Description
-
Model List:
- ATJ 60 RC T4 S1
- 1. SAFETY PRECAUTIONS
- 1.1. GENERAL
- 1.1.1. FALL HAZARDS
- 1.1.2. ELECTROCUTION HAZARDS
- 1.1.3. TIPOVER HAZARDS
- 1.1.4. COLLISION AND CRUSHING HAZARDS
- 1.1.5. POISONING HAZARDS
- 1.1.6. INSPECTION AND MAINTENANCE HAZARDS
- 1.1.7. BATTERIES HAZARDS
- 2. INSTRUCTIONS
- 2.1. INSPECTIONS
- 2.1.1. GENERAL
- 2.1.2. WALKAROUND INSPECTION AND ROUTINE MAINTENANCE
- 2.1.2.1. INTRODUCTION
- 2.1.2.2. PROCEDURE
- 2.1.3. FUNCTION TESTS
- 2.1.3.1. INTRODUCTION
- 2.1.3.2. TEST THE GROUND CONTROLS AND THE ALARMS
- 2.1.3.3. TEST THE PLATFORM CONTROLS AND THE ALARMS
- 2.1.4. WORKPLACE INSPECTION
- 2.1.4.1. INTRODUCTION
- 2.1.4.2. PROCEDURE
- 2.2. COMPONENTS LOCATION
- 2.3. DECALS LOCATION USA
- 2.4. DECALS LOCATION CANADA
- 2.5. SAFETY COMPONENTS
- 2.5.1. SWING GATE AND SLIDING MIDRAIL
- 2.5.2. LANYARD ANCHORAGE POINTS
- 2.5.3. TURNTABLE LOCK PIN
- 2.6. MACHINE CONTROLS
- 2.6.1. GROUND CONTROLS PANEL AND GROUND SAFETY DEVICES
- 2.6.2. PLATFORM CONTROLS PANEL AND PLATFORM SAFETY DEVICES
- 2.6.3. LCD READOUT SCREEN PAGES
- 2.6.3.1. STARTUP PAGE
- 2.6.3.2. PREHEATING PAGE
- 2.6.3.3. ENGINE START PAGE
- 2.6.3.4. MENU PAGE
- 2.6.3.5. EDIT A SUB MENU
- 2.6.3.6. WORK PAGE
- 2.6.3.7. FAULT PAGE
- 2.6.3.8. WARNING PAGE
- 2.6.3.9. FAULT/WARNING CODE PAGE
- 2.6.3.10. MENUS/SUBMENUS
- 2.7. OPERATING INSTRUCTIONS
- 2.7.1. GENERAL
- 2.7.2. TRANSPORT/WORK POSITION
- 2.7.2.1. TRANSPORT POSITION
- 2.7.2.2. WORK POSITION
- 2.7.3. OPERATE FROM THE GROUND CONTROLS PANEL
- 2.7.3.1. POWER UP THE MACHINE
- 2.7.3.2. POWER DOWN THE MACHINE
- 2.7.3.3. START THE ENGINE
- 2.7.3.4. STOP THE ENGINE
- 2.7.3.5. POSITION THE PLATFORM
- 2.7.3.6. EMERGENCY STOP
- 2.7.4. OPERATE FROM THE PLATFORM CONTROLS PANEL
- 2.7.4.1. POWER UP AND POWER DOWN THE MACHINE
- 2.7.4.2. START THE ENGINE
- 2.7.4.3. STOP THE ENGINE
- 2.7.4.4. DRIVE, STEER AND BRAKE
- 2.7.4.5. POSITION THE PLATFORM
- 2.7.4.6. EMERGENCY STOP
- 2.7.5. SIMULTANEOUS FUNCTIONS
- 2.7.5.1. GROUND CONTROLS PANEL
- 2.7.5.2. PLATFORM CONTROLS PANEL
- 2.7.6. DRIVING ON A SLOPE
- 2.7.6.1. MEASURE THE SLOPE GRADE
- 2.7.7. LOCKED FUNCTIONS
- 2.7.7.1. TRANSPORT POSITION
- 2.7.7.2. WORK POSITION
- 2.7.8. RESCUE CONTROLS
- 2.7.8.1. IF THE ENGINE IS FUNCTIONAL
- 2.7.8.2. IF THE ENGINE IS NOT FUNCTIONAL
- 2.7.9. STANDARD EQUIPMENT
- 2.7.9.1. FRONT OSCILLATING AXLE
- 2.7.9.2. BATTERY MASTER SWITCH
- 2.7.9.3. DOUBLE 110 V ELECTRICAL OUTLET IN THE PLATFORM
- 2.7.9.4. BLOCK HEATER
- 2.7.10. OPTIONS
- 2.7.10.1. BATTERY HEATER
- 2.7.10.2. HYDRAULIC OIL HEATER
- 2.7.10.3. V GENERATOR
- 2.7.10.4. WORK LIGHT
- 2.7.10.5. SECONDARY GUARDING SYSTEM SAFEMANSYSTEM
- 2.8. PARKING AND STORAGE
- 2.9. TRANSPORTATION AND LIFTING
- 2.9.1. GENERAL
- 2.9.2. TRANSPORTATION INSTRUCTIONS
- 2.9.2.1. LOAD AND UNLOAD THE MACHINE
- 2.9.2.2. SET THE MACHINE FOR TRANSPORTATION
- 2.9.2.3. TIE DOWN THE MACHINE
- 2.9.2.4. TURNTABLE LOCK PIN
- 2.9.2.5. FREEWHEEL CONFIGURATION FOR WINCHING
- 2.9.3. LIFTING INSTRUCTIONS
- 2.10. CHARACTERISTICS
- 2.11. DIMENSIONS AND RANGE OF MOTION CHART
- 3. MAINTENANCE
- 3.1. GENERAL
- 3.2. PERIODIC MAINTENANCE
- 3.3. COMMISSIONING MAINTENANCE
- 3.4. MANDATORY MAINTENANCE FIRST 500 HOURS OR FIRST 6 MONTHS
- 3.5. SCHEDULED MAINTENANCE
- 3.6. OCCASIONAL MAINTENANCE AND OCCASIONAL OPERATION
- 3.7. FILTER ELEMENTS AND BELTS
- 3.8. LUBRICANTS, COOLANT AND FUEL
- 3.9. Ü ROUTINE MAINTENANCE
- 3.10. Ü EVERY 50 OPERATING HOURS OR EVERY MONTH
- 3.11. Ü EVERY 250 OPERATING HOURS OR EVERY 6 MONTHS
- 3.12. Ü EVERY 500 OPERATING HOURS OR EVERY YEAR
- 3.13. Ü EVERY 1000 OPERATING HOURS OR EVERY 2 YEARS
- 3.14. Ü EVERY 2000 OPERATING HOURS OR EVERY 4 YEARS
- 3.15. Ü OCCASIONAL MAINTENANCE
- 3.16. Ü OCCASIONAL OPERATION
