John Deere 14 Foot, 16 Foot, 18 Foot With 896 Auger Platform Hay Conditioner Operator Manual OMFH309664
$30
- Type Of Manual: Operator Manual
- Manual ID: OMFH309664
- Format: PDF
- Size: 9.7MB
- Number of Pages: 132
Description
-
Model List:
- 14 Foot With 896 Auger Platform Hay Conditioner
- 16 Foot With 896 Auger Platform Hay Conditioner
- 18 Foot With 896 Auger Platform Hay Conditioner
- 1. Contents
- 1.0.1. Recognize Safety Information
- 1.0.2. Understand Signal Words
- 1.0.3. Follow Safety Instructions
- 1.0.4. Before Operating
- 1.0.5. Wear Protective Clothing
- 1.0.6. Handle Chemical Products Safely
- 1.0.7. Stay Clear of Rotating Drivelines
- 1.0.8. Use Safety Lights and Devices
- 1.0.9. Use Proper Tools
- 1.0.10. Practice Safe Maintenance
- 1.0.11. Remove Paint Before Welding or Heating
- 1.0.12. Avoid Heating Near Pressurized Fluid Lines
- 1.0.13. Avoid HighPressure Fluids
- 1.0.14. Store Attachments Safely
- 1.0.15. Dispose of Waste Properly
- 1.1. Safety Signs
- 1.1.1. Safety Signs
- 1.2. Attaching and Detaching Platform
- 1.2.1. Attaching Platform
- 1.2.2. Detaching Platform
- 1.2.3. Balancing Platform SidetoSide
- 1.3. Operating Auger Platform
- 1.3.1. Prestarting Checks
- 1.3.2. Checking Knife Drive Belt Tension
- 1.3.3. Breaking In Auger Platform
- 1.3.4. Determining Ground Speed
- 1.3.5. Knockdown Bar
- 1.3.6. Cutterbar Knife Storage
- 1.3.7. Cutterbar
- 1.3.8. Adjusting Reel Position with Hydraulic Drive Reel
- 1.3.9. Knife Overlap
- 1.3.10. Knife HoldDowns
- 1.3.11. Platform Guard Angle
- 1.3.12. Gauge Shoes
- 1.3.13. Operating Hydraulic Reel
- 1.3.14. Adjust Reel Speeds (Mechanical)
- 1.3.15. Adjust Reel Speeds (Hydraulic)
- 1.3.16. Adjusting Reel Speed Magnetic Pickup
- 1.3.17. Conditioner
- 1.3.18. Platform Float
- 1.3.19. Windrow Formation
- 1.3.20. Dirt or Mud Buildup
- 1.3.21. Cutting Alfalfa
- 1.3.22. Cutting Grass
- 1.3.23. Cutting Tall Crop
- 1.3.24. Adjusting Swath Flap
- 1.3.25. Adjusting Platform Guard Angle
- 1.3.26. Adjusting Cutting Height
- 1.3.27. Adjusting Gauge Shoes
- 1.3.28. Adjusting Knockdown Bar
- 1.3.29. Removing Lower Auger CleanOut Panels
- 1.3.30. Removing Lower Auger Center Deck Sheets
- 1.4. Attachments
- 1.4.1. Cutterbar Knife Sections
- 1.4.2. Gauge Shoe Wear Plates
- 1.4.3. Reel Drive Sprockets
- 1.4.4. Tall Crop Dividers
- 1.4.5. Hydraulic Reel Drive
- 1.5. Lubrication and Maintenance
- 1.5.1. Gear Oil
- 1.5.2. Alternative and Synthetic Lubricants
- 1.5.3. Mixing of Lubricants
- 1.5.4. Lubricant Storage
- 1.5.5. Observe Lubrication Symbols
- 1.5.6. Perform Lubrication and Maintenance
- 1.5.7. Periodic Maintenance Label (LeftHand Side of Platform)
- 1.5.8. Periodic Maintenance Label (RightHand Side of Platform)
- 1.5.9. Every Five Hours
- 1.5.10. Every Ten Hours
- 1.5.11. Every 50 Hours
- 1.6. Troubleshooting
- 1.6.1. Cutting
- 1.6.2. Feeding (Reel and Auger)
- 1.6.3. Feeding (Conditioner)
- 1.6.4. Windrow Forming
- 1.6.5. Hydraulic Driven Reel Malfunctions (If Equipped)
