rules
  • 1.2.5. Operating safety precautions
  • 1.3. Overview
  • 1.3.1. Description of Timbermatic 10 system
  • 1.3.2. Principles of length and diameter measurement
  • 1.3.3. Expressions
  • 1.3.4. Functions of programming wheel
  • 1.3.5. Functions of the soft key buttons
  • 1.4. User interface
  • 1.4.1. Displays symbols
  • 1.4.2. Help descriptions
  • 1.4.3. Window configuration
  • 1.4.4. Main window
  • 1.4.5. Preselections
  • 1.4.6. User interface
  • 1.4.7. Harvester head control buttons
  • 1.4.8. Left joystick
  • 1.4.9. Right joystick
  • 1.5. Operation
  • 1.5.1. Actions prior to operation
  • 1.5.2. Tree harvesting sequence
  • 1.5.3. Feeding sequence
  • 1.5.4. Searching of the cutting window
  • 1.5.5. Feed sequence for normal operation
  • 1.5.6. Feed sequence for searching cutting window
  • 1.5.7. Feed rollers and delimbing knives when feeding
  • 1.5.8. Adjusting feeding pressures
  • 1.5.9. Harvester head pressure
  • 1.5.10. Volume calculation (if diameter is in use)
  • 1.5.11. Stump treatment
  • 1.5.12. Automatic reversing when feeding is stuck
  • 1.5.13. Multitree handling
  • 1.6. Special situations
  • 1.6.1. Handling of a dropped tree
  • 1.6.2. Handling of a forked tree
  • 1.6.3. Handling of a tree lying on the ground
  • 1.7. Harvester head functions
  • 1.7.1. Upper delimbing knives open
  • 1.7.2. Upper delimbing knives close
  • 1.7.3. Knives open
  • 1.7.4. Feed roller arms open
  • 1.7.5. Feed roller arms close
  • 1.7.6. Rotate left
  • 1.7.7. Rotate right
  • 1.7.8. Feed forward
  • 1.7.9. Feed backward
  • 1.7.10. Low speed
  • 1.7.11. Stop on preselection
  • 1.7.12. Harvester head open
  • 1.7.13. Harvester head closed
  • 1.7.14. Tilt up/down
  • 1.7.15. Topping saw (option)
  • 1.7.16. Find end (option)
  • 1.7.17. MultiTree handling (option)
  • 1.8. Printing
  • 1.8.1. Printing window
  • 1.8.2. Parameters printout
  • 1.8.3. Millimetre printout
  • 1.8.4. Production printout
  • 1.9. Programming of preselections
  • 1.9.1. Information of the preselections
  • 1.9.2. Phases of programming the preselections
  • 1.9.3. Alternative preselection
  • 1.10. Settings
  • 1.10.1. General
  • 1.10.2. Adjustment of the settings
  • 1.10.3. Parameters
  • 1.11. Main settings window
  • 1.11.1. Content of settings window
  • 1.11.2. Tilt mode (T1)
  • 1.11.3. Tilt up delay (T2)
  • 1.11.4. Tilt currents (T3, T4)
  • 1.11.5. Tilt nudge distance (T5)
  • 1.11.6. Tilt diameter (T6)
  • 1.11.7. Tilt feed mode (T7)
  • 1.11.8. Automatic level of sawing (S1)
  • 1.11.9. Topping saw mode (S2)
  • 1.11.10. Saw delay (S3)
  • 1.11.11. Buttress (S4)
  • 1.11.12. Minimum pressure of feed roller arms during sawing (S5)
  • 1.11.13. Cut diameter limit (S6)
  • 1.11.14. Saw currents (S7, S8, S9)
  • 1.11.15. Topping saw offset (S10)
  • 1.11.16. Saw oiler (S11, S12)
  • 1.12. Feeding
  • 1.12.1. Feeding settings
  • 1.12.2. Feeding mode (F1)
  • 1.12.3. Feed ramp (F2)
  • 1.12.4. Braking distance (F3)
  • 1.12.5. Approach speed (F4)
  • 1.12.6. Overrunning distance (F5)
  • 1.12.7. Retraction distance after feeding is stuck (F6)
  • 1.12.8. Butt end reverse (F7)
  • 1.12.9. Dead stop distance control (F8)
  • 1.12.10. Delimbing knives pressure (F9)
  • 1.12.11. Feed roller arms pressure (F10)
  • 1.12.12. Diameter for delimbing knives pressure control (F11)
  • 1.12.13. Diameter for feed roller arms pressure control (F12)
  • 1.12.14. Knives open pulse length in feed backward (F13)
  • 1.12.15. Knives close pulse length in feed fwd (F15)
  • 1.12.16. Knives open pulse interval In feed backward (F14)
  • 1.12.17. Knives close pulse interval in feed fwd (F16)
  • 1.12.18. Length of opening pulse (F17)
  • 1.12.19. Feed rollers high pressure distance in feeding (F18)
  • 1.12.20. Slip prevention time (F19)
  • 1.12.21. Searching speed (F20)
  • 1.12.22. Searching trials (F21)
  • 1.12.23. Fast automatic speed (F22)
  • 1.12.24. Find end speed (F23)
  • 1.12.25. , 25 Feed currents forward (F24, F25 and F28, F29)
  • 1.12.26. , 27 Feed currents reverse (F26, F27 and F30, F31)
  • 1.12.27. Stop on preselection (F32)
  • 1.12.28. ,30 Expected dead stop distances (F33, F34)
  • 1.13. Multitree handling
  • 1.13.1. General
  • 1.13.2. Clamps on time (R3)
  • 1.13.3. Feed rollers open delay (R10)
  • 1.13.4. Feed rollers open duration (R11)
  • 1.14. Pump control
  • 1.14.1. Saw pumps (P1)
  • 1.14.2. Release time of pump 1 (P2) and pump 2 (P3)
  • 1.14.3. Proportional pump in use (P4)
  • 1.14.4. Control of proportional pump (P5 P9 )
  • 1.15. Service
  • 1.15.1. Statistics (X1)
  • 1.15.2. Diameter limit (X2)
  • 1.15.3. Factory settings (X7)
  • 1.15.4. Advance distance of the diameter measurement (X3)
  • 1.15.5. Find end offset (X4)
  • 1.15.6. Rotator currents (X5, X6)
  • 1.16. Calibration parameters
  • 1.16.1. Saw pulses (C1, C2)
  • 1.16.2. Quick diameter calibration (C3, C4)
  • 1.17. Module alarms
  • 1.17.1. Alarm settings window
  • 1.18. Versions
  • 1.18.1. Module program versions
  • 1.18.2. Lower delimbing knives (R1)
  • 1.18.3. Lower delimbing knives pressures (R4, R5)
  • 1.18.4. Feed roller arms pressures (R6, R7)
  • 1.18.5. Upper delimbing knives pressures (R8, R9)
  • 1.18.6. Feed roller arms close delay (R2)
  • 1.18.7. Clamps on time (R3)
  • 1.19. System control
  • 1.19.1. System control
  • 1.19.2. Automatic program update
  • 1.20. Diagnostics
  • 1.20.1. General
  • 1.21. Module I/O and harvester head test
  • 1.21.1. Module outputs and inputs
  • 1.22. Test windows
  • 1.22.1. Harvester head test
  • 1.22.2. Pump test
  • 1.23. Calibration
  • 1.23.1. Diameter range calibration
  • 1.23.2. Basic diameter calibration
  • 1.23.3. Length calibration
  • 1.23.4. Diameter curve (C5 C21)
  • 1.23.5. Text
  • 1.23.6. General
  • 1.23.7. Alarm log
  • 1.23.8. Active alarms
  • 1.24. General head parameters
  • 1.24.1. General
  • 1.24.2. Job number (G9)
  • 1.24.3. Head type (G10)
  • 1.24.4. Valve type (G11)
  • 1.24.5. Units (G12)
  • 1.24.6. General options
  • 1.24.7. Diameter in use (G13 )
  • 1.24.8. Measuring arm in use (G14)
  • 1.24.9. Stem counter (G15)
  • 1.24.10. Soft clamps (G16)
  • 1.24.11. Multitree handling (G17)
  • 1.24.12. Euca mode (G18)
  • 1.24.13. Preselection extension button (G19)
  • 1.25. Display settings
  • 1.25.1. Display settings
  • 1.26. Installation
  • 1.26.1. Installation instructions
  • 1.26.2. Welding precautions
  • 1.27. Parameter index
  • 1.27.1. Parameter index table
  • 1.28. Electrical schemes
  • 1.28.1. Timbermatic 10 Electric scheme
  • 2. Page Numbers
  • 2.1. Section 01
  • 2.2. Section 11
  • 2.3. Section 21
Rate this product

