John Deere 600 Series Flexible and Rigid CutteRHead Operator Manual OMCQ71580

Description

• Model List:
  • 600 Series Flexible and Rigid CutteRHead

• 1. Introduction
• 1.1. Foreword
• 1.2. Company Info
• 1.3. Interpreting Machine Serial Number
• 2. Identification View
• 2.1. Identification View
• 3. Safety Features
• 3.1. Safety Features Rigid and Flexible 600
• 3.2. Recognize Safety Information
• 3.3. Understand Signal Words
• 3.4. Follow Safety Instructions
• 3.5. Replace Safety Signs
• 3.6. Operator Ability
• 3.7. Ballasting for Safe Ground Contact
• 3.8. Parking and Leaving the Machine
• 3.9. Prepare for Emergencies
• 3.10. Wear Protective Clothing
• 3.11. Stay Clear of Harvesting Units
• 3.12. Keep Hands Away From Knives
• 3.13. Use Safety Lights and Devices
• 3.14. Safely Transporting the Combine with Header
• 3.15. Respect the Traffic Regulations
• 3.16. Road Transport Disconnect Switch
• 3.17. Practice Safe Maintenance
• 3.18. Remove Paint Before Welding or Heating
• 3.19. Avoid Heating Near Pressurized Fluid Lines
• 3.20. Avoid Entanglement
• 3.21. Avoid Contact With Moving Parts
• 3.22. Stay Clear of Cutterbar When Rotating Auger
• 3.23. Stay Clear of Rotating Drivelines
• 3.24. Guards and Shields
• 3.25. Avoid HighPressure Fluids
• 3.26. Service Accumulator Systems Safely
• 3.27. Service Machines Safely
• 3.28. Service Belts Safely
• 3.29. Decommissioning Proper Recycling and Disposal of Fluids and Components
• 3.30. Support Machine Properly
• 3.31. Store Attachments Safely
• 4. Safety Warnings
• 4.1. Pictorial Safety Signs
• 4.2. Replace Safety Signs
• 4.3. Recognize Safety Information
• 4.4. Operators Manual
• 4.5. Hydraulic Pressure
• 4.6. Telescoping Driveline
• 4.7. Reel Safety Stops
• 4.8. Reel Drive
• 4.9. Cutterbar Movement
• 4.10. Entanglement in the Header
• 5. Coupling and Decoupling
• 5.1. Checking Auger Stripper Location
• 5.2. Identification of Type
• 5.3. Coupling Header to CombineAType
• 5.4. Coupling Header to CombineBType
• 5.5. Coupling Header to CombineCType
• 5.6. Removing Header from Feeder HouseAType
• 5.7. Removing Header from Feeder HouseBType
• 5.8. Removing Header from Feeder HouseCType
• 5.9. Unlocking Feeder House Manually AType
• 5.10. Unlocking Feeder House Manually BType
• 5.11. Unlocking Feeder House ManuallyCType
• 5.12. Shear Screw Location
• 6. Transport
• 6.1. Transport
• 7. Operating the Header
• 7.1. Choice of Harvesting Time
• 7.2. Cutting Platform Operation
• 7.2.1. Cutting Height
• 7.3. Operating Flexible Headers HYDRAFLEX System Pressure
• 7.4. Checking Platform Speeds
• 7.5. Reel Operation
• 7.6. Cutting Platform Controls
• 7.7. Combining Oats, Sorghum, Wheat and Sunflowers in Dry Ground Conditions
• 7.8. Combining Oats, Sorghum and Wheat in Damp or Wet Ground Conditions
• 7.9. Combining Oats, Sorghum, Barley and Wheat in Short, Thin CropsRigid Platforms
• 7.10. Combining RiceRigid Platforms
• 7.11. Combining SoybeansFlex Platforms
• 8. Accessories and Optional Equipment
• 8.1. Auger Flight Extensions (Attachment)Flex Platforms
• 8.2. Auger Speeds (Attachment)
