John Deere AutoTrac Controller 300 Operator Manual OMPFP23355
$30
- Type Of Manual: Operator Manual
- Manual ID: OMPFP23355
- Format: PDF
- Size: 2.4MB
- Number of Pages: 64
Description
-
Model List:
- AutoTrac Controller 300
- 1. Introduction
- 1.1. Foreword
- 1.2. John Deere Technical Information Bookstore
- 1.3. Recognize Safety Information
- 1.4. Understand Signal Words
- 1.5. Follow Safety Instructions
- 1.6. Practice Safe Maintenance
- 1.7. Use Steps and Handholds Correctly
- 1.8. Handle Electronic Components and Brackets Safely
- 1.9. Use Electronic Display Properly
- 1.10. Operate Guidance Systems Safely
- 1.11. Use Seat Belt Properly
- 1.12. Operate AutoTrac Controller 300 Safely
- 1.13. AutoTrac Controller 300 Machine Types
- 1.14. Avoid HighPressure Fluids
- 2. Safety Signs
- 2.1. Safety Warning AutoTrac Detected
- 2.2. Safety Warning Steering Calibration
- 3. Regulatory and Compliance Information
- 3.1. Federal Communications Commission NotificationFlow Switch
- 3.2. Federal Communications Commission NotificationMotor
- 3.3. Identify Date Code
- 3.4. Identify Date Code
- 3.5. EU Declaration of Conformity
- 3.6. EU Declaration of Conformity
- 3.7. UK Declaration of Conformity
- 3.8. UK Declaration of Conformity
- 3.9. Eurasian Economic Union
- 3.10. End User License Agreement
- 4. System Overview
- 4.1. Theory of Operation
- 4.2. AutoTrac Controller 300 Requirements
- 4.3. AutoTrac Accuracy
- 4.4. AutoTrac Status Pie
- 5. Component Overview
- 5.1. StarFire Receiver
- 5.2. GreenStar Display or Generation 4 Display
- 5.3. AutoTrac Controller 300 Motor and Valve Assembly
- 5.4. Isolation Valve
- 5.5. Flow Switch
- 5.6. Road and Resume Switch
- 6. Setting Up
- 6.1. Configure Display and Receiver
- 6.2. Read and Accept AutoTrac Warning
- 6.3. GreenStar Display and Generation 4 Display Activations
- 6.4. StarFire Receiver Activations
- 6.5. Activations Tab
- 6.6. StarFire Height, Fore/Aft, and Wheelbase
- 6.7. StarFire Measurements Table
- 6.8. Enter Machine Information and Offsets
- 6.9. Calibrate Terrain Compensation Module (TCM)
- 7. Setting UpAutoTrac Controller 300
- 7.1. Determine Steer Asymmetry
- 7.2. Determine Reactive or NonReactive Steering
- 7.3. Set Up Machine Configuration
- 7.4. Test Steering
- 7.5. Remove Air from Steering System
- 7.6. Calibrate Steering System
- 7.7. Calibrate Steering Ratio
- 8. OperatingAutoTrac
- 8.1. Create Guidance Line
- 8.2. Enable AutoTrac
- 8.3. Disable AutoTrac When Not In Use
- 8.4. Engage System
- 8.5. Disengage, Deactivate, and Disable System
- 9. OperatingOptimizing AutoTrac
- 9.1. AutoTrac Settings
- 10. Troubleshooting
- 10.1. Installation Calibration Observable Symptoms
- 10.2. Observable Symptoms
- 10.3. Diagnostic Readings
- 10.4. AutoTrac Status Tab
- 10.5. Motor Readings Tab
- 10.6. Motor Information Tab
- 10.7. Disengage and Engage Thresholds
- 10.8. Diagnostic Addresses
- 10.9. AutoTrac Controller Diagnostic Trouble Codes
- 10.10. AutoTrac Status Pie Diagnostic Readings
- 10.11. AutoTrac Exit Codes
- 10.12. Guidance Alarms
- 11. Maintenance
- 11.1. Preseason Checklist
- 11.2. PostSeason Checklist
- 11.3. Daily Checklist
- 12. John Deere Service Literature Available
- 12.1. Technical Information
- 13. John Deere Service Keeps You On Job
- 13.1. John Deere Is At Your Service
Related products
-50%
Original price was: $20.$10Current price is: $10.
-50%
Original price was: $20.$10Current price is: $10.
-50%
Original price was: $20.$10Current price is: $10.
-50%
Original price was: $20.$10Current price is: $10.
-50%
Original price was: $20.$10Current price is: $10.
-50%
Original price was: $20.$10Current price is: $10.
