John Deere 600 F and 600 R Series Cutting Platform Operator Manual OMHXE23101

Description

• Model List:
  • 600 F Series Cutting Platform
  • 600 R Series Cutting Platform

• 1. Contents
• 1.1. Safety Features
• 1.1.1. Platform Safety Features
• 1.1.2. Recognize Safety Information
• 1.1.3. Understand Signal Words
• 1.1.4. Follow Safety Instructions
• 1.1.5. Practice Safe Maintenance
• 1.1.6. Prepare for Emergencies
• 1.1.7. Wear Protective Clothing
• 1.1.8. Guards and Shields
• 1.1.9. Stay Clear of Harvesting Units
• 1.1.10. Keep Hands Away From Knives
• 1.1.11. Stay Clear of Rotating Drivelines
• 1.1.12. Stay Clear of Cutterbar When Rotating Auger
• 1.1.13. Service Belts Safely
• 1.1.14. Service Machines Safely
• 1.1.15. Support Machine Properly
• 1.1.16. Protect Against High Pressure Spray
• 1.1.17. Remove Paint Before Welding or Heating
• 1.1.18. Avoid Heating Near Pressurized Fluid Lines
• 1.1.19. Avoid Contact With Moving Parts
• 1.1.20. Avoid HighPressure Fluids
• 1.1.21. Dispose of Waste Properly
• 1.1.22. Store Attachments Safely
• 1.1.23. Use Safety Lights and Devices
• 1.1.24. Transport Combine With Header Safely
• 1.1.25. Road Transport Disconnect Switch (Black)
• 1.1.26. Ballasting for Safe Ground Contact
• 1.1.27. Parking and Leaving the Combine
• 1.1.28. Replace Safety Signs
• 1.2. Safety Sign Location
• 1.2.1. Safety Sign Location
• 1.3. Transporting
• 1.3.1. Transporting
• 1.4. Attaching and Detaching
• 1.4.1. Rear Auger Stripper Extension Location
• 1.4.2. Attaching Platform to Combine
• 1.4.3. Leveling Platform Without ContourMaster
• 1.4.4. Detaching Platform from Combine
• 1.4.5. Feeder House Latching Pins (Cleanout)
• 1.4.6. Feeder House Manual Unlatching
• 1.4.7. Latching Cable Shear Screw Location
• 1.4.8. Single Point LatchingAdjusting
• 1.4.9. Level Land Feeder House Lower End CableAdjusting
• 1.5. Attaching Platform to Pre 60 Series Combines
• 1.5.1. Attaching/Detaching Platform to Pre 60 Series Combine
• 1.5.2. Manual Latch Feeder House Pins
• 1.5.3. Wedge Kit
• 1.5.4. DIALAMATIC DIALAMATIC is a trademark of Deere Company. He
• 1.5.5. HYDRAFLEXHYDRAFLEX is a trademark of Deere Company Operation
• 1.6. Calibration and Programming
• 1.6.1. When to Calibrate
• 1.6.2. Armrest Functions
• 1.6.3. Active Header Control Display
• 1.6.4. Description of Automatic Header Height Control System
• 1.6.5. Calibration Error Codes
• 1.6.6. User Calibration Procedures for 70 Series Combines
• 1.6.7. User Calibration Procedures for 50/60 Series Combines
• 1.7. Operating the Platform
• 1.7.1. Cutting Platform Operation
• 1.7.2. Setting Backshaft Speed
• 1.7.3. Position Warning Lights for Field Operation
• 1.7.4. Cutting Platform Controls
• 1.7.5. Feeder House Rate/Sensitivity Adjust Switch
• 1.7.6. Adjusting Platform Drop Rate
• 1.7.7. Operating HYDRAFLEXHYDRAFLEX is a trademark of Deere Company
• 1.7.8. Header Height/HydraFlex HydraFlex is a trademark of Deere Comp
• 1.7.9. Header Height Sensing HYDRAFLEX Heads with Auxiliary Sensors
• 1.7.10. Operating Flex Platform In Rigid Mode
• 1.7.11. Platform Tilt Position
• 1.7.12. Cutterbar Pressure Manual Adjust Switch (Black)
• 1.7.13. Harvesting SoybeansFlex Platforms
• 1.7.14. Harvesting Oats, Sorghum, Wheat and Sunflowers in Dry Ground Con
• 1.7.15. Harvesting Oats, Sorghum and Wheat in Damp or in Wet/Weedy Condi
• 1.7.16. Harvesting Oats, Sorghum, Barley and Wheat in Short, Thin Crops
• 1.7.17. Harvesting RiceRigid Platforms
• 1.8. Attachments and Options
• 1.8.1. Rear Auger Stripper and Flight Extensions for 9560/70 STS Combin
• 1.8.2. Auger Flight Extensions Flex Platform Only (Attachment)
• 1.8.3. Auger Speed Increase or Decrease (Attachment)
• 1.8.4. Stubble Lights (Attachment)
• 1.8.5. Heavy Duty Wear PlatesRigid Platform Only (Optional)
• 1.8.6. Auxiliary Header Height Control Sensors Rigid Platform (Option
• 1.8.7. Auxiliary Header Height Control SensorsFlex Platform (Optional)
• 1.8.8. Crop Lifters Rigid Platform Only (Attachment)
