John Deere 625D, 630D, 635D Draper Flatforms Operator Manual OMH234643

Description

• Model List:
  • 625D Draper Flatform
  • 630D Draper Flatform
  • 635D Draper Flatform

• 1. Contents
• 1.0.1. Platform Safety Features
• 1.0.2. Safety Sign Location
• 1.0.3. Recognize Safety Information
• 1.0.4. Understand Signal Words
• 1.0.5. Use Safety Lights and Devices
• 1.0.6. Follow Safety Instructions
• 1.0.7. Spanish Safety Signs and Operators Manual
• 1.0.8. Wear Protective Clothing
• 1.0.9. Prepare for Emergencies
• 1.0.10. Store Attachments Safely
• 1.0.11. Road Transport Disconnect Switch
• 1.0.12. Guards and Shields
• 1.0.13. Stay Clear of Harvesting Units
• 1.0.14. Keep Hands Away From Knives
• 1.0.15. Stay Clear of Rotating Drivelines
• 1.0.16. Ballasting for Safe Ground Contact
• 1.0.17. Practice Safe Maintenance
• 1.0.18. Service Machines Safely
• 1.0.19. Support Machine Properly
• 1.0.20. Park Machine Safely
• 1.0.21. Avoid Contact With Moving Parts
• 1.0.22. Avoid Contact With Cutterbar
• 1.0.23. Service Belts Safely
• 1.0.24. Transport Safely
• 1.0.25. Observe Maximum Transport Speed
• 1.0.26. Service Tires Safely
• 1.0.27. Avoid HighPressure Fluids
• 1.0.28. Remove Paint Before Welding or Heating
• 1.0.29. Protect Against High Pressure Spray
• 1.0.30. Avoid Heating Near Pressurized Fluid Lines
• 1.0.31. Dispose of Waste Properly
• 1.0.32. Replace Safety Signs
• 1.1. Transporting
• 1.1.1. Transporting
• 1.1.2. Preparing Platform for Transport (If Equipped with Slow Speed In
• 1.1.3. Preparing Platform for Field Operation (If Equipped with Slow Sp
• 1.2. Attaching and Detaching
• 1.2.1. Attaching Platform to Combine
• 1.2.2. Detaching Platform from Combine
• 1.2.3. Feeder House Manual Unlatching
• 1.2.4. Replacement Shear Screw Location
• 1.3. Calibration and Programing
• 1.3.1. When to Calibrate
• 1.3.2. Calibration Error Codes
• 1.3.3. Active Header Control Display
• 1.3.4. Automatic Header Height Control System
• 1.4. Operating the Platform
• 1.4.1. General Information
• 1.4.2. Armrest Functions
• 1.4.3. Draper Belt Speed
• 1.4.4. Draper Belt Speed Adjust Switch (If Equipped)
• 1.4.5. Setting Backshaft Speed
• 1.4.6. Cutterbar Tilt Adjust Switch (If Equipped)
• 1.4.7. Reel Settings
• 1.4.8. Feed Drum Settings
• 1.4.9. Automatic Header Height Control
• 1.4.10. Recommended Combine Settings
• 1.4.11. Recommended Initial Crop Settings
• 1.4.12. Harvesting in Dry Crop Conditions
• 1.4.13. Harvesting in Tough Feeding Crop Conditions
• 1.4.14. Harvesting in Short, Thin Crops
• 1.4.15. Harvesting in Down Crops
• 1.4.16. Bushy or High Volume Crops
• 1.4.17. Sorghum
• 1.4.18. Seed Loss Chart
• 1.5. Attachments and Options
• 1.5.1. Feeding Auger
• 1.5.2. Long Divider Points
• 1.5.3. Knife Guards (4 in.)
• 1.5.4. Plastic Skid Shoes
• 1.5.5. Crop Lifters
• 1.5.6. Crop Lifter Adjustments
• 1.5.7. Reel End Fingers
• 1.6. Adjustments Suspension and Leveling
