John Deere 913 V-Ripper Operator Manual OMP75195

Description

• Model List:
  • 913 V-Ripper

• 1. Contents
• 1.0.1. Recognize Safety Information
• 1.0.2. Understand Signal Words
• 1.0.3. Follow Safety Instructions
• 1.0.4. Operate Safely
• 1.0.5. Avoid Power Lines
• 1.0.6. Keep Riders Off Machine
• 1.0.7. Prepare for Emergencies
• 1.0.8. Wear Protective Clothing
• 1.0.9. Use Seat Belt Properly
• 1.0.10. Operate the Ripper Safely
• 1.0.11. Use Safety Lights and Devices
• 1.0.12. Practice Safe Maintenance
• 1.0.13. Safe Transport of the Ripper
• 1.1. Safety Signs
• 1.1.1. Read Safety Signs Carefully
• 1.1.2. Safety Signs
• 1.1.3. Locate the Stand Support in the Correct Position
• 1.2. Identification View
• 1.2.1. Identification View
• 1.3. Preparing Tractor
• 1.3.1. Recommended Tractor Power
• 1.3.2. Position Drawbar
• 1.3.3. Adjusting Tractor Hitch
• 1.3.4. Checking Ballast, Wheel Spacing, and Tire Inflation
• 1.3.5. Tractor Brakes
• 1.4. Preparing Machine
• 1.4.1. Checking and Lubricating Machine
• 1.4.2. Tightening Hardware
• 1.4.3. Standards
• 1.5. Attaching and Detaching
• 1.5.1. Attaching Machine Safely
• 1.5.2. Setting Rockshaft Selector Lever
• 1.5.3. Using External Raise/Lower Switch
• 1.5.4. Attaching Machine to Tractor
• 1.5.5. Detaching Integral VRipper (With Support Stands)
• 1.5.6. Detaching Integral VRipper (Without Support Stands)
• 1.6. Transporting
• 1.6.1. Integral VRippers
• 1.7. Operating Machine
• 1.7.1. Following Safe Operating Procedures
• 1.7.2. Leveling (SidetoSide) Integral VRipper
• 1.7.3. Leveling (FronttoRear) Integral VRipper
• 1.7.4. Preparing Ripper for Operation
• 1.7.5. Resetting Standards
• 1.7.6. Adjusting Trip Force (SpringReset Rock Standard)
• 1.7.7. Adjusting CushionTrip Standard
• 1.8. Lubrication and Maintenance
• 1.8.1. Alternative Lubricants
• 1.8.2. Lubricant Storage
• 1.8.3. Waste Oil
• 1.8.4. Lubrication Symbols
• 1.8.5. Lubrication Intervals
• 1.8.6. SafetyTrip Standards
• 1.8.7. SpringReset Rock Standard (Optional)
• 1.8.8. Lubricate CushionTrip Standards
• 1.9. Troubleshooting
• 1.9.1. Troubleshooting
• 1.10. Service
• 1.10.1. Keep Service Area Clean
• 1.10.2. Using Safe Service Procedures
• 1.10.3. Metric Bolt and Screw Torque Values
• 1.10.4. Unified Inch Bolt and Screw Torque Values
• 1.10.5. Optional Ripper Points
• 1.10.6. Replacing SlipOn Point
• 1.10.7. Replacing Ripper Point
• 1.10.8. Replacing Cast EXTREME LASERRIPLASERRIP is a trademark of Deere Company. Ripper Points
• 1.10.9. Shear Bolt Standards
• 1.10.10. Replacing Springs on SpringReset Rock Standard
• 1.11. Assembly
• 1.11.1. Put Mainframe On Stands
• 1.11.2. Attach Center Standard
• 1.11.3. Attach Center Standard (SafetyTrip or SpringReset Rock)
• 1.11.4. Tighten Center Standard Hardware (SafetyTrip or SpringReset)
• 1.11.5. Attach Outer Standards
• 1.11.6. Attach Lower Standard
• 1.11.7. Position Shank (CushionTrip Standard)
• 1.11.8. Attach Support Stands
• 1.12. Storage
• 1.12.1. Storing VRipper
• 1.12.2. Removing the VRipper From Storage
• 1.13. Specifications
• 1.13.1. General
• 1.13.2. Transport Width
• 1.13.3. Working Width
• 1.13.4. Tractor Power Recommendations
• 1.13.5. Machine Weights
• 1.13.6. Leveling Integral Ripper
• 1.13.7. Product Identification Number
• 1.13.8. Keep Proof of Ownership
• 1.13.9. Keep Machines Secure
• 1.14. John Deere Service Literature Available
• 1.14.1. Technical Information
• 1.15. John Deere Service Keeps You On Job
• 1.15.1. John Deere Is At Your Service
• 2. Page Number
• 2.1. Section 05
• 2.2. Section 10
• 2.3. Section 15
• 2.4. Section 20
• 2.5. Section 25
• 2.6. Section 30
• 2.7. Section 35
• 2.8. Section 40
• 2.9. Section 50
• 2.10. Section 55
• 2.11. Section 60
• 2.12. Section 61
• 2.13. Section 65
• 2.14. Section 70