Description
-
Model List:
- 600X Series Cutting Platform
- 1. Contents
- 1.0.1. Recognize Safety Information
- 1.0.2. Follow Safety Instructions
- 1.0.3. Observe Road Traffic Regulations
- 1.0.4. Use Safety Lights and Devices
- 1.0.5. Prepare for Emergencies
- 1.0.6. Wear Protective Clothing
- 1.0.7. Store Attachments Safely
- 1.0.8. Guards and Shields
- 1.0.9. Stay Clear of Harvesting Units
- 1.0.10. Keep Hands Away From Knives
- 1.0.11. Stay Clear of Rotating Drivelines
- 1.0.12. Stay Clear of Cutterbar When Rotating Auger
- 1.0.13. Ballasting for Safe Ground Contact
- 1.0.14. Practice Safe Maintenance
- 1.0.15. Service Machines Safely
- 1.0.16. Service Drive Belts Safely
- 1.0.17. Support Machine Properly
- 1.0.18. Protect Against Noise
- 1.0.19. Avoid Heating Near Pressurized Fluid Lines
- 1.0.20. Avoid HighPressure Fluids
- 1.0.21. Decommissioning Proper Recycling and Disposal of Fluids and Components
- 1.0.22. Road Transport Disconnect Button
- 1.0.23. Safety SignsTextFree
- 1.0.24. Safety SignsText
- 1.0.25. Replace Safety Signs
- 1.1. Field Operation
- 1.1.1. Cutting PlatformtoCombine Adaptation
- 1.1.2. Attach Cutting Platform
- 1.1.3. Cutting Platform Tilt Angle
- 1.1.4. Header Height Control Skid Plates
- 1.1.5. Detach Cutting Platform
- 1.1.6. Transport Cutting Platform on a Trailer
- 1.1.7. Cutting Platform Emergency Mode
- 1.1.8. Calibrate Cutting Platform
- 1.1.9. Cutterbar and Reel Safety Feature
- 1.1.10. Cutterbar and Reel Safety FeatureSelf Test
- 1.1.11. Engage Cutting Platform Drive
- 1.1.12. Operate the Cutting PlatformGeneral
- 1.1.13. Operate the Cutting PlatformCrop Condition Adaptation
- 1.1.14. Fine Knife (Option)
- 1.1.15. Crop Dividers (Option)
- 1.1.16. Rape Seed Knife (Option)
- 1.1.17. Lifting Guards (Option)
- 1.1.18. Knife Protection Guard (If Equipped)
- 1.1.19. Troubleshooting
- 1.1.20. Safety Stop for Feeder House Lift Cylinder
- 1.1.21. Set Safety Stop for Reel Lift Cylinder
- 1.1.22. Adjust Cutterbar Position
- 1.1.23. Adjust Reel Tine Pitch
- 1.1.24. Adjust Auger Height
- 1.1.25. Adjust Auger Fore/Aft
- 1.1.26. Adjust Auger Finger Timing
- 1.1.27. Adjust Rear Stripper
- 1.1.28. Adjust Floor Stripper
- 1.2. Lubrication and Maintenance
- 1.2.1. Required EmissionRelated Information
- 1.2.2. Safety Stop for Feeder House Lift Cylinder
- 1.2.3. Set Safety Stop for Reel Lift Cylinder
- 1.2.4. Side Shields
- 1.2.5. Tool Box (Option)
- 1.2.6. Gear Oil
- 1.2.7. Alternative and Synthetic Lubricants
- 1.2.8. Mixing of Lubricants
- 1.2.9. Lubricant Storage
- 1.2.10. Lubrication Chart
- 1.2.11. Main Drive Gear Case
- 1.2.12. Knife Drive Gear Case
- 1.2.13. Sealing Bridge Pivoting Mechanism
- 1.2.14. Cutterbar Table Sheet and Sealing Bridge
- 1.2.15. Header Height Control SensorsOnce a Year
- 1.2.16. Reel Basic Setting
- 1.2.17. Hydraulic Valve Blocks
- 1.2.18. Rephase Reel Fore/Aft Cylinders
- 1.2.19. Rephase Reel Lift Cylinders
- 1.2.20. Adjust Reel Speed Sensor
- 1.2.21. Adjust Knife Drive Belts Tension
- 1.2.22. Replace Knife Drive Belts
- 1.2.23. Replace Cutterbar Knife
- 1.2.24. Replace Cutterbar Wear Plates
- 1.2.25. Set Knife Timing (635X and 640X)
- 1.2.26. Align Knife Head and Knife Drive
- 1.2.27. Replace Knife Sections
- 1.2.28. Adjust Auger Drive Chain Tension
- 1.2.29. Replace Auger Fingers and Retainers
- 1.2.30. Replace Stubble Light Bulb (If Equipped)
- 1.2.31. End of Season
- 1.2.32. Beginning of Season Service
- 1.3. Specifications
- 1.3.1. 640X Cutting Platforms
- 1.3.2. Type Plates
- 1.3.3. Cutting Platform (Product Identification) Type Plate
- 1.3.4. Product Identification Number
- 1.3.5. Machine Component Serial Numbers
- 1.3.6. Metric Bolt and Screw Torque Values
- 1.3.7. Unified Inch Bolt and Screw Torque Values
- 1.3.8. Keep Machines Secure
- 1.3.9. Keep Proof of Ownership
- 1.3.10. EC Declaration of Conformity
- 1.3.11. Eurasian Economic Union
- 1.4. John Deere Service Literature Available
- 1.4.1. Technical Information
- 1.5. John Deere Service Keeps You On the Job
- 1.5.1. John Deere Parts
- 1.5.2. The Right Tools
- 1.5.3. WellTrained Technicians
- 1.5.4. Prompt Service
- 2. Page Number
- 2.1. Section 01
- 2.2. Section 02
- 2.3. Section 03
- 2.4. Section 04
- 2.5. Section JDSLA