Related products

-50%
Mahindra Tractor 00 Series 4500 5500 6000 6500 Full Operator Manual Fast Download
Quick View

Mahindra

Mahindra Tractor 0 Series 2WD 4500 5500 6000 6500 Operator Manual

Original price was: $20.Current price is: $10.
Add to cart
Mahindra Tractor 16 Series 3616 Gear HST Full Parts Manual Fast Download
Quick View

Mahindra

Mahindra Tractor 16 Series 3616 Gear HST Parts Manual

$20
Add to cart
Mahindra Tractor 16 Series 3016 Gear HST Full Parts Manual Fast Download
Quick View

Mahindra

Mahindra Tractor 16 Series 3016 Gear HST Parts Manual

$20
Add to cart
-50%
Mahindra Tractor 16 Series 2516 Gear HST Full Operator Manual Fast Download
Quick View

Mahindra

Mahindra Tractor 16 Series 2516 Gear HST Operator Manual

Original price was: $20.Current price is: $10.
Add to cart
Mahindra Tractor 16 Series 3316 Gear HST Full Parts Manual Fast Download
Quick View

Mahindra

Mahindra Tractor 16 Series 3316 Gear HST Parts Manual

$20
Add to cart
-50%
Mahindra Tractor 10 Series 6110 Gear Cab Full Operator Manual Fast Download
Quick View

Mahindra

Mahindra Tractor 10 Series 6110 Gear Cab Operator Manual

Original price was: $20.Current price is: $10.
Add to cart
Mahindra Tractor 10 Series 4010 HST Full Parts Manual Fast Download
Quick View

Mahindra

Mahindra Tractor 10 Series 4010 HST Parts Manual

$20
Add to cart
-50%
Mahindra Tractor 15 Series 2015 4WD Full Operator Manual Fast Download
Quick View

Mahindra

Mahindra Tractor 15 Series 2015 4WD Operator Manual

Original price was: $20.Current price is: $10.
Add to cart