Description
-
Model List:
- 200 Series Flail Shredder
- 1. Introduction
- 1.1. Foreword
- 1.2. Identification View
- 1.3. A Message to Our Customers
- 1.4. Preliminary Checks
- 1.5. Regions and Country Versions
- 1.6. Machine Overview
- 2. Safety
- 2.1. Recognize Safety Information
- 2.2. Understand Signal Words
- 2.3. Follow Safety Instructions
- 2.4. Keep Riders Off Machine
- 2.5. Prepare for Emergencies
- 2.6. Wear Protective Clothing
- 2.7. Use Seat Belt Properly
- 2.8. Use Safety Lights and Devices
- 2.9. Practice Safe Maintenance
- 2.10. Avoid HighPressure Fluids
- 2.11. Store Attachments Safely
- 2.12. Protect Against Noise
- 2.13. Stay Clear of Rotating Drivelines
- 2.14. Remove Paint Before Welding or Heating
- 3. Safety Signs
- 3.1. Rotor Drive Shield Decal
- 3.2. Flail Shredder Rear Side Decals
- 3.3. Rotor Drive Decal
- 3.4. Flail Shredder Front Side Decal
- 3.5. Gear Case Shield Decal
- 3.6. Hitch Decal
- 3.7. Three Point Hitch Decals
- 4. Preparing the Tractor
- 4.1. Tractor Size
- 4.2. Positioning Tractor Drawbar
- 4.3. Adjusting Tractor Drawbar and Hitch(Drawn Flail Shredder)
- 4.4. Adjusting Tractor Hitch(Integral Flail Shredder)
- 4.5. Checking Ballast, Wheel Spacing, and Tire Inflation
- 4.6. Tractor Brakes
- 5. Preparing the Machine
- 5.1. Adjusting Wheel Spacing on Drawn Flail Shredder
- 5.2. Before You Start
- 6. Attaching and Detaching
- 6.1. Attaching Drawn Shredder to Tractor
- 6.2. Detaching Drawn Shredder from Tractor
- 6.3. Use Correct Hose Tips
- 6.4. Attaching PTO Driveline
- 6.5. Attaching Integral Flail Shredder
- 7. Transporting
- 7.1. Keep Riders Off Machine
- 7.2. Use a Safety Chain
- 7.3. Use Safety Lights and Devices
- 7.4. Tow Loads Safely
- 7.5. Observe Maximum Transport Speed
- 7.6. Transporting Drawn Flail Shredder
- 7.7. Transporting Drawn Flail Shredder Using EasyEnd Transport
- 7.8. Preparing the Shredder for Transport
- 7.9. Follow Safe Transport Procedures
- 7.10. Transporting Integral Flail Shredder
- 8. Operating the Machine
- 8.1. BrakeIn the Shredder
- 8.2. Keep Riders off Machine
- 8.3. Follow Safe Operating Procedures
- 8.4. Operating Shredder for Best Performance
- 8.5. Maintaining Rotor Balance
- 8.6. Adjusting Rotor Drive Belts
- 8.7. Adjusting Cutting Height on Drawn Flail Shredder
- 8.8. Adjusting Cutting Height on Integral Flail Shredder
- 9. Attachments
- 9.1. Disk Hitch (Drawn Flail Shredder)
- 9.2. Center Crop Divider (Drawn Flail Shredder)
- 9.3. Center Divider and Skid Shoe (Integral Flail Shredder)
- 9.4. Crop Deflectors
- 9.5. EasyEnd Transport(220 Drawn Flail Shredder)
- 9.6. PTO Drivelines Used on Drawn Flail Shredder
- 9.7. PTO Drivelines Used on Integral Flail Shredder
- 9.8. Safety Chain
- 10. Lubrication and Maintenance
- 10.1. Lubricating and Maintaining Machine Safely
- 10.2. Gear Case Lubricant
- 10.3. Grease for General Use
- 10.4. Perform Lubrication and Maintenance
- 10.5. Lubrication Intervals
- 10.6. PTO Driveline
- 10.7. Wheel Supports
- 10.8. Drive Pulley
- 10.9. Wheel Support
- 10.10. Adding Oil to the Gear Case
- 10.11. Wheel Bearing
- 11. Trouble Shooting
- 11.1. Knife Troubleshooting
- 11.2. General Troubleshooting
- 11.3. Operation Troubleshooting
- 12. Service
- 12.1. Practice Safe Service Procedures
- 12.2. Rotor Knives
- 12.3. Inspecting Knives
- 12.4. Inspecting Knife Fasteners
- 12.5. Replacing Knives
- 12.6. Gear Case Service
- 12.7. Bearing Guards
- 12.8. Crop Deflectors
- 12.9. Bearing Locking Collars
- 12.10. Rotor Drive Belts
- 12.11. Wheel Bearings(Drawn Flail Shredder)
- 13. Storage
- 13.1. Store Attachments Safely
- 13.2. End of Season
- 13.3. Beginning of Season
- 14. Assembly
- 14.1. SetUp Time
- 14.2. Assembling Shredder Safely
- 14.3. Assembling Drawn Flail Shredder
- 14.4. Disk Hitch
- 14.5. EasyEnd Transport
- 14.6. Center Crop Divider
- 14.7. Integral Flail Shredder Assemble Mast Brackets and Strap
- 14.8. Installing Warning Lights
- 14.9. Installing Tool Box
- 14.10. Installing Drive Shaft
- 14.11. Installation of Center Divider (Attachment)
- 14.12. Slow Moving Vehicle Emblem(Integral Flail Shredder)
- 15. Specifications
- 15.1. Specifications
- 15.2. Unified Inch Bolt and Screw Torque Values
- 15.3. Metric Bolt and Screw Torque Values
- 15.4. Serial Number
- 16. John Deere Service Keeps You On Job
- 16.1. John Deere Is At Your Service
- 16.2. John Deere Parts
- 16.3. The Right Tools
- 16.4. WellTrained Technicians
- 16.5. Prompt Service
