Description
-
Model List:
- 2680H Disk 3-Point
- 1. Introduction
- 1.1. Foreword
- 1.2. A Message to Our Customers
- 1.3. Recognize Safety Information
- 1.4. Understand Signal Words
- 1.5. Follow Safety Instructions
- 1.6. Spanish Safety Signs and Operators Manual
- 1.7. Prepare for Emergencies
- 1.8. Wear Protective Clothing
- 1.9. Protect Against Noise
- 1.10. Practice Safe Maintenance
- 1.11. Park Machine Safely
- 1.12. Support Raised Equipment
- 1.13. Remove Paint Before Welding or Heating
- 1.14. Avoid Heating Near Pressurized Fluid Lines
- 1.15. Avoid HighPressure Fluids
- 1.16. Inspect Lift Circuit Hoses
- 1.17. Store Attachments Safely
- 1.18. Service Tires Safely
- 1.19. Decommissioning Proper Recycling and Disposal of Fluids and Components
- 1.20. Handle Chemical Products Safely
- 1.21. Operate Safely
- 1.22. NonPermissible Use
- 1.23. Use Safety Lights and Devices
- 1.24. Keep Riders Off Machine
- 1.25. Observe Maximum Transport Speed
- 1.26. Use a Signal Person
- 1.27. Use a Safety Chain
- 1.28. Tow Loads Safely
- 1.29. Avoid Overhead Power Lines
- 1.30. Prepare for Transport
- 1.31. Transport Safely
- 2. Safety Signs
- 2.1. Replace Safety Signs
- 2.2. Safety Signs
- 2.3. Information Sign
- 3. Safety Features
- 3.1. Safety Features
- 4. Preparing Machine
- 4.1. Unload 2680H Disk 3Point Machine
- 4.2. Preparing Machine Checklist
- 5. Preparing Tractor
- 5.1. Use Tractor Operators Manual
- 5.2. Determine Tractor Requirements
- 5.3. Power TakeOff
- 5.4. Prepare Hydraulic SystemJohn Deere R/RT Series Tractors
- 5.5. Positioning Drawbar
- 5.6. Positioning Sway Blocks
- 5.7. Link Lengths
- 5.8. Changing Lateral Float
- 5.9. Adjusting Rate of Drop
- 5.10. Using Load/Depth Control
- 5.11. Determine Tractor Ballast Requirements
- 5.12. Rear Implement Weight Chart
- 6. Attaching and Detaching
- 6.1. Use Your Tractor and Tillage Equipment Operators Manuals
- 6.2. Attach Machine to Tractor
- 6.3. Use External Raise/Lower Switch
- 6.4. Make Proper Hose Connections
- 6.5. Detach from Tractor
- 7. Transporting Machine
- 7.1. Use Safety Lights and Devices
- 7.2. Observe Maximum Transport Speed
- 7.3. Tow Loads Safely
- 7.4. Avoid Overhead Power Lines
- 7.5. Prepare for Transport
- 7.6. Transport Safely
- 7.7. Rear Hitch Lock/Damping
- 7.7.1. Hitch Damping
- 8. Operating Machine
- 8.1. Before Entering Field Guidelines
- 8.2. InField Operation
- 8.3. Tighten Hardware
- 8.4. Use Operators Manual Holder
- 8.5. Prepare to Operate in FieldJohn Deere R/RT Series Tractors
- 8.6. Adjust Soil Deflector
- 8.7. Adjust Scrapers
- 9. Lubrication and Maintenance
- 9.1. Use Safe Service Procedures
- 9.2. Multipurpose Extreme Pressure (EP) Grease
- 9.3. Alternative and Synthetic Lubricants
- 9.4. Lubricant Storage
- 9.5. Beginning and End of Season
- 9.6. Lubrication Symbols
- 9.7. Lubrication and Maintenance Intervals
- 10. Troubleshooting
- 10.1. Troubleshooting Guidelines
- 10.2. Troubleshoot Field Problems
- 11. Service
- 11.1. Practice Safe Maintenance
- 11.2. Use Safe Service Procedures
- 11.3. Work in Clean Area
- 11.4. Service Machines Safely
- 11.5. Support Machine Properly
- 11.6. Avoid HighPressure Fluids
- 11.7. Replace Hydraulic Hoses
- 11.8. Place Machine In Service Position
- 11.9. Tighten Hardware
- 11.10. Sharpen Sweeps and Disks
- 11.11. Metric Bolt and Screw Torque Values
- 11.12. Unified Inch Bolt and Screw Torque Values
- 11.13. Face Seal Fittings Assembly and InstallationAll Pressure Applications
- 11.13.1. Face Seal ORing to Stud End Installation
- 11.13.2. Face Seal Adjustable Stud End ORing Installation
- 11.13.3. Face Seal Straight Stud End ORing Installation
- 11.13.4. Fitting Installation
- 11.13.5. Assembly Torque
- 11.14. Metric Face Seal and ORing Stud End Fitting Torque ChartStandard Pressures
- 11.15. SAE Face Seal and ORing Stud End Fitting Torque ChartStandard Pressures
- 11.16. Check Pivot Bushings
- 11.17. Replace Pivot Bushings
- 11.18. Check Disk Shank Cord Alignment
- 11.19. Service Disks and Hubs
- 11.20. Service Disk Shanks
- 11.21. Inspect Disk Shank Cords
- 11.22. Service Roller and Cradle
- 11.23. Replace Scrapers
- 11.24. When to Change Disk Blades
- 11.25. Identify Disk Blades Eligible for Warranty
- 12. Storage
- 12.1. Beginning of Season Service
- 12.2. End of Season Service
- 13. Specifications
- 13.1. Tractor Engine Power Requirements
- 13.2. Machine Weight
- 13.3. Transport Width
- 13.4. Ground Engaging
- 13.5. Disk Blades
- 13.6. Hydraulic Cylinders
- 13.7. Hydraulic Requirements
- 13.8. Product Identification Number
- 14. John Deere Service Literature Available
- 14.1. Technical Information
- 15. John Deere Service Keeps You On Job
- 15.1. John Deere Is At Your Service
