Description
-
Model List:
- MH1006 Corn Header
- 1. Contents
- 1.1. Predelivery Inspection
- 1.1.1. Predelivery Inspection
- 1.1.2. Recognize Safety Information
- 1.1.3. Understand Signal Words
- 1.1.4. Follow Safety Instructions
- 1.1.5. Ballasting for Safe Ground Contact
- 1.1.6. Parking and Leaving the Machine
- 1.1.7. Prepare for Emergencies
- 1.1.8. Wear Protective Clothing
- 1.1.9. Stay Clear of Header
- 1.1.10. Use Safety Lights and Devices
- 1.1.11. Transport Combine With Header Safely
- 1.1.12. Practice Safe Maintenance
- 1.1.13. Remove Paint Before Welding or Heating
- 1.1.14. Avoid Heating Near Pressurized Fluid Lines
- 1.1.15. Avoid Entanglement
- 1.1.16. Avoid Contact With Moving Parts
- 1.1.17. Stay Clear of Rotating Drivelines
- 1.1.18. Guards and Shields
- 1.1.19. Avoid HighPressure Fluids
- 1.1.20. Service Machines Safely
- 1.1.21. Service Drive Belts Safely
- 1.1.22. Protect Against High Pressure Spray
- 1.1.23. Decommissioning Proper Recycling and Disposal of Fluids and Components
- 1.1.24. Support Machine Properly
- 1.1.25. Store Attachments Safely
- 1.2. Safety Signs
- 1.2.1. Safety Sign Locations
- 1.2.2. SMV Emblem
- 1.2.3. Replace Safety Signs
- 1.2.4. Rotating Drive Shaft Decal B
- 1.2.5. Auger Floor Cleanout Door Decal A
- 1.2.6. Do not Step in Header Unit and Keep Safe Distances.
- 1.3. Transporting
- 1.3.1. Transporting on Trailer
- 1.3.2. Trailer Hitch Combine
- 1.3.3. Transporting on Combine
- 1.4. Attaching and Detaching
- 1.4.1. Attaching Platform to Combine
- 1.4.2. Detaching Platform from Combine
- 1.5. Combine Preparation
- 1.5.1. Rear Axle Ballasting (Rear Main Body Frame Ballasting)
- 1.5.2. Rear Hood Ballasting
- 1.5.3. Install Cylinder Filler Plates
- 1.5.4. Prepare for Grain Tank
- 1.6. Operating the Corn Header
- 1.6.1. General Information
- 1.6.2. Drive and Operate Carefully
- 1.6.3. Corn Header Height Control
- 1.6.4. Corn Head Speed of Travel
- 1.6.5. Harvesting Corn With Weakened or Broken Stalks
- 1.6.6. Gatherers
- 1.6.7. Row Units
- 1.7. AdjustmentsCorn Head
- 1.7.1. Adjusting and Leveling Gatherer Points
- 1.7.2. Adjust Trash Knives
- 1.7.3. Adjust Gathering Chain Tension
- 1.7.4. Adjust Deck Plate
- 1.7.5. Adjusting Auger Height
- 1.7.6. Coupling the Chain
- 1.7.7. Adjusting Auger Drive Chain and Gear Drive Shaft Chain
- 1.7.8. Combine Setting Chart
- 1.8. Lubrication
- 1.8.1. Use Correct Lubricant
- 1.8.2. Lubricant Storage
- 1.8.3. Alternative and Synthetic Lubricants
- 1.8.4. Mixing of Lubricants
- 1.9. Lubrication and Maintenance
- 1.9.1. Lubrication and Maintenance Interval Chart
- 1.9.2. Lubrication Points Daily
- 1.9.3. Check Row Unit Gearbox Oil Level
- 1.10. Troubleshooting
- 1.10.1. Corn Head
- 1.11. Service
- 1.11.1. Opening Row Unit Cover
- 1.11.2. Remove and Install Gatherer Chain
- 1.11.3. Remove and Install Blades
- 1.12. Storage
- 1.12.1. End of Season Service
- 1.12.2. Beginning of Season Service
- 1.13. Specifications
- 1.13.1. Specifications
- 1.13.2. Keep Machines Secure
- 1.13.3. Header Identification Number
- 1.13.4. Keep Proof of Ownership
- 1.13.5. Unified Inch Bolt and Screw Torque Values
- 1.13.6. Metric Bolt and Screw Torque Values
- 1.14. John Deere Service Keeps You On The Job
- 1.14.1. John Deere Is At Your Service
- 2. Page Number
- 2.1. Section 0
- 2.2. Section 10
- 2.3. Section 15
- 2.4. Section 20
- 2.5. Section 25
- 2.6. Section 30
- 2.7. Section 35
- 2.8. Section 45
- 2.9. Section 50
- 2.10. Section 55
- 2.11. Section 60
- 2.12. Section 65
- 2.13. Section 70
- 2.14. Section 75