• 1.8.9. Spare Knife Storage (Optional)
• 1.8.10. Fine Serrated Knife for Flex Platform (Optional)
• 1.8.11. Knife Assemblies with LongShort Sections (Optional)
• 1.8.12. Knife Drive Sheaves (Attachment)
• 1.8.13. Auger AntiWrap Shields Rigid Platforms Only (Attachment)
• 1.8.14. Reel Position Resume (Attachment)
• 1.8.15. Additional Floor Stripper (Attachment)
• 1.8.16. Reel Relief (Attachment)
• 1.8.17. Short Dividers Flex Platform Only (Attachment)
• 1.8.18. Low Stone Dam (Attachment or Option)
• 1.8.19. High Stone Dam (Attachment or Option)
• 1.8.20. Raised Height Skid Shoes Flex Platform Only (Optional)
• 1.9. Adjustments Flex Platform
• 1.9.1. Bleeding HydraFlex System
• 1.9.2. Standard PermaGlide Divider and Divider Point
• 1.9.3. Height Adjustment of PermaGlide Divider Assembly
• 1.9.4. SidetoSide Adjustment of PermaGlide Divider Assembly
• 1.10. Adjustments Rigid Platform
• 1.10.1. Cutterbar Positions
• 1.10.2. Adjusting Cutterbar Position
• 1.10.3. Crop Lifter Adjustments
• 1.11. Adjustments Auger and Stripper
• 1.11.1. Remove Knife Drive Belt From Drive Sheave
• 1.11.2. Adjusting Auger Position
• 1.11.3. Adjusting Auger Height
• 1.11.4. Adjusting Auger Fore/Aft
• 1.11.5. Adjusting Center Auger Finger Timing
• 1.11.6. Adjusting Rear Stripper
• 1.11.7. Adjusting Rear Floor Stripper
• 1.11.8. Adjusting Front Floor Strippers
• 1.11.9. Adjusting Auger Chain
• 1.12. Adjustments Reel
• 1.12.1. Adjusting Reel Fingers
• 1.12.2. Adjusting Reel Height
• 1.12.3. Adjusting Reel Fore/Aft and Lift Cylinders
• 1.12.4. Rephasing Reel Fore/Aft Cylinders
• 1.12.5. Rephasing Reel Lift Cylinders
• 1.12.6. Bleeding the Reel Lift Cylinder System
• 1.12.7. DIALASPEEDDIALASPEED is a trademark of Deere Company
• 1.12.8. Reel Speed or Belt Pickup Speed Dial (Black) for 70 Series Combi
• 1.12.9. Adjusting Reel Speed Ratio Sensor
• 1.12.10. Adjusting Reel Drive Gear
• 1.13. Lubrication
• 1.13.1. Alternative and Synthetic Lubricants
• 1.13.2. Mixing of Lubricants
• 1.13.3. Lubricant Storage
• 1.14. Lubrication and Maintenance
• 1.14.1. Lubrication Interval Chart
• 1.14.2. Care and Maintenance of Belts
• 1.14.3. Every 50 Hours of Operation
• 1.14.4. Every 200 400 Hours of Operation
• 1.15. Troubleshooting
• 1.15.1. Cutting Platform
• 1.15.2. ACTIVE HEADER CONTROLACTIVE HEADER CONTROL is a trademark of Dee
• 1.16. Service
• 1.16.1. Safe Cutting Platform Operation
• 1.16.2. Feeder House and Reel Safety Stops
• 1.16.3. Opening and Closing Right and LeftHand Shields
• 1.16.4. Remove and Install Knife Drive Belt
• 1.16.5. Adjusting Knife Drive Belt Tension
• 1.16.6. Replacing Cutterbar Knife
• 1.16.7. Aligning Knife
• 1.16.8. Adjusting Knife Fore/Aft Clearances
• 1.16.9. Adjusting Knife Vertical Clearance
• 1.16.10. Knife HoldDown Clearance
• 1.16.11. Replacing Knife Sections
• 1.16.12. Replacing Auger Fingers and Retainers
• 1.16.13. Stubble Light Bulb Replacement
• 1.16.14. Header Warning Light Bulb Replacement
• 1.17. Storage
• 1.17.1. End of Season Service
• 1.17.2. Beginning of Season Service
• 1.18. Specifications
• 1.18.1. SpecificationsRigid Platforms
• 1.18.2. Dimensions/WeightsRigid Platforms
• 1.18.3. SpecificationsFlex Platforms
• 1.18.4. Dimensions/WeightsFlex Platforms
• 1.18.5. Product Identification Number
• 1.18.6. Keep Machines Secure
• 1.18.7. Keep Proof of Ownership
• 1.18.8. Unified Inch Bolt and Screw Torque Values
• 1.18.9. Metric Bolt and Screw Torque Values
• 1.19. John Deere Service Literature Available
• 1.19.1. Technical Information
• 1.20. John Deere Service Keeps You On The Job
• 1.20.1. John Deere Is At Your Service
• 2. Page Number
• 2.1. Section 05
• 2.2. Section 10
• 2.3. Section 15
• 2.4. Section 20
• 2.5. Section 25
• 2.6. Section 30
• 2.7. Section 35
• 2.8. Section 40
• 2.9. Section 45
• 2.10. Section 50
• 2.11. Section 55
• 2.12. Section 60
• 2.13. Section 65
• 2.14. Section 70
• 2.15. Section 75
• 2.16. Section 80
• 2.17. Section 85
• 2.18. Section 90
• 2.19. Section 95