John Deere 180SL, 220SL, 260SL Walk Greens Mower Operator Manual OMTCU32832

Description

• Model List:
  • 180SL Walk Greens Mower
  • 220SL Walk Greens Mower
  • 260SL Walk Greens Mower

• 1. Introduction
• 1.1. Thank You for Purchasing a John Deere Product
• 1.2. Using Your Operators Manual
• 1.3. Machine Use
• 1.4. Special Messages
• 2. Product Identification
• 2.1. Record Identification Numbers
• 3. Table of Contents
• 4. Safety Labels
• 4.1. Safety Label Location
• 4.2. Pictorial Safety Signs
• 4.3. Warning
• 4.4. Warning MT3367
• 4.4.1. Keep All Shields In Place
• 4.5. WARNING TCU26800
• 4.5.1. SPARK ARRESTOR
• 4.6. Warning MT7234
• 4.6.1. Help Avoid Injury
• 4.7. Danger MT6732
• 4.7.1. Avoid Injury From Rotating Blades
• 4.8. CE Certification Label
• 4.9. Training
• 4.10. Preparation
• 4.11. Operation
• 4.12. Parking Safely
• 4.13. Maintenance and Storage
• 4.14. Checking Mowing Area
• 4.15. Avoid Injury From Contacting Blades
• 4.16. Rotating Blades are Dangerous Protect Children and Prevent Accidents
• 4.16.1. Protect Children
• 4.17. Wear Appropriate Clothing
• 4.18. Prevent Fires
• 4.19. Handling Fuel Safely
• 4.19.1. To avoid personal injury or property damage, use extreme care in handling fuel. Fuel is extremely…
• 4.20. Handling Waste Product and Chemicals
• 5. Operating Controls
• 5.1. Operating Controls
• 6. Operating
• 6.1. Daily Operating Checklist
• 6.2. Avoid Damage to Plastic and Painted Surfaces
• 6.3. Adjusting Handlebar
• 6.4. Using Operator Controls
• 6.4.1. Using Run Switch
• 6.4.2. Using Operator Presence Bail
• 6.4.3. Using Travel Clutch Lever (Forward Travel)
• 6.4.4. Using Park Brake Lever
• 6.4.5. Using Throttle Lever
• 6.4.6. Using Choke Lever
• 6.4.7. Using Fuel ShutOff Valve
• 6.4.8. Using Greens Tender Conditioner (GTC) Handle
• 6.5. Using Reel Clutch Handle
• 6.6. Removing Transport Wheels
• 6.7. Starting the Engine
• 6.8. Stopping the Engine
• 6.9. Testing Safety Systems
• 6.10. Testing Park Brake
• 6.11. Testing Run Switch
• 6.12. Testing Operator Presence Bail
• 6.13. Transporting Machine on Trailer
• 6.14. Emergency Stopping
• 7. Operating Cutting Units
• 7.1. Cleaning Cutting Unit
• 7.2. Adjusting Bed KnifeToReel
• 7.3. Adjusting Cutting Height
• 7.4. Adjusting Drive Roller Parallel with Bed Knife
• 7.5. Operating (Optional) Turf Conditioner Or Rotary Brush
• 7.5.1. Rotary Brush
• 7.5.2. Engaging the GTC or Rotary Brush
• 7.5.3. Disengaging the GTC or Rotary Brush
• 7.6. Adjusting Greens Tender Conditioner (GTC) Or Rotary Brush
• 7.7. Adjusting Front Roller Position
• 7.8. Removing and Installing Grass Catcher
• 7.9. Operating Turf Broom
• 8. Replacement Parts
• 8.1. Service Literature
• 8.1.1. Order Service Parts Online
• 8.2. Part Numbers
• 8.2.1. Standard Bed Knives
• 8.2.2. Tournament Bed Knives
• 8.2.3. LowCut Bed Knives
• 8.2.4. Fairway Bed Knives
• 9. Service Intervals
• 9.1. Servicing Your Machine
• 9.2. Breakin After 5 Hours
• 9.3. Breakin After First 20 Hours
• 9.4. Breakin After 50 Hours
• 9.5. Every 50 Hours
• 9.6. Every 100 Hours
• 9.7. Every 300 Hours
• 9.8. Yearly or every 500 Hours
• 10. Service Lubrication
• 10.0.1. The following greases are preferred
• 10.1. Transmission and Hydraulic Oil
• 10.2. Biodegradable Oil
• 10.2.1. Application
• 10.2.2. Cold Weather Operation
• 10.3. Converting From HYGARD to BIO HYGARD
• 10.4. Lubricating Rotary Brush Or GTC (Greens Tender Conditioner)
• 10.5. Lubricating Reel
• 10.6. Lubricating Input Drives
• 10.7. Lubricating Front Roller
• 10.8. Lubricating Drive Roller
• 10.9. Checking and Filling Gear Case
