Description
-
Model List:
- AutoTrac Universal 300
- 1. Introduction
- 1.1. Foreword
- 1.2. John Deere Technical Information Bookstore
- 1.3. Read This Manual
- 1.4. Recognize Safety Information
- 1.5. Understand Signal Words
- 1.6. Follow Safety Instructions
- 1.7. Practice Safe Maintenance
- 1.8. Use Steps and Handholds Correctly
- 1.9. Handle Electronic Components and Brackets Safely
- 1.10. Use Electronic Display Properly
- 1.11. Operate Guidance Systems Safely
- 1.12. Use Seat Belt Properly
- 1.13. Operate AutoTrac Universal Safely
- 1.14. AutoTrac Universal 300 Machine Types
- 2. Safety Signs
- 2.1. Safety Warning AutoTrac Detected
- 2.2. Safety Warning Steering Calibration
- 3. Regulatory and Compliance Information
- 3.1. Federal Communications Commission Notification
- 3.2. Identify Date Code
- 3.3. EU Declaration of Conformity
- 3.4. UK Declaration of Conformity
- 3.5. Eurasian Economic UnionEAC
- 3.6. End User License Agreement
- 4. System Overview
- 4.1. Theory of Operation
- 4.2. AutoTrac Universal 300 Requirements
- 4.3. AutoTrac Accuracy
- 4.4. AutoTrac Status Pie
- 5. Component Overview
- 5.1. StarFire Receiver
- 5.2. GreenStar Display or Generation 4 Display
- 5.3. AutoTrac Universal 300
- 5.4. Road and Resume Switch
- 6. Setting Up
- 6.1. Configure AutoTrac Universal 300
- 6.2. Read and Accept Warning on GreenStar Display
- 6.3. GreenStar Display and Generation 4 Display Activations
- 6.4. StarFire Receiver Activations
- 6.5. StarFire Receiver Height, Fore/Aft, and Wheelbase
- 6.6. StarFire Measurements Table
- 6.7. Calibrate Terrain Compensation Module (TCM)
- 6.8. Enter Machine Information and Offsets
- 7. Setting UpAutoTrac Universal 300
- 7.1. Set Up System
- 7.2. Test Steering
- 7.3. Calibrate Steering Ratio
- 8. OperatingAutoTrac Universal 300
- 8.1. Create Guidance Line
- 8.2. Enable AutoTrac
- 8.3. Engage System
- 8.4. Disengage, Deactivate, and Disable System
- 9. OperatingOptimizing AutoTrac Universal 300
- 9.1. AutoTrac Settings
- 9.2. Optimize AutoTrac Performance
- 9.3. AutoTrac Limits
- 10. Troubleshooting
- 10.1. Diagnostic Readings
- 10.2. AutoTrac Status Tab
- 10.3. Motor Information Tab
- 10.4. Observable Symptoms
- 10.5. Disengage and Engage Thresholds
- 10.6. AutoTrac Universal 300 Diagnostic Addresses
- 10.7. AutoTrac Controller Diagnostic Trouble Codes
- 10.8. Stop CodesAutoTrac Universal 300
- 10.9. Guidance Warnings and InformationAutoTrac Universal 300
- 10.10. Trouble Code WarningsGuidance
- 10.11. AutoTrac Universal 300 Diagnostic Trouble Code Messages
- 11. Maintenance
- 11.1. Preseason Checklist
- 11.2. Postseason Checklist
- 11.3. Daily Checklist
- 12. John Deere Service Literature Available
- 12.1. Technical Information
- 13. John Deere Service Keeps You On Job
- 13.1. John Deere Is At Your Service
