Description
-
Model List:
- 913 V-Ripper
- 1. Introduction
- 1.1. Foreword
- 1.2. Identification View
- 1.3. A Message to Our Customers
- 1.4. Preliminary Checks
- 1.5. Regions and Country Versions
- 1.6. Machine Overview
- 1.7. Recognize Safety Information
- 1.8. Understand Signal Words
- 1.9. Follow Safety Instructions
- 1.10. Use Seat Belt Properly
- 1.11. Park Machine Safely
- 1.12. Keep Riders Off Machine
- 1.13. Prepare for Emergencies
- 1.14. Use Safety Lights and Devices
- 1.15. Wear Protective Clothing
- 1.16. Use a Safety Chain
- 1.17. Tow Loads Safely
- 1.18. Observe Maximum Transport Speed
- 1.19. Practice Safe Maintenance
- 1.20. Remove Paint Before Welding or Heating
- 1.21. Avoid HighPressure Fluids
- 1.22. Store Attachments Safely
- 2. Safety Signs
- 2.1. Read Safety Signs Carefully
- 2.2. Safety Signs
- 3. Preparing the Tractor
- 3.1. Recommended Tractor Power
- 3.2. Position Drawbar
- 3.3. Adjusting Tractor Hitch
- 3.4. Checking Ballast, Wheel Spacing, and Tire Inflation
- 3.5. Tractor Brakes
- 4. Preparing the Machine
- 4.1. Checking and Lubricating Machine
- 4.2. Tightening Hardware
- 4.3. Standards
- 5. Operating the Machine
- 5.1. Following Safe Operating Procedures
- 5.2. Leveling (SidetoSide) Integral VRipper
- 5.3. Leveling (FronttoRear) Integral VRipper
- 5.4. Preparing Ripper for Operation
- 5.5. Resetting Standards
- 5.6. Adjusting Trip Force (SpringReset Rock Standard)
- 5.7. Adjusting CushionTrip Standard
- 6. Attaching and Detaching
- 6.1. Attaching Machine Safely
- 6.2. Setting Rockshaft Selector Lever
- 6.3. Using External Raise/Lower Switch
- 6.4. Attaching Machine to Tractor
- 6.5. Detaching Integral VRipper (With Support Stands)
- 6.6. Detaching Integral VRipper (Without Support Stands)
- 7. Transporting
- 7.1. Use a Safety Chain
- 7.2. Use Safety Lights and Devices
- 7.3. Tow Loads Safely
- 7.4. Observe Maximum Transport Speed
- 7.5. Integral VRippers
- 8. Assembly
- 8.1. Put Mainframe on Stands
- 8.2. Attach Center Standard
- 8.3. Attach Center Standard (SafetyTrip or SpringReset Rock)
- 8.4. Tighten Center Standard Hardware (SafetyTrip or SpringReset)
- 8.5. Attach Outer Standards
- 8.6. Attach Lower Standard
- 8.7. Position Shank (CushionTrip Standard)
- 8.8. Attach Support Stands
- 9. Troubleshooting
- 9.1. Troubleshooting
- 10. Lubrication and Maintenance
- 10.1. Multipurpose Extreme Pressure (EP) Grease
- 10.2. Alternative Lubricants
- 10.3. Lubricant Storage
- 10.4. Waste Oil
- 10.5. Lubrication Symbols
- 10.6. Lubrication Intervals
- 10.7. SafetyTrip Standards
- 10.8. SpringReset Rock Standard (Optional)
- 10.9. Lubricate CushionTrip Standards
- 11. Service
- 11.1. Keep Service Area Clean
- 11.2. Using Safe Service Procedures
- 11.3. Metric Bolt and Screw Torque Values
- 11.4. Unified Inch Bolt and Screw Torque Values
- 11.5. Optional Ripper Points
- 11.6. Replacing SlipOn Point
- 11.7. Replacing Ripper Point
- 11.8. Replacing Cast EXTREME LASERRIP Ripper Points
- 11.9. Shear Bolt Standards
- 11.10. Replacing Springs on SpringReset Rock Standard
- 12. Storage
- 12.1. Storing VRipper
- 12.2. Removing the VRipper from Storage
- 13. Specifications
- 13.1. General
- 13.2. Transport Width
- 13.3. Working Width
- 13.4. Tractor Power Recommendations
- 13.5. Machine Weights
- 13.6. Leveling Integral Ripper
- 13.7. Product Identification Number
- 13.7.1. Content of Individual Positions or Group of Position Character Products Serial Number
- 13.8. Keep Proof of Ownership
- 13.9. Keep Machines Secure
- 14. John Deere Service Keeps You On Job
- 14.1. John Deere Is At Your Service
- 14.2. John Deere Parts
- 14.3. The Right Tools
- 14.4. WellTrained Technicians
- 14.5. Prompt Service