• 10.10. Lubricating Knife Shoe Pivot Bolt
• 10.11. Lubricating Drive Control Linkage
• 10.12. Lubricating Operator Presence Pawl And Cam
• 10.13. Lubricating Height of Cut Bracket
• 11. Service Engine
• 11.1. Engine Warranty Maintenance Statement
• 11.2. Avoid Fumes
• 11.3. Engine Oil
• 11.3.1. The following oils are also recommended
• 11.3.2. Other oils may be used if they meet one or more of the following
• 11.4. Using Proper Fuel
• 11.5. Filling Fuel Tank
• 11.6. Adjusting Throttle Lever Location
• 11.7. Adjusting Throttle Lever Tension
• 11.8. Cleaning Air Cleaner
• 11.9. Cleaning Fuel Sediment Bowl and Fuel Filter
• 11.10. Checking Engine Oil Level
• 11.11. Changing Engine Oil
• 11.12. Cleaning Spark Plug And Adjusting Electrode Gap
• 11.13. Adjusting Carburetor
• 12. Service Belts
• 12.1. Removing Drive Belts
• 12.2. Installing Belts
• 12.3. Drive Belt Tension Check and Adjustment
• 12.3.1. Check Procedure
• 12.3.2. Adjustment Procedure
• 12.3.3. Determine Type of Adjustment Required
• 12.3.4. Coarse Adjustment Procedure
• 12.3.5. Fine Adjustment Procedure
• 12.4. Adjusting Belt Guide
• 12.5. Adjusting Operator Presence Bail
• 13. Service Cutting Units
• 13.1. Backlapping
• 13.2. Removing And Installing Bed Knife And Shoe
• 13.3. Grinding the Bed Knife
• 13.4. Adjusting Reel Or Roller Drive Chains
• 13.5. Adjusting Brake
• 13.6. Adjusting Reel Shield
• 13.7. Checking Tire Pressure (Transport Wheels)
• 14. Troubleshooting
• 14.1. Using Troubleshooting Chart
• 15. Storage
• 15.1. Storing Safety
• 15.2. Preparing Machine for Storage
• 15.3. Preparing Fuel and Engine For Storage
• 15.3.1. Fuel Usage with Stabilizers or Conditioners.
• 15.3.2. Fuel Usage without Stabilizers or Conditioners.
• 15.3.3. Engine
• 15.4. Removing Machine From Storage
• 16. Assembly
• 16.1. Attach Handlebar
• 16.2. Install Brake And Travel Clutch Cables
• 16.3. Adjusting Brake
• 16.4. Drive Belt Tension Check and Adjustment
• 16.4.1. Check Procedure
• 16.4.2. Adjustment Procedure
• 16.4.3. Determine Type of Adjustment Required
• 16.4.4. Coarse Adjustment Procedure
• 16.4.5. Fine Adjustment Procedure
• 16.5. Install Throttle Cable
• 16.6. Install Run Switch Cable
• 16.7. Install Front Roller
• 16.8. Install Kick Stand (Optional)
• 16.9. Install Transport Wheels (Optional)
• 16.10. Check Fluid Levels
• 16.11. Engine BreakIn
• 16.12. Checking Machine Safety System
• 17. Specifications
• 17.0.1. Adjustment Specifications
• 17.1. Fuel System
• 17.1.1. Fuel Types (Recommended)
• 17.2. Capacities
• 17.3. Travel Speeds
• 17.3.1. Traveling Device (Maximum Forward Speed)
• 17.4. Tire Dimensions
• 17.5. Dimensions
• 17.5.1. Width (With transport wheels installed)
• 17.5.2. Weight (With grass catcher, less transport wheels and Brush/GTC drive)
• 17.6. Cutting Unit
• 17.6.1. Greens Tender Conditioner (Optional)
• 17.6.2. Frequency of Clip
• 17.6.3. Cutting Height (Minimum)
• 17.6.4. Cutting Width
• 17.6.5. Clutches
• 17.7. Miscellaneous
• 17.8. Recommended Lubricants
• 17.9. Speed of Rotation of the Cutting Device
• 17.10. Sound Measurements
• 17.10.1. Averaged Sound Level at Work Station According to ISO112011995
• 17.11. Vibration Measurements
• 17.11.1. Hand/Arm Measured Per EN8361997A2
• 18. Declaration of Conformity
• 18.1. EC Declaration of Conformity
• 19. Declaration of Conformity
• 19.1. EC Declaration of Conformity
• 20. Declaration of Conformity
• 20.1. EC Declaration of Conformity
• 21. Service Statement
• 21.1. John Deere Parts
• 21.2. The Right Tools
• 21.3. WellTrained Technicians
• 21.4. Prompt Service
• 22. Service Record
• 22.1. Record Service Dates