John Deere 2230 Floating Hitch Field Cultivator Operator Manual OMKK55222

Description

• Model List:
  • 2230 Floating Hitch Field Cultivator

• 1. Introduction
• 1.1. Foreword
• 1.2. Recognize Safety Information
• 1.3. Understand Signal Words
• 1.4. Follow Safety Instructions
• 1.5. Spanish Safety Signs and Operators Manual
• 1.6. Prepare for Emergencies
• 1.7. Wear Protective Clothing
• 1.8. Practice Safe Maintenance
• 1.9. Handle Electronic Components and Brackets Safely
• 1.10. Support Raised Equipment
• 1.11. Remove Paint Before Welding or Heating
• 1.12. Avoid Heating Near Pressurized Fluid Lines
• 1.13. Avoid HighPressure Fluids
• 1.14. Check Hydraulic Hoses
• 1.15. Inspect Lift Circuit Hoses
• 1.16. Store Attachments Safely
• 1.17. Service Tires Safely
• 1.18. Decommissioning Proper Recycling and Disposal of Fluids and Components
• 1.19. Handle Chemical Products Safely
• 1.20. Operate Safely
• 1.21. Use Safety Lights and Devices
• 1.22. Keep Riders Off Machine
• 1.23. Observe Maximum Transport Speed
• 1.24. Use a Signal Person
• 1.25. Use a Safety Chain
• 1.26. Tow Loads Safely
• 1.27. Avoid Overhead Power Lines
• 1.28. Prepare for Transport
• 1.29. Transport Safely
• 1.30. Implements in Train Transport
• 1.31. Transport Lockup Valve
• 1.32. Do Not Operate SCV I in Continuous with Wheel Retraction Valve
• 1.33. Do Not Fold Wings Until Machine Is Fully Raised
• 1.34. Park Safely
• 2. Safety Signs
• 2.1. Replace Damaged or Missing Safety Signs
• 2.2. Main Frame
• 2.3. Large 5Section Main Frame
• 2.4. Section Outer Wing
• 2.5. Cylinder Locks
• 2.6. Informational Decals
• 3. Safety Features
• 3.1. Safety Features
• 4. Preparing Tractor
• 4.1. Use Tractor Operators Manual
• 4.2. Determine Tractor Requirements
• 4.3. Drawbar Requirements
• 4.4. Secure ThreePoint Hitch
• 4.5. Power TakeOff
• 4.6. Position Drawbar
• 4.7. Prepare Hydraulic SystemJohn Deere R/RT Series Tractors
• 4.8. Use a Safety Chain
• 5. Preparing Machine
• 5.1. Drawbar Requirements
• 5.2. Check and Lubricate Machine
• 5.3. Check Tire PressureAll Tillage Machines
• 5.4. Check Wheel HardwareAll Tillage Machines
• 5.5. Tighten Hardware
• 5.6. Adjust FronttoRear Level
• 5.7. Adjust SidetoSide Level
• 6. Attaching and Detaching
• 6.1. Use Your Tractor and Tillage Equipment Operators Manuals
• 6.2. Before Attaching Machine to Tractor
• 6.3. Attach Machine to Tractor
• 6.4. Make Proper Hose Connections
• 6.5. Attach Electrical Connectors
• 6.6. Position Jack for Transport
• 6.7. Attach Safety Chain to Tractor
• 6.8. Engage Transport Lockup Valve
• 6.9. Check WingFold Operation
• 6.10. Check Single Point Depth Control
• 6.11. Raising and Lowering Rear Parking StandMachines With Rear Hitch
• 6.12. Detach Machine from Tractor
• 7. Transporting
• 7.1. Use Safety Lights and Devices
• 7.2. Observe Maximum Transport Speed
• 7.3. Use a Safety Chain
• 7.4. Attach Safety Chain to Tractor
• 7.5. Tow Loads Safely
• 7.6. Avoid Overhead Power Lines
• 7.7. Prepare for Transport
• 7.8. Close Transport Lockup Valve
• 7.9. Use Cylinder Locks
• 7.10. Light Enhancement Module
• 7.11. Keep Riders Off Machine
• 7.12. Position Drawbar
• 7.13. Position Jack for Transport
• 7.14. Transport Machine
• 8. Operating Machine
• 8.1. Keep Riders Off Machine
• 8.2. Follow Safe Operating Procedures
• 8.3. Guidelines for Use
• 8.4. Tighten Hardware
• 8.5. Use Operators Manual Holder
• 8.6. Use Adjustment Wrench
• 8.7. Prepare to Operate Machine in Field
• 8.8. Adjust Single Point Depth Control
• 8.9. Level Machine
• 8.10. Adjust Coil Tine Harrows
• 8.10.1. Adjust Spring Tension
• 8.10.2. Adjust Coil Tine Angle
• 8.11. Adjust Spike Tooth Harrows
• 8.11.1. Adjust Harrow Height and Draft
• 8.11.2. Adjust Harrow Spike Angle
• 8.12. Adjust Rolling Baskets
• 8.13. Understand Active Hydraulic Rolling Basket DownPressure System