- 1.6.6. Miscellaneous
- 1.7. Service
- 1.7.1. Detailed Service Information (Use TM2033)
- 1.7.2. Practice Safe Service Procedures
- 1.7.3. Servicing Cutterbar (Hydraulic Reel Drive)
- 1.7.4. Care Of Chains
- 1.7.5. Care of VBelts
- 1.7.6. Platform Wiring Harness Diagram
- 1.7.7. Wiring Harness Adapter Diagram
- 1.7.8. Installing ORing Connector Link
- 1.7.9. Tightening Bearing Locking Collars
- 1.7.10. Changing Reel Speed (Mechanical Drive)
- 1.7.11. Changing Reel Speed (Hydraulic)
- 1.7.12. Adjusting Reel Drive Belt (Mechanical Drive)
- 1.7.13. Adjusting Reel Chain (Mechanical Drive)
- 1.7.14. Adjusting Reel Chain (Hydraulic Drive)
- 1.7.15. Adjusting Pump Drive Chain (Hydraulic Drive)
- 1.7.16. Adjusting Reel Height
- 1.7.17. Adjusting Reel Cam
- 1.7.18. Adjusting Conditioner Roll Timing
- 1.7.19. Adjusting Conditioner Roll Spacing
- 1.7.20. Adjusting Conditioner Roll Pressure
- 1.7.21. Adjusting Knife Drive Belt (Both Sides)
- 1.7.22. Adjusting Knife Drive Belt Alignment (Both Sides)
- 1.7.23. Adjusting Upper and Lower Strippers to Augers
- 1.7.24. Adjusting Center Strippers to Lower Auger (Optional)
- 1.7.25. Adjusting Cam Follower to Reel Cam
- 1.7.26. Replacing Reel Drive Belt (Mechanical Drive)
- 1.7.27. Replacing Knife Drive Belt (Both Sides)
- 1.7.28. Replacing Reel Cam Followers
- 1.7.29. Adjusting Cam Arm Clearance With Cam
- 1.7.30. Removing Tooth Bar
- 1.7.31. Replacing Reel Tooth Bar Bearings
- 1.7.32. Replacing Reel Teeth
- 1.7.33. Timing Knives
- 1.7.34. Knife Overlap
- 1.7.35. Removing Knives
- 1.7.36. Installing Knives
- 1.7.37. Cutterbar Knife Sections
- 1.7.38. Replacing BoltOn Knife Sections
- 1.7.39. Replacing Center Knife Sections
- 1.7.40. Adjusting Regular Knife HoldDowns
- 1.7.41. Adjusting NonClog Knife HoldDowns
- 1.7.42. Installing Regular Guards
- 1.7.43. Installing NonClog Guards
- 1.8. Storage
- 1.8.1. Removing Platform from Storage (Beginning of Season)
- 1.8.2. Storing Platform (End of Season)
- 1.9. Specifications
- 1.9.1. Auger Platform Specifications
- 1.9.2. Record Product Identification Numbers
- 1.9.3. Keep Proof of Ownership
- 1.9.4. Keep Machines Secure
- 1.9.5. Record Platform Serial Number
- 1.9.6. Metric Bolt and Screw Torque Values
- 1.9.7. Unified Inch Bolt and Screw Torque Values
- 1.10. John Deere Service Literature Available
- 1.10.1. Technical Information
- 1.11. John Deere Service Keeps You On The Job
- 1.11.1. John Deere Is At Your Service
- 2. Page Number
- 2.1. Section 05
- 2.2. Section 10
- 2.3. Section 15
- 2.4. Section 20
- 2.5. Section 25
- 2.6. Section 30
- 2.7. Section 35
- 2.8. Section 40
- 2.9. Section 50
- 2.10. Section 55
Related products
-50%
Original price was: $20.$10Current price is: $10.
-50%
Original price was: $20.$10Current price is: $10.
-50%
Original price was: $20.$10Current price is: $10.
-50%
Original price was: $20.$10Current price is: $10.
-50%
Original price was: $20.$10Current price is: $10.
