Description
-
Model List:
- 740 Classic Loader
- 1. Contents
- 1.0.1. Recognize Safety Information
- 1.0.2. Understand Signal Words
- 1.0.3. Follow Safety Instructions
- 1.0.4. Protect People and Animals
- 1.0.5. Avoid Injury or Death from Rollover Accidents
- 1.0.6. Avoid Power Lines
- 1.0.7. Dig Safely
- 1.0.8. Use Correct Lift Cylinder Position
- 1.0.9. Detach Loader Safely
- 1.0.10. Avoid Injury or Death from Falling Round Bales
- 1.0.11. Keep Riders Off Machine
- 1.0.12. Operate Bucket/Attachment Safely
- 1.0.13. Carry Materials Safely
- 1.0.14. Safe Loader Operation on Slopes
- 1.0.15. Driving on Public Roads
- 1.0.16. Service Loader Safely
- 1.0.17. Check Hoses for Damage
- 1.0.18. Avoid HighPressure Fluids
- 1.0.19. Store Attachments Safely
- 1.0.20. Replace Safety Signs
- 1.0.21. Safety Sign Locations
- 1.1. Prepare the Tractor
- 1.1.1. Approved Tractors
- 1.1.2. Front Tire Tread Setting and Fender Compatibility (MFWD Tractor)
- 1.1.3. Front Tire Load Index and Rear Ballast RequirementsSelfLevelin
- 1.1.4. Front Tire Load Index and Rear Ballast RequirementsNonSelf Lev
- 1.1.5. Removing Front Weights
- 1.1.6. Adjusting Front Tread Settings2Wheel Drive and HFWD Tractors
- 1.1.7. Adjusting Front Tread Settings/Steering Stops30, 40, 50, 55 Ser
- 1.1.8. Adjusting Front Tread Settings/Steering Stops6000 and 7000 Seri
- 1.1.9. MFWD Tire/Fender Interference with Loader
- 1.1.10. Adjusting Front Fenders (30, 40, 50 and 55 MFWD Row Crop Tractor
- 1.1.11. Rear Tread Settings
- 1.1.12. Adjusting Timed Detent
- 1.1.13. Adjusting Flow Rate
- 1.1.14. Setting Control Lever Stops (30, 40, 50 and 55 Series Tractors)
- 1.2. Controls
- 1.2.1. Operating Loader with Selective Control Valve (SCV) Levers
- 1.2.2. Operating Loader with MultiFunction Control Lever
- 1.3. Detach Loader
- 1.3.1. Detach Loader
- 1.4. Attach Loader
- 1.4.1. Attach Loader
- 1.5. Transport
- 1.5.1. Carrying Loads
- 1.5.2. Keep Riders Off Machine
- 1.5.3. Driving on Public Roads
- 1.6. Operate Loader
- 1.6.1. Check Lift Cylinder Position
- 1.6.2. Install Lift Cylinder Stops
- 1.6.3. Raising and Lowering Loader
- 1.6.4. Removing Material from a Pile
- 1.6.5. Dumping Bucket
- 1.6.6. Digging
- 1.6.7. Leveling Bucket with Bucket Level Indicator (If Equipped)
- 1.6.8. Leveling and Scraping Forward
- 1.6.9. Leveling in Reverse
- 1.6.10. Detach Bucket or Attachment
- 1.6.11. Attach Bucket or Attachment
- 1.6.12. Attachments Available
- 1.7. Lubrication and Maintenance
- 1.7.1. Lubricate and Service Loader Safely
- 1.7.2. Perform Lubrication and Maintenance
- 1.7.3. Observe Lubrication Symbols
- 1.7.4. Alternative and Synthetic Lubricants
- 1.7.5. First 10 Hours
- 1.7.6. Every 10 Hours
- 1.7.7. Every 50 Hours
- 1.8. Service
- 1.8.1. Servicing Loader and/or Tractor Safely (Loader Attached)
- 1.8.2. Keep Service Area Clean
- 1.8.3. Avoid HighPressure Fluids
- 1.8.4. ORing Installation
- 1.8.5. Tightening Procedure for Fittings
- 1.8.6. Replacing Hydraulic Hoses, Couplers, Tubing, or Connectors
- 1.8.7. Accessing Front of Tractor
- 1.8.8. Identifying Hose ConnectionsLoader to Tractor Selective Control
- 1.8.9. Identifying Hose ConnectionsLoader to MidMount Couplers (6000
- 1.8.10. Identifying Hose ConnectionsLoader to MidMount Valve (30, 40,
- 1.8.11. Identifying Hose ConnectionsLoader to MultiCoupler (6000 and 7
- 1.8.12. Adjust QUIKCHANGE Latch Plates
- 1.8.13. Adjust Wedge Mounting FrametoMast
- 1.8.14. Metric Bolt and Screw Torque Values
- 1.8.15. Unified Inch Bolt and Screw Torque Values
- 1.9. Assembly
- 1.9.1. Perform Predelivery Service Safely
- 1.9.2. Installation Instructions Available Online to John Deere Dealers
- 1.9.3. Recommended Set Up/Assembly Sequence
- 1.9.4. Prepare the Tractor
- 1.9.5. Prepare the Loader
- 1.9.6. Position Loader on Mounting Frames
- 1.9.7. Install Bucket/Attachment
- 1.9.8. Final Inspection and Adjustments
- 1.9.9. Install Optional Equipment/Attachments
- 1.10. John Deere Service Keeps You On The Job
- 1.10.1. John Deere Is At Your Service
- 2. Page Number
- 2.1. Section 05
- 2.2. Section 10
- 2.3. Section 15
- 2.4. Section 20
- 2.5. Section 25
- 2.6. Section 30
- 2.7. Section 35
- 2.8. Section 40
- 2.9. Section 45
- 2.10. Section 50