• 8.3. Heavy Duty Wear Plates (Optional)Rigid Platforms
• 8.4. Reel Position Resume (Attachment)STS Combines
• 8.5. Short Dividers, Flex Header
• 9. Calibration Procedures
• 9.1. Calibration Procedures
• 10. Adjusting Flexible Headers
• 10.1. Adjust Platform Cutterbar/Skid Plate Tilt (Flex)
• 10.2. Operating Flex Header In Rigid Mode
• 10.3. Adjusting Head Drop Rate
• 10.4. Standard PERMAGLIDE Divider Points
• 10.5. Height Adjustment of Standard PERMAGLIDE Divider Points
• 10.6. SidebySide Adjustment of the Front Section of the Standard PERMAGLIDE Point
• 11. Adjusting Rigid Headers
• 11.1. Cutterbar Positions
• 11.2. Adjusting Cutterbar Fore/Aft
• 11.3. Adjusting Platform Cutterbar/Skid Plate Tilt (Rigid)
• 11.4. Adjusting Head Drop Rate
• 12. Adjusting the Auger and Stripper
• 12.1. Setting Reel Safety Stops
• 12.2. Adjusting Auger Clearance
• 12.3. Adjusting auger height
• 12.4. Adjusting Auger Fore/Aft
• 12.5. Adjusting Auger Center Finger Synchronization
• 12.6. Adjusting Rear Auger Stripper
• 12.7. Adjusting Lower Stripper
• 12.8. Adjusting Auger Chain
• 13. Adjusting the Reel
• 13.1. Adjusting Reel Fingers
• 13.2. Adjusting the Reel Position
• 13.3. Adjusting Width Between Reel Arms
• 13.4. Adjusting Reel Fore/Aft and Lift Cylinders
• 13.5. Rephase Hydraulic Reel Fore/Aft
• 13.6. Rephasing Reel Lift Cylinders
• 13.7. Bleeding the Reel Lift Cylinder System
• 13.8. Adjusting Reel Speed Ratio Sensor
• 13.9. Adjusting Platform Height Restoring System
• 14. Lubricants
• 14.1. Gear Oil
• 14.2. Alternative and Synthetic Lubricants
• 14.3. Mixing of Lubricants
• 14.4. Lubricant Storage
• 15. Lubrication and Service
• 15.1. Lubrication Symbols
• 15.2. Care and Maintenance of Belts
• 16. Troubleshooting
• 16.1. Cutterbar Difficulties
• 16.2. Down and Tangled Crops Difficulties
• 16.3. Feeder House Difficulties
• 16.4. Auger Difficulties
• 16.5. Cutting Difficulties
• 16.6. Reel Difficulties
• 16.7. Hydraulic System Difficulties
• 16.8. ACTIVE HEADER CONTROL
• 17. Servicing
• 17.1. Safe Cutting Platform Operation
• 17.2. Removal and Installation of the Cutting Bar Drive Belt
• 17.2.1. Rigid Headers
• 17.2.2. Flex Headers
• 17.2.3. Adjusting Knife Drive Belt Tension
• 17.3. Replacing the Cutterbar Knife
• 17.4. Aligning Knife Head / Knife Drive
• 17.5. Knife HoldDown Clearance
• 17.6. Replacing Knife Sections
• 17.7. Replacing Auger Fingers and Retainers
• 17.8. HydraFlex System Bleeding Flexible Headers
• 18. Storage
• 18.1. End of Season Service
• 18.2. Beginning of Season Service
• 19. SPECIFICATIONS
• 19.1. SpecificationsRigid Headers
• 19.2. Dimensions/WeightsRigid Headers
• 19.3. SpecificationsFlex Platforms
• 19.4. Dimensions/WeightsFlex Cutting Platforms
• 19.5. Product Identification Number
• 19.6. Metric Bolt and Screw Torque Values
• 19.7. Unified Inch Bolt and Screw Torque Values
• 20. John Deere Service Literature Available
• 20.1. Technical Information
• 21. John Deere Service Keeps You on the Job
• 21.1. John Deere Parts
• 21.2. The Right Tools
• 21.3. WellTrained Technicians
• 21.4. Prompt Service