Description
-
Model List:
- 206C Corn Harvesting Device
- 1. Introduction
- 1.1. Foreword
- 1.2. Outline
- 2. Safety Instructions and Safety Signs
- 2.1. Recognize Safety Information
- 2.2. Follow Safety Instructions
- 2.3. Understand Signal Words
- 2.4. Prepare for Emergencies
- 2.5. Wear Protective Clothing
- 2.6. Do Not Get Close to the Header
- 2.7. Keep Hands Away from Blades
- 2.8. Road Safety Rules
- 2.9. Proper Load of Front and Rear Axles
- 2.10. Running of Combine and Header
- 2.11. Retighten Nuts of Front and Rear Wheels
- 2.12. Use Proper Tools
- 2.13. Store Attachments Safely
- 2.14. Support Machine Properly
- 2.15. Install All Guards
- 2.16. Avoid HighPressure Fluids
- 2.17. Practice Safe Maintenance
- 2.18. Service Machines Safely
- 2.19. Avoid Heating Near Pressurized Fluid Lines
- 2.20. Decommissioning Proper Recycling and Disposal of Fluids and Components
- 2.21. Handle Agricultural Chemicals Safely
- 2.22. Remove Paint Before Welding or Heating
- 2.23. Safety Sings
- 2.23.1. Pictorial Safety Signs
- 2.23.2. Shields on Header Drives
- 2.23.3. Safety Stop
- 2.23.4. Rotating Driveline
- 2.23.5. Header Entanglement
- 2.23.6. Reflector
- 3. Attaching and Detaching
- 3.1. Attaching Header to Feeder House
- 3.2. Feeder House Safety Stop
- 3.3. Header Driveshaft
- 4. Operating Corn Head
- 4.1. General Information
- 4.2. Starting in the Field
- 4.3. Adjust Corn Header Properly
- 4.4. Drive and Operate Carefully
- 4.5. Corn Head Drive Speeds
- 4.6. Harvesting Corn with Weakened or Broken Stalks
- 4.7. Harvesting Popcorn
- 4.8. Gatherers
- 5. Header Adjustment
- 5.1. Hoisting Beam
- 5.2. Adjust Crop Dividers
- 5.3. Raise Shields
- 5.4. Ear Savers
- 5.5. Adjust Trash Knife
- 5.6. Adjust Knife of Stalk Roll
- 5.7. Adjust Stalk Roll
- 5.8. Adjust Gatherer Chain Tension
- 5.9. Adjust Deck Plates
- 5.10. Adjust Auger
- 5.11. Adjust Clutch
- 6. Lubrication and Maintenance
- 6.1. Front End of Stalk Roll
- 6.2. Tension Sprocket
- 6.3. Gear Case
- 7. Analysis and Troubleshooting of Failures
- 7.1. Reminder
- 7.2. Grain Loss
- 7.3. Corn Falls off from Stalk Rolls
- 7.4. Corn Is Not Threshed Completely
- 7.5. Corn Is Over Threshed
- 7.6. Corn Loss at the Rear Part of Combine
- 7.7. Corn Stalks Are Rejected
- 7.8. Blockage
- 7.9. Threshed Corn Kernels Are Found at the Rear of Combine
- 7.10. Corn Slips Out
- 7.11. Spoiled Corn Kernels or Crushing Loss
- 7.12. Feeder House Inlet Is Blocked
- 7.13. Corn Cobs, Stalks, Leaves, and Other Debris Are Found in Grain Tank
- 8. Storage
- 8.1. After the End of Harvest Season
- 8.2. Before the Start of Harvest Season
- 9. Technical Parameters
- 9.1. Technical Parameters
- 9.2. Unified Inch Bolt and Screw Torque Values
- 9.3. Metric Bolt and Screw Torque Values
