Description
-
Model List:
- ExactDrop System
- 1. Introduction
- 1.1. Foreword
- 1.1.1. PreDelivery
- 1.1.2. Delivery
- 1.1.3. AfterSale
- 1.1.4. Owner Register
- 1.2. Recognize Safety Information
- 1.3. Understand Signal Words
- 1.4. Follow Safety Instructions
- 1.5. French and Spanish Safety Signs and Operators Manual
- 1.6. Wear Protective Clothing
- 1.7. Protect Against Noise
- 1.8. Practice Safe Maintenance
- 1.9. Avoid Backover Accidents
- 1.10. Park Machine Safely
- 1.11. Remove Paint Before Welding or Heating
- 1.12. Avoid Heating Near Pressurized Fluid Lines
- 1.13. Avoid HighPressure Fluids
- 1.14. Decommissioning Proper Recycling and Disposal of Fluids and Components
- 1.15. Handle Chemical Products Safely
- 1.16. Use Proper Tools
- 1.17. Work In Ventilated Area
- 1.18. Handling Batteries Safely
- 1.19. Remove Accumulated Crop Debris
- 1.20. Using Compressed Air For Cleaning
- 1.21. Maintain a Safe Area Around the Machine
- 1.22. Operator Ability
- 1.23. Observe Road Traffic Regulations
- 1.24. Check Machine Safety
- 1.25. Working Area
- 1.26. Before Operating
- 1.27. Operate Safely
- 1.28. Use Safety Lights and Devices
- 1.29. Keep Riders Off Machine
- 1.30. Instructional Seat
- 1.31. Use Steps and Handholds Correctly
- 1.32. Use Seat Belt Properly
- 1.33. Use Caution On Hillsides
- 1.34. Transport and Operate Safely
- 1.35. Transporting Machine Using Trailer
- 1.36. Prevent Machine Runaway
- 1.37. Handle Fuel SafelyAvoid Fires
- 1.38. Prepare for Emergencies
- 1.39. In Case of Fire
- 1.40. Handle Agricultural Chemicals Safely
- 1.41. Avoid Exposure To Chemicals
- 1.42. Clean Vehicle of Hazardous Chemicals, Including Pesticides
- 1.43. NonPermissible Use
- 1.44. Emergency Exit
- 2. Safety Signs
- 2.1. Replace Safety Signs
- 2.2. Chemical Exposure Decal
- 2.3. Agricultural Chemicals Decal
- 2.4. Tank Decal
- 2.5. Hydraulic Oil Under Pressure Decal
- 3. CommandCenter Display
- 3.1. Available Applications
- 3.2. Access Boom and Nozzles
- 3.3. Boom and Nozzles Main Page
- 3.4. Working Width
- 3.5. Nozzle Setup
- 3.6. Section Setup
- 3.7. Section Width Configurations
- 3.7.1. Section Valve Boom
- 3.7.2. ExactApply Boom (If Equipped)
- 4. Operate the Fertilizer Drops
- 4.1. Service and Operate Chemical Sprayers Safely
- 4.2. Avoid Exposure To Chemicals
- 4.3. Before Field Operation
- 4.4. Field Operation
- 5. ExactDrop System
- 5.1. Adjust Drag Hoses
- 5.2. Replace Fertilizer Drops
- 5.3. Install Metering Orifice Plates
- 5.4. Install Nozzle Extenders
- 5.5. Install PushtoConnect Elbows
- 5.6. Using the Multitool
- 5.7. Solution Flow Rates
- 5.8. ExactApply Setup (If Equipped)
- 5.8.1. Turret Nozzle Body Setup
- 5.8.2. Gen 4 Display Setup
- 5.9. Nozzle Spacing Layout
- 5.9.1. Total Application Width 152 cm (60 in)
- 5.9.2. Total Application Width 76 cm (30 in)
- 6. ExactDrop System Installation/Removal
- 6.1. ExactDrop System Installation and Removal
- 7. Lubrication and Maintenance
- 7.1. Clean Vehicle of Hazardous Chemicals, Including Pesticides
- 7.2. Dispose of Waste Properly
- 7.3. Service Intervals
- 7.4. Adjust Outer Breakaway Section SpringsAs Required
- 7.4.1. Adjust Breakaway Tension
- 7.5. Check Drag HosesYearly
- 7.6. Check Drag Hose Rubber GasketsYearly
- 7.7. Check HardwareYearly
- 7.8. Check Fertilizer Drop SleevesYearly
- 7.9. Inspect ExactDrop System StructureYearly
- 7.10. Clean ExactDrop System and Coat Exposed SurfacesYearly
- 8. Storage
- 8.1. Service and Operate Chemical Sprayers Safely
- 8.2. Avoid Exposure To Chemicals
- 8.3. Clean Vehicle of Hazardous Chemicals, Including Pesticides
- 8.4. Recommended Cleaners And Coatings
- 8.5. Prepare ExactDrop System for Storage
- 8.6. Remove ExactDrop System from Storage
- 9. Transporting
- 9.1. Transporting Machine with an Attachment
- 9.1.1. Loading
- 10. Specifications
- 10.1. Specifications
- 10.2. Dimensions
- 10.3. Unified Inch Bolt and Screw Torque Values
- 10.4. Metric Bolt and Screw Torque Values
- 10.5. Face Seal Fittings Assembly and InstallationAll Pressure Applications
- 10.5.1. Face Seal ORing to Stud End Installation
- 10.5.2. Face Seal Adjustable Stud End ORing Installation
- 10.5.3. Face Seal Straight Stud End ORing Installation
- 10.5.4. Fitting Installation
- 10.5.5. Assembly Torque
- 10.6. Metric Face Seal and ORing Stud End Fitting Torque ChartStandard Pressures
- 10.7. Metric Face Seal and ORing Stud End Fitting Torque ChartHighPressure Applications
- 10.8. SAE Face Seal and ORing Stud End Fitting Torque ChartStandard Pressures
- 10.9. SAE Face Seal and ORing Stud End Fitting Torque ChartHigh Pressure Applications
- 10.10. Four Bolt Flange Fittings Assembly and InstallationAll Pressure Applications
- 10.11. SAE Four Bolt Flange Cap Screw Torque ValuesStandard Pressure Applications
- 10.12. SAE Four Bolt Flange Cap Screw Torque ValuesHigh Pressure Applications
- 10.13. External Hexagon Port Plug Torque Chart
- 10.14. Product Warranty
- 11. John Deere Service Literature Available
- 11.1. Technical Information
- 12. John Deere Service Keeps You On The Job
- 12.1. John Deere Is At Your Service
