John Deere 2210 Floating Hitch Field Cultivator Operator Manual OMN404575

Description

• Model List:
  • 2210 Floating Hitch Field Cultivator

• 1. Contents
• 1.0.1. Recognize Safety Information
• 1.0.2. Understand Signal Words
• 1.0.3. Follow Safety Instructions
• 1.0.4. Prepare for Emergencies
• 1.0.5. Wear Protective Clothing
• 1.0.6. Practice Safe Maintenance
• 1.0.7. Handle Electronic Components and Brackets Safely
• 1.0.8. Support Raised Equipment
• 1.0.9. Remove Paint Before Welding or Heating
• 1.0.10. Avoid Heating Near Pressurized Fluid Lines
• 1.0.11. Avoid HighPressure Fluids
• 1.0.12. Check Hydraulic Hoses
• 1.0.13. Inspect Lift Circuit Hoses
• 1.0.14. Store Attachments Safely
• 1.0.15. Service Tires Safely
• 1.0.16. Decommissioning Proper Recycling and Disposal of Fluids and Components
• 1.0.17. Handle Chemical Products Safely
• 1.0.18. Operate Safely
• 1.0.19. Use Safety Lights and Devices
• 1.0.20. Keep Riders Off Machine
• 1.0.21. Observe Maximum Transport Speed
• 1.0.22. Use a Signal Person
• 1.0.23. Use a Safety Chain
• 1.0.24. Tow Loads Safely
• 1.0.25. Avoid Overhead Power Lines
• 1.0.26. Prepare for Transport
• 1.0.27. Transport Safely
• 1.0.28. Implements in Train Transport
• 1.0.29. Transport LockUp Valve
• 1.0.30. Do Not Fold Wings Until Machine Is Fully Raised
• 1.0.31. Park Safely
• 1.1. Safety Signs
• 1.1.1. Replace Damaged or Missing Safety Signs
• 1.1.2. Main Frame
• 1.1.3. Inner Wing
• 1.1.4. Wing Plates
• 1.1.5. Safety SignsTransport Locks ACCUDEPTHACCUDEPTH is a trademark of Deere Company Only
• 1.1.6. Low Transport
• 1.1.7. Operators Manual Decal
• 1.1.8. Informational Decals
• 1.2. Safety Features
• 1.2.1. Safety Features
• 1.3. Preparing Tractor
• 1.3.1. Use Tractor Operators Manual
• 1.3.2. Determine Tractor Requirements
• 1.3.3. Drawbar Requirements
• 1.3.4. Raise And Lock 3Point Hitch
• 1.3.5. Position Tractor Drawbar
• 1.3.6. Preparing Hydraulic System
• 1.3.7. Use a Safety Chain
• 1.4. Preparing Machine
• 1.4.1. Drawbar Requirements
• 1.4.2. Check And Lubricate Machine
• 1.4.3. Check Tire PressureAll Tillage Machines
• 1.4.4. Check Wheel HardwareAll Tillage Machines
• 1.4.5. Tighten Hardware
• 1.4.6. Checking And Adjusting Frame Foreaft Level
• 1.4.7. Checking And Adjusting SidetoSide Level for Single Point Depth Control Machines
• 1.5. Attaching And Detaching
• 1.5.1. Attach Machine Safely
• 1.5.2. Making Proper Hose Connections
• 1.5.3. Raising and Lowering Rear Parking StandMachines With Heavy Harrow And Rolling Basket Attachment
• 1.5.4. Attaching Machine To Tractor
• 1.5.5. Attach Safety Chain to Tractor
• 1.5.6. Attaching Warning Light Plug
• 1.5.7. Checking WingFold Operation
• 1.5.8. Checking Wing Fold Operation5Section, 3.6 M (12 Ft) Main Frame ONLY
• 1.5.9. Checking Single Point Depth Control
• 1.5.10. Detaching Machine From Tractor
• 1.6. Transporting
• 1.6.1. Following Safe Transport Procedures
• 1.6.2. Attach Safety Chain to Tractor
• 1.6.3. Using Warning Lights
• 1.6.4. Keep Riders Off Machine
• 1.6.5. Engaging Transport LockUp Valve
• 1.6.6. Using Transport Cylinder LocksACCUDEPTH Machines Only
• 1.6.7. Positioning Drawbar
• 1.6.8. Positioning Rear Parking StandMachines With Heavy Harrow And Rolling Basket Attachment
• 1.6.9. Positioning Jack For Transport
• 1.6.10. Transporting Machine
• 1.6.11. Transport MachineContinued
• 1.7. Operating Machine
• 1.7.1. Keep Riders Off Machine
• 1.7.2. Follow Safe Operating Procedures
• 1.7.3. General Guidelines For Use
• 1.7.4. Tighten Hardware
• 1.7.5. Operators Manual Holder
• 1.7.6. Using Adjustment Wrench
• 1.7.7. Before Entering Field Guidelines
• 1.7.8. Preparing To Operate Machine In Field
• 1.7.9. Setting Single Point Depth Control
• 1.7.10. Harrow Adjustments
• 1.7.11. Adjusting 2Bar Coil Tine Harrow With Rolling Baskets
• 1.7.12. Adjusting 3 And 4Bar Coil Tine Harrow
• 1.7.13. Bar Spike Tooth Rolling BasketAdjusting Down Pressure and Transport Clearance
• 1.7.14. Adjusting Spike Tooth Harrow Angle
• 1.7.15. Adjusting SpikeTooth Harrow Height