• 8.14. Adjust Rolling Basket DownPressureTractors With ElectroHydraulic Closed Center Systems
• 8.15. Operate Optional Rear Hitch
• 9. Lubrication and Maintenance
• 9.1. Lubricating and Maintaining Machine Safely
• 9.2. Multipurpose Extreme Pressure (EP) Grease
• 9.3. Alternative and Synthetic Lubricants
• 9.4. Lubricant Storage
• 9.5. Beginning and End of Season
• 9.6. Lubrication Symbols
• 9.7. Lubrication Intervals
• 9.8. Lubricate Jack
• 9.9. Lubricate Wheel Bearings
• 9.10. Lubricate Caster Wheel Pivot Bearings
• 9.11. Lubricate Fore/Aft Links
• 9.12. Repack Walking Beam Pivot Bearings
• 10. Troubleshooting
• 10.1. Troubleshooting Machine
• 10.2. Troubleshooting PermaLoc Sweeps
• 10.3. Troubleshooting Drawbar Hitch Links
• 10.4. Troubleshoot 5Section Machine WingFold Operation
• 10.5. Recommendations for Working Hard Soils
• 10.6. Recommendation for Excessive Harrow Plugging
• 11. Service
• 11.1. Practice Safe Maintenance
• 11.2. Use Safe Service Procedures
• 11.3. Work in Clean Area
• 11.4. Service Machines Safely
• 11.5. Illuminate Work Area Safely
• 11.6. Support Machine Properly
• 11.7. Keep Service Area Clean
• 11.8. Replacing Ground Engaging Tools
• 11.9. Tighten Hardware
• 11.10. Metric Bolt and Screw Torque Values
• 11.11. Unified Inch Bolt and Screw Torque Values
• 11.12. Face Seal Fittings Assembly and InstallationAll Pressure Applications
• 11.12.1. Face Seal ORing to Stud End Installation
• 11.12.2. Face Seal Adjustable Stud End ORing Installation
• 11.12.3. Face Seal Straight Stud End ORing Installation
• 11.12.4. Fitting Installation
• 11.12.5. Assembly Torque
• 11.13. Metric Face Seal and ORing Stud End Fitting Torque ChartStandard Pressures
• 11.14. SAE Face Seal and ORing Stud End Fitting Torque ChartStandard Pressures
• 11.15. Discarded Tires
• 11.16. Service Tires Safely
• 11.17. Check Tire PressureAll Tillage Machines
• 11.18. Repair TireMain Frame
• 11.19. Check Wheel HardwareAll Tillage Machines
• 11.20. Service Walking BeamType 1
• 11.20.1. Disassemble and Inspect Walking Beam
• 11.20.2. Assemble Walking Beam
• 11.21. Service Walking BeamType 2
• 11.21.1. Disassemble and Inspect Walking Beam
• 11.21.2. Assemble Walking Beam
• 11.22. Inspect Depth Control Rockshaft Bearings
• 11.23. Replace Depth Control Bearings
• 11.24. Check CShank Assembly
• 11.25. Check Standard Bushings
• 11.26. Replace SplitTension Bushings
• 11.27. Replace Worn PermaLoc Sweeps
• 11.28. Remove PermaLoc Sweeps
• 11.29. Attach PermaLoc Sweeps
• 11.30. Attach PermaLoc Casting
• 11.31. Prevent Hydraulic System Contamination
• 11.32. Checking Single Point Depth Control for Leakage
• 11.33. Analyzing Test ResultsSeriesParallel System3Section Machines
• 11.34. Analyzing Test ResultsSeriesParallel System5Section Machines
• 11.35. Removing Hydraulic Cylinders
• 11.36. Before Bleeding Hydraulic System
• 11.37. Cleanliness
• 11.38. Bleed Hydraulic System All Machines
• 11.39. Bleed Optional Rolling Basket Hydraulic Cylinders
• 11.40. Replace Hydraulic Hoses
• 11.41. Replace Wheel Retraction Switch5Section Machines ONLY
• 11.42. Service Rolling Baskets
• 12. Storage
• 12.1. Preparing for Storage
• 12.2. Removing From Storage
• 13. Specifications
• 13.1. Hitch Specifications
• 13.2. Download Force on Tractor Drawbar
• 13.3. Tractor Power Recommendations
• 13.4. Machine Specifications
• 13.5. Tire Specifications
• 13.6. Standards and Sweeps Specifications
• 13.7. Hydraulic Hose Specifications
• 13.8. ProFinish Leveling SystemAttachment Specifications
• 13.9. Record Product Identification Number (PIN.)
• 13.10. Keep Proof of Ownership
• 13.11. Keep Machines Secure
• 14. John Deere Service Literature Available
• 14.1. Technical Information
• 15. John Deere Service Keeps You On The Job
• 15.1. John Deere Is At Your Service