Description
-
Model List:
- 200 Series Cutting Platform
- 1. Contents
- 1.1. Safety Instructions and Safety Signs
- 1.1.1. Recognize Safety Information
- 1.1.2. Follow Safety Instructions
- 1.1.3. Understand Signal Words
- 1.1.4. Prepare for Emergencies
- 1.1.5. Wear Protective Clothing
- 1.1.6. Transport Combine with Header Safely
- 1.1.7. Decommissioning Proper Recycling and Disposal of Fluids and Components
- 1.1.8. Acquire Safety Knowledge and Information
- 1.1.9. Handle Agricultural Chemicals Safely
- 1.1.10. Do Not Get Close to the Header
- 1.1.11. Keep Hands Away from Blades
- 1.1.12. Use Safety Lights and Devices
- 1.1.13. Service Machines Safely
- 1.1.14. Service Drive Belts Safely
- 1.1.15. Practice Safe Maintenance
- 1.1.16. Avoid Heating Near Pressurized Fluid Lines
- 1.1.17. Service Accumulator Systems Safely
- 1.1.18. Remove Paint Before Welding or Heating
- 1.1.19. Avoid HighPressure Fluids
- 1.1.20. Road Safety Rules
- 1.1.21. Proper Load of Front and Rear Axles
- 1.1.22. Support Machine Properly
- 1.1.23. Install All Guards
- 1.1.24. Running of Combine and Header
- 1.1.25. Retighten Nuts of Front and Rear Wheels
- 1.1.26. Use Proper Tools
- 1.1.27. Store Attachments Safely
- 1.1.28. Safety Signs
- 1.2. Cutting Platform Coupling and Uncoupling
- 1.2.1. Header Coupling
- 1.2.2. Feeder House Safety Stop
- 1.2.3. Header Driveshaft
- 1.2.4. Coupling Hydraulic Lines
- 1.2.5. Reel Speed Motor
- 1.2.6. Horizontal Adjustment of Header
- 1.2.7. Header Uncoupling
- 1.2.8. Coupling of Header and Trailer
- 1.3. Cutting Platform Theory of Operation
- 1.3.1. Cutting Platform Theory of Operation
- 1.4. Operation and Adjustment of Cutting Platform
- 1.4.1. Using and Adjusting Properly Per Agronomic and Crop Conditions
- 1.4.2. Harvest Soybean (Flex Cutting Platform)
- 1.4.3. Wheat, Oats, Corn (Rigid Cutting Platform and Flex Cutting Platform)
- 1.4.4. Rice and Barley (Rigid Cutting Platform and Flex Cutting Platform)
- 1.4.5. Reel Lift Cylinder Safety Stops
- 1.4.6. Eccentric Reel Level Adjustment
- 1.4.7. Adjust Angle of Eccentric Reel Fingers
- 1.4.8. Nylon Reel Fingers
- 1.4.9. Adjust Reel Arm Width
- 1.4.10. Reel Minimum Clearance Adjustment
- 1.4.11. Adjust Reel Lifting Cylinder Height FineTune
- 1.4.12. Synchronize the Reel Cylinders
- 1.4.13. Adjust Reel Speed
- 1.4.14. Speed Motor
- 1.4.15. Adjust Continuously Variable Disk
- 1.4.16. Cutterbar
- 1.4.17. Adjust Cutterbar of Rigid Header
- 1.4.18. Adjust Cutterbar of Flex Cutting Platform
- 1.4.19. Indicator (Flexible Header)
- 1.4.20. Adjust Indicator
- 1.4.21. Crop Divider
- 1.4.22. Fender (Optional)
- 1.4.23. Soybean (Cutting Platform) Loss
- 1.5. Lubrication and Maintenance
- 1.5.1. Lubrication and Maintenance Requirements
- 1.5.2. After Using 10 Hours
- 1.5.3. After End of Harvest Season
- 1.5.4. Preparation Before Start of Harvest Season
- 1.5.5. Lubrication Points
- 1.5.6. Oil of the Cutterbar Drive Case
- 1.5.7. Storage of Lubricating Grease
- 1.5.8. Hours Lubrication Points
- 1.5.9. Hours Lubrication Points
- 1.5.10. Hours Lubrication Points
- 1.6. Analysis and Troubleshooting of Failures
- 1.6.1. Failure Analysis
- 1.7. Storage
- 1.7.1. After the End of Harvest Season
- 1.7.2. Before Start of Harvest Season
- 1.8. Special Accessories
- 1.8.1. Auger Guard
- 1.8.2. Rubber Guard
- 1.8.3. Reel Speed Change Sprocket
- 1.8.4. Header Knife Speed Change Belt Pulley
- 1.8.5. Auger Speed Change Sprocket
- 1.8.6. Miscellaneous
- 1.9. Technical Parameters
- 1.9.1. Header Model, Cutting Width, Weight, and Compatible Model
- 1.9.2. Technical Parameters
- 1.9.3. Metric Bolt and Screw Torque Values
- 2. Page Number
- 2.1. Section 05
- 2.2. Section 10
- 2.3. Section 15
- 2.4. Section 20
- 2.5. Section 25
- 2.6. Section 30
- 2.7. Section 35
- 2.8. Section 40
- 2.9. Section 45