• 1.7.16. Adjusting SpikeTooth Harrow Height
• 1.7.17. Operate Optional Rear Hitch
• 1.8. Lubrication And Maintenance
• 1.8.1. Lubricating And Maintaining Machine Safely
• 1.8.2. Alternative And Synthetic Lubricants
• 1.8.3. Lubricant Storage
• 1.8.4. Beginning And End Of Season
• 1.8.5. Lubrication Symbols
• 1.8.6. Lubrication Intervals
• 1.8.7. Lubricate Jack
• 1.8.8. Lubricate Wheel Bearings
• 1.8.9. Lubricate Caster Wheel Pivot Bearings
• 1.8.10. Lubricate Rear Swing Arm Pivots
• 1.8.11. Lubricate Foreaft Links
• 1.8.12. Lubricate Basket Bearings
• 1.8.13. Lubricate Rolling Basket Trunnions
• 1.8.14. Repack Walking Beam Pivot Bearings
• 1.9. Troubleshooting
• 1.9.1. Troubleshooting Machine
• 1.9.2. Troubleshooting PERMALOC Sweeps
• 1.9.3. Troubleshooting Drawbar Hitch Links
• 1.9.4. Recommendations For Working Hard Soils
• 1.9.5. Recommendation For Excessive Plugging
• 1.9.6. Recommendation For Excessive Plugging 4Bar
• 1.9.7. Troubleshooting Wing Folding Operation5Section, 3.6 M (12 Ft) Main Frame ONLY
• 1.10. Service
• 1.10.1. Practice Safe Maintenance
• 1.10.2. Use Safe Service Procedures
• 1.10.3. Work in Clean Area
• 1.10.4. Service Machines Safely
• 1.10.5. Illuminate Work Area Safely
• 1.10.6. Support Machine Properly
• 1.10.7. Keep Service Area Clean
• 1.10.8. Replacing Ground Engaging Tools
• 1.10.9. Tighten Hardware
• 1.10.10. Metric Bolt and Screw Torque Values
• 1.10.11. Unified Inch Bolt and Screw Torque Values
• 1.10.12. Face Seal Fittings Assembly and InstallationAll Pressure Applications
• 1.10.13. Metric Face Seal and ORing Stud End Fitting Torque ChartStandard Pressures
• 1.10.14. SAE Face Seal and ORing Stud End Fitting Torque ChartStandard Pressures
• 1.10.15. Discarded Tires
• 1.10.16. Service Tires Safely
• 1.10.17. Check Tire PressureAll Tillage Machines
• 1.10.18. Repair Tire
• 1.10.19. Check Wheel HardwareAll Tillage Machines
• 1.10.20. Disassemble Wheel Hub Assembly
• 1.10.21. Assembly Wheel Hub Assembly
• 1.10.22. Checking Cshank Assembly
• 1.10.23. Checking Standard Bushings
• 1.10.24. Replacing SplitTension Bushings
• 1.10.25. Replacing Worn PERMALOC Sweeps
• 1.10.26. Removing PERMALOC Sweeps
• 1.10.27. Attaching PERMALOC Sweeps
• 1.10.28. Modifying PERMALOC Sweeps
• 1.10.29. Attach PERMALOC CastingField Cultivator
• 1.10.30. Checking Depth Control Hydraulic System
• 1.10.31. Preventing Hydraulic System Contamination
• 1.10.32. Checking Depth Control for LeakageMachine Without Single Point Depth Control
• 1.10.33. Checking Depth Control for Leakage
• 1.10.34. Analyzing Test ResultsSeriesParallel System
• 1.10.35. Removing Hydraulic Cylinders
• 1.10.36. Before Bleeding Hydraulic SystemSingle Point Depth Control3.6 m (12 ft) Main Frame
• 1.10.37. Cleanliness
• 1.10.38. Bleed Hydraulic SystemSingle Point Depth Control3.6 m (12 ft) Main Frame
• 1.10.39. Before Bleeding Hydraulic SystemSingle Point Depth Control4.5 m (15 ft) Main Frame
• 1.10.40. Bleed Hydraulic SystemSingle Point Depth Control4.5 m (15 ft) Main Frame ONLY
• 1.10.41. Installing And Bleeding WingFold Cylinders
• 1.10.42. Hydraulic Hose Replacement
• 1.10.43. Replace Wheel Retraction Switch 3.6 m (12 ft) Main Frame ONLY
• 1.11. Storage
• 1.11.1. Preparing For Storage
• 1.11.2. Removing From Storage
• 1.12. Specifications
• 1.12.1. Hitch Specifications
• 1.12.2. Tractor Horsepower Recommendations
• 1.12.3. Section
• 1.12.4. Section
• 1.12.5. Download Force On Tractor Drawbar
• 1.12.6. Product Identification Number
• 1.12.7. Record Product Identification Number (P.I.N.)
• 1.12.8. Keep Proof of Ownership
• 1.12.9. Keep Machines Secure
• 1.13. John Deere Service Literature Available
• 1.13.1. Technical Information
• 1.14. John Deere Service Keeps You On the Job
• 1.14.1. John Deere Is At Your Service
• 2. Page Number
• 2.1. Section 05
• 2.2. Section 10
• 2.3. Section 15
• 2.4. Section 20
• 2.5. Section 25
• 2.6. Section 30
• 2.7. Section 35
• 2.8. Section 40
• 2.9. Section 45
• 2.10. Section 50
• 2.11. Section 55
• 2.12. Section 60
• 2.13. Section 65
• 2.14. Section JDServ
• 2.15. Section JDService