Description
-
Model List:
- IGrade and Distance Trip
- 1. Introduction
- 1.1. Foreword
- 1.2. John Deere Technical Information Bookstore
- 1.3. Recognize Safety Information
- 1.4. Understand Signal Words
- 1.5. Follow Safety Instructions
- 1.6. Practice Safe Maintenance
- 1.7. Use Steps and Handholds Correctly
- 1.8. Handle Electronic Components and Brackets Safely
- 1.9. Use Electronic Display Properly
- 1.10. Operate Guidance Systems Safely
- 1.11. Use Seat Belt Properly
- 1.12. Operate Implement Automation Systems Safely
- 1.13. Avoid HighPressure Fluids
- 2. Regulatory and Compliance Information
- 2.1. Identify Date Code
- 2.2. Eurasian Economic Union EAC
- 2.3. EU Declaration of Conformity
- 2.4. UK Declaration of Conformity
- 3. System OverviewiGrade
- 3.1. Theory of OperationiGrade
- 3.2. Grade Control
- 3.3. Plane Control
- 3.4. Remote Control
- 3.5. Origin Point
- 3.6. Satellite InformationVDOP
- 3.7. Surface Maps
- 4. System OverviewDistance Trip
- 4.1. Theory of OperationDistance Trip
- 4.2. Parallel Lines
- 4.3. Fence Post
- 4.4. Plot Pattern
- 4.5. Satellite InformationPDOP
- 5. System Overview
- 5.1. Requirements
- 5.2. Navigate to Application Controller Pages
- 5.3. Navigate to StarFire Pages
- 5.4. Enter Activation Code
- 5.5. Replace Erasable Programmable ReadOnly Memory (EPROM)
- 5.6. Machine Compatibility
- 6. Component Overview
- 6.1. StarFire Receiver
- 6.2. StarFire Global Navigation Satellite System (GNSS) Antenna (Recommended)
- 6.3. Choke Ring Antenna (Optional)
- 6.4. Display
- 6.5. UCC2 Application Controller
- 6.6. Counterbalance Valve
- 6.7. External Valve
- 7. Assembly
- 7.1. Message Definition
- 7.2. Remote Control Serial Port Hardware
- 7.3. Distance Trip Low Side Driver
- 7.4. Implement Operators Station
- 8. Setting UpEquipment
- 8.1. Connect Implement
- 8.2. Adjust Selective Control Valve (SCV)
- 8.2.1. Generation 4 CommandCenter CommandCenter is a trademark of Deere Company
- 8.2.2. GreenStarGreenStar is a trademark of Deere Company 3 CommandCenter
- 8.2.3. TouchSetTouchSet is a trademark of Deere Company Display
- 8.3. Adjust Counterbalance Valve
- 8.4. Set Up Base Station
- 8.4.1. Configure Base Station
- 8.4.2. Hour Survey
- 8.5. Set Up Global Position System (GPS) Receiver
- 8.6. Optimize Terrain Compensation Module (TCM)
- 8.7. Calibrate Terrain Compensation Module (TCM)
- 9. Setting UpUCC2 Application Controller
- 9.1. Setup Wizard Overview
- 9.2. Serial Ports
- 9.3. Set Up Run Page
- 10. Setting UpiGrade
- 10.1. GPS Offsets
- 10.2. SCV Configuration
- 10.3. Manual SCV Calibration
- 10.4. Surface
- 10.5. Elevation Offset
- 10.6. Edit Control Sensitivity
- 10.7. Load Limiting
- 10.8. Edit Load Limiting Sensitivity
- 10.9. Maximum Cut
- 11. Setting UpDistance Trip
- 11.1. Equipment Offsets
- 11.2. Trip Pattern
- 11.3. Trip Command
- 11.4. Trip Documentation
- 11.5. Enable File Server
- 11.6. Equipment Offset Calibration
- 11.7. Trip Action Test
- 11.8. Equipment Delay Calibration
- 12. Operating
- 12.1. Engage Auto Mode
- 12.2. Disengage, Deactivate, and Disable Implement Automation
- 12.3. SCV Command Control
- 12.4. Status Tab
- 12.5. Operate Distance Trip
- 12.6. Operate iGradePlane Control and Remote Control
- 12.7. Operate iGradeGrade Control
- 13. Troubleshooting
- 13.1. Reset UCC2 Application Controller
- 13.2. Status and Exit Codes
- 13.3. TroubleshootingDistance Trip System
- 13.4. TroubleshootingiGrade System
- 13.5. TroubleshootingMachine
- 13.6. External Valve
- 13.7. Data Cleanup
- 13.8. Clean Up ISOBUS VT
- 13.9. DiagnosticsDistance Trip Status
- 13.10. DiagnosticsiGrade Status
- 13.11. DiagnosticsSetpoints
- 13.12. DiagnosticsMaximum Cut
- 13.13. DiagnosticsLoad Limiting
- 13.14. DiagnosticsRemote Control
- 13.15. Hardware/Software
- 13.16. Input/Output Readings
- 13.17. SCV Diagnostics
- 14. Maintenance
- 14.1. Preseason Checklist
- 14.2. Daily Checklist
- 14.3. Postseason Checklist
- 15. John Deere Service Literature Available
- 15.1. Technical Information
- 16. John Deere Service Keeps You on The Job
- 16.1. John Deere Is At Your Service
