John Deere 722X, 725X, 730X, 735X, 740X Cutting Platform Operator Manual OMDXE11077

Description

• Model List:
  • 722X Cutting Platform
  • 725X Cutting Platform
  • 730X Cutting Platform
  • 735X Cutting Platform
  • 740X Cutting Platform

• 1. Introduction
• 1.1. Foreword
• 1.2. Trademarks
• 1.3. A Message to Our Customers
• 1.4. John Deere Technical Information Bookstore
• 1.5. Recognize Safety Information
• 1.6. Follow Safety Instructions
• 1.7. Observe Road Traffic Regulations
• 1.8. Use Safety Lights and Devices
• 1.9. Prepare for Emergencies
• 1.10. Wear Protective Clothing
• 1.11. Store Attachments Safely
• 1.12. Guards and Shields
• 1.13. Stay Clear of Harvesting Units
• 1.14. Keep Hands Away From Knives
• 1.15. Stay Clear of Rotating Drivelines
• 1.16. Stay Clear of Cutterbar When Rotating Auger
• 1.17. Ballasting for Safe Ground Contact
• 1.18. Practice Safe Maintenance
• 1.19. Service Machines Safely
• 1.20. Service Drive Belts Safely
• 1.21. Support Machine Properly
• 1.22. Protect Against Noise
• 1.23. Avoid Heating Near Pressurized Fluid Lines
• 1.24. Avoid HighPressure Fluids
• 1.25. Decommissioning Proper Recycling and Disposal of Fluids and Components
• 1.26. Road Transport Disconnect Switch
• 1.27. Replace Safety Signs
• 1.28. Safety Signs
• 2. Field Operation
• 2.1. Cutting PlatformtoCombine Adaptation
• 2.1.1. 735X, and 740X with Narrow Feeding Channel Only
• 2.1.2. with Wide Feeding Channel Only
• 2.2. Rework the WT or S Series Combine (If Necessary)
• 2.3. Attach Cutting Platform
• 2.4. Adjust Cutting Platform Tilt Angle
• 2.5. Header Height Control Feeler Sensors
• 2.6. Detach Cutting Platform
• 2.7. Transport Cutting Platform on a Trailer
• 2.8. Cutting Platform Emergency Mode
• 2.9. Calibrate Cutting Platform
• 2.10. Cutterbar and Reel Safety Feature
• 2.11. Cutterbar and Reel Safety FeatureSelf Test
• 2.12. Engage Cutting Platform Drive
• 2.13. Operate the Cutting PlatformGeneral
• 2.13.1. Cutting Platform Controls
• 2.13.2. Cutterbar Position
• 2.13.3. Cutting Height
• 2.13.4. Reel Settings
• 2.13.5. Auger Settings
• 2.14. Operate the Cutting PlatformCrop Condition Adaptation
• 2.15. Composite Reel Tines (Option)
• 2.16. Knife Speed Increase Kit
• 2.17. Fine Knife (Option)
• 2.18. Crop Dividers (Option)
• 2.18.1. Foldable Crop Divider Transport Position
• 2.18.2. Store Crop Dividers (722X Only)
• 2.18.3. Store Crop Dividers (725X740X)
• 2.19. Long Outer Deflector Kit
• 2.20. Rapeseed Knife (Option)
• 2.20.1. Store Rapeseed Knives (722X Only)
• 2.20.2. Store Rapeseed Knives (725X 740X)
• 2.21. Rapeseed Knife Lower Protection (Option)
• 2.22. Crop Lifters (Option)
• 2.22.1. Arrangement of Crop Lifters
• 2.22.2. Adapt Crop Lifters to Ground Conditions
• 2.23. Knife Protection Guard (If Equipped)
• 2.24. Troubleshooting
• 2.24.1. Cutterbar Difficulties
• 2.24.2. Down and Tangled Crops Difficulties
• 2.24.3. Feeder House Difficulties
• 2.24.4. Auger Difficulties
• 2.24.5. Cutting Difficulties
• 2.24.6. Reel Difficulties
• 2.25. Safety Lock for Feeder House Lift Cylinder (X9 Series Combines Only)
• 2.26. Safety Stop for Feeder House Lift Cylinder (WT and S Series Combines Only)
• 2.27. Set Safety Stop for Reel Lift Cylinder
• 2.28. Clean Cutterbar Table
• 2.29. Adjust Cutterbar Position
• 2.30. Adjust Reel Tine Pitch
• 2.31. Adjust Reel Support Position
• 2.32. Adjust Auger Height
• 2.33. Adjust Auger Fore/Aft
• 2.34. Adjust Auger Finger Timing
• 2.35. Adjust Rear Stripper
• 2.36. Adjust Floor Stripper
• 3. Lubrication and Maintenance
• 3.1. Required EmissionRelated Information
• 3.1.1. Service Provider
• 3.2. Safety Lock for Feeder House Lift Cylinder (X9 Series Combines Only)
• 3.3. Safety Stop for Feeder House Lift Cylinder (W, T, and S Series Combines Only)
• 3.4. Set Safety Stop for Reel Lift Cylinder
• 3.5. Side Shields
• 3.6. Tool Box (Option)
• 3.7. Gear Oil
• 3.8. Alternative and Synthetic Lubricants
• 3.9. Mixing of Lubricants
• 3.10. Lubricant Storage
• 3.11. Maintenance Interval Chart
• 3.12. Lubrication Chart
• 3.13. Main Drive Gear Case
• 3.14. Knife Drive Gear Case
• 3.15. Auger Drive Slip Clutch
• 3.16. Cutterbar Table Sheet and Sealing Bridge
• 3.17. Header Height Control SensorsOnce a Year
• 3.18. Check Reel Zero Setting
• 3.19. Hydraulic Valve Blocks
• 3.20. Rephase Reel Fore/Aft Cylinders
• 3.21. Rephase Reel Lift Cylinders
• 3.22. Adjust Reel Speed Sensor
• 3.23. Adjust Knife Drive Belt Tension
• 3.24. Replace Feeler Sensor Skid Plate
• 3.25. Replace Knife Drive Belts
• 3.26. Replace Cutterbar Knife
• 3.27. Replace Cutterbar Wear Plates
• 3.28. Set Knife Timing (735X and 740X Only)
• 3.29. Align Knife Head and Knife Drive
• 3.30. Replace Knife Sections
• 3.31. Adjust Auger Drive Chain Tension
• 3.32. Replace Auger Fingers and Retainers
• 3.33. Replace Stubble Light Bulb (NonLight Emitting Diode (LED) LightsIf Equipped)
• 3.34. Replace Stubble Light (Light Emitting Diode (LED) LightsIf Equipped)
• 3.35. End of Season
• 3.36. Beginning of Season Service
• 4. Specifications
• 4.1. 740X Cutting Platforms
• 4.1.1. Cutting Platform
• 4.1.2. Conveyor Auger
• 4.1.3. Slip ClutchTorque
• 4.2. Type Plates
• 4.3. Cutting Platform (Product Identification) Type Plate
• 4.4. Product Identification Number
• 4.5. Machine Component Serial Numbers
• 4.6. Metric Bolt and Screw Torque Values
• 4.7. Unified Inch Bolt and Screw Torque Values
• 4.8. Keep Machines Secure
• 4.9. Keep Proof of Ownership
• 4.10. EU Declaration of Conformity
• 4.11. Machine Design Life
• 5. John Deere Service Literature Available
• 5.1. Technical Information
• 6. John Deere Service Keeps You On the Job
• 6.1. John Deere Parts
• 6.2. The Right Tools
• 6.3. WellTrained Technicians
• 6.4. Prompt Service