• 1.6.1. Leveling Draper Cutterbar to Ground
• 1.6.2. Equalize the Float System
• 1.6.3. Lock and Unlock the Float System
• 1.6.4. Lock and Unlock Gauge Wheels (If Equipped)
• 1.7. Adjustments Feeding Related
• 1.7.1. Platform AdjustmentFeeding
• 1.7.2. Cutterbar Tilt
• 1.7.3. Feed Drum Finger Timing
• 1.7.4. Side Draper Belt Tension
• 1.7.5. Center Draper Belt Tension
• 1.7.6. Knife HoldDown Clearance
• 1.8. Adjustments Windrow Conversion
• 1.8.1. Removing Center Feed Assembly
• 1.9. Adjustments Reel
• 1.9.1. Set Reel Safety Stops
• 1.9.2. Minimum Reel Height and Leveling Reel
• 1.9.3. Rephase and Bleed Lift Cylinders
• 1.9.4. Finger Pickup Settings
• 1.9.5. Hydraulic Adjustment of Fore/Aft
• 1.9.6. Fore/Aft Cylinder Mount Adjustments
• 1.9.7. Speed Ratio Sensor Adjustment
• 1.9.8. Adjust Reel Drive Gear
• 1.10. Lubrication
• 1.10.1. Lubrication
• 1.10.2. Lubricant Storage
• 1.10.3. Alternative and Synthetic Lubricants
• 1.10.4. Lubrication Interval Chart
• 1.10.5. Every 50 Hours of Operation
• 1.10.6. Every 200 400 Hours of Operation
• 1.11. Maintenance
• 1.11.1. Feeder House Safety Stop
• 1.11.2. Open Side Shields
• 1.11.3. Remove and Install Side Shields
• 1.11.4. Remove and Install Backshaft Drive Belts
• 1.11.5. Remove and Install Telescoping Knife Drive Shaft
• 1.11.6. Cutterbar Maintenance
• 1.11.7. Knife Section Service Kit
• 1.11.8. Remove and Install Cutterbar Knife
• 1.11.9. Remove and Install Knife Sections
• 1.11.10. Align Knife Head and Knife Drive
• 1.11.11. Spare Knife Storage
• 1.11.12. Remove and Install Knife Guards
• 1.11.13. Center Draper Cleanout
• 1.11.14. Cleaning Material Build Up at Side Shields
• 1.11.15. Remove and Install Side Draper Belts
• 1.11.16. Remove and Install Center Draper Belt
• 1.11.17. Remove and Install Feed Drum Finger Guides
• 1.11.18. Remove and Install Feed Drum Fingers
• 1.11.19. Header Warning Light Bulb Replacement
• 1.11.20. Remove and Install Sump Pan
• 1.11.21. Removing Center Feed Assembly
• 1.12. Storage
• 1.12.1. End of Season Service
• 1.12.2. Beginning of Season Service
• 1.13. Troubleshooting
• 1.13.1. Cutting Platform
• 1.14. Specifications
• 1.14.1. Overall Dimensions
• 1.14.2. Gauge Wheel Tire Pressure
• 1.14.3. Cutterbar
• 1.14.4. Platform Weights
• 1.14.5. Header Identification Number
• 1.14.6. Keep Machines Secure
• 1.14.7. Keep Proof of Ownership
• 1.14.8. Metric Bolt and Screw Torque Values
• 1.14.9. Unified Inch Bolt and Screw Torque Values
• 1.15. John Deere Service Literature Available
• 1.15.1. Technical Information
• 1.16. John Deere Service Keeps You On The Job
• 1.16.1. John Deere Is At Your Service
• 2. Page Number
• 2.1. Section 05
• 2.2. Section 10
• 2.3. Section 15
• 2.4. Section 20
• 2.5. Section 25
• 2.6. Section 30
• 2.7. Section 35
• 2.8. Section 40
• 2.9. Section 45
• 2.10. Section 50
• 2.11. Section 55
• 2.12. Section 60
• 2.13. Section 65
• 2.14. Section 70
• 2.15. Section 75