Description
-
Model List:
- AutoTrac Controller-Reichhardt
- 1. Contents
- 1.0.1. Recognize Safety Information
- 1.0.2. Understand Signal Words
- 1.0.3. Follow Safety Instructions
- 1.0.4. Practice Safe Maintenance
- 1.0.5. Use Steps and Handholds Correctly
- 1.0.6. Handle Electronic Components and Brackets Safely
- 1.0.7. Use Electronic Display Properly
- 1.0.8. Operate Guidance Systems Safely
- 1.0.9. Use Seat Belt Properly
- 1.0.10. Use AutoTrac Controller on Approved Vehicles
- 1.1. Safety Signs
- 1.1.1. Automatic Guidance System Detected
- 1.1.2. Wheel Movement
- 1.1.3. Wheel Movement
- 1.1.4. Wheel Movement
- 1.2. Regulatory and Compliance Information
- 1.2.1. EU Declaration of Conformity
- 1.3. System Overview
- 1.3.1. Theory of Operation
- 1.3.2. AutoTrac Reichhardt Requirements
- 1.3.3. AutoTrac Accuracy
- 1.4. Softkey Legend
- 1.4.1. StarFire ReceiverStarFire Softkey
- 1.4.2. GreenStarGuidance Softkey
- 1.4.3. AutoTrac Controller Menu Softkey
- 1.5. Component Overview
- 1.5.1. GreenStar Display
- 1.5.2. StarFire 3000 Receiver
- 1.5.3. Reichhardt Steering Controller
- 1.5.4. ElectroHydraulic Valve
- 1.5.5. Steering Input Device
- 1.5.6. Resume Switch
- 1.5.7. Master Switch
- 1.5.8. Seat Switch and Activity Monitor
- 1.6. Setting UpAutoTracReichhardt
- 1.6.1. GreenStar Display and StarFire Receiver Software Activations
- 1.6.2. StarFire Height and ForeAft
- 1.6.3. StarFire Height and ForeAft Measurements Table
- 1.6.4. Read and Accept Warning on GreenStar Display
- 1.6.5. Optimize Terrain Compensation Module (TCM)
- 1.6.6. Set Up Terrain Compensation Module (TCM)
- 1.6.7. Calibrate Terrain Compensation Module (TCM)
- 1.6.8. AutoTrac Controller Reichhardt Main Menu
- 1.6.9. Determine Turning Diameter
- 1.6.10. Calibrate AutoTrac ControllerReichhardt
- 1.6.11. Failed Calibrations
- 1.7. OperatingGreenStar 3 2630 Display
- 1.7.1. Create Guidance Line
- 1.7.2. Enable AutoTrac
- 1.7.3. Activate System
- 1.7.4. Deactivate System
- 1.7.5. Adjust Advanced AutoTrac SettingsGreenStar 3 2630 Display
- 1.8. OperatingGreenStar 2 1800 Display
- 1.8.1. Create Guidance Line
- 1.8.2. Enable AutoTrac
- 1.8.3. Activate System
- 1.8.4. Deactivate System
- 1.8.5. Adjust Advanced AutoTrac Settings GreenStar 2 1800 Display
- 1.9. OperatingOptimizing AutoTrac Controller
- 1.9.1. Optimize AutoTrac Controller Performance
- 1.9.2. Monitor AutoTrac Performance
- 1.9.3. Optimize AutoTrac Performance
- 1.10. Troubleshooting
- 1.10.1. AutoTrac Controller
- 1.10.2. AutoTrac Controller Diagnostic Readings
- 1.10.3. AutoTrac Status Pie Diagnostic Readings
- 1.10.4. AutoTrac ControllerReichhardt Stop Codes
- 1.10.5. AutoTrac Exit Codes and Deactivation Messages
- 1.10.6. Guidance Alarms
- 1.10.7. AutoTrac ControllerReichhardt Diagnostic Addresses
- 1.10.8. AutoTrac ControllerReichhardt Diagnostic Trouble Codes
- 1.11. Checklists
- 1.11.1. Preseason Checklist
- 1.11.2. Postseason Checklist
- 1.11.3. Daily Checklist
- 1.12. John Deere Service Literature Available
- 1.12.1. Technical Information
- 1.13. John Deere Service Keeps You On Job
- 1.13.1. John Deere Is At Your Service
- 2. Page Number
- 2.1. Section 05
- 2.2. Section 10
- 2.3. Section 20
- 2.4. Section 30
- 2.5. Section 40
- 2.6. Section 50
- 2.7. Section 60
- 2.8. Section 70A
- 2.9. Section 70B
- 2.10. Section 70C
- 2.11. Section 80
- 2.12. Section 90
