John Deere FL100 Directional Felling Head Operator Manual OMT435602X019

Description

• Model List:
  • FL100 Directional Felling Head

• 1. Contents
• 1.1. SafetySafety and Operator Conveniences
• 1.1.1. Safety and Operator Convenience Features
• 1.2. SafetyGeneral Precautions
• 1.2.1. Recognize Safety Information
• 1.2.2. Follow Safety Instructions
• 1.2.3. Operate Only If Qualified
• 1.2.4. Wear Protective Equipment
• 1.2.5. Protect Against Noise
• 1.2.6. Avoid Unauthorized Attachment Modifications
• 1.2.7. Protect Against Flying Debris
• 1.2.8. Inspect Attachment
• 1.2.9. Stay Clear of Moving Parts
• 1.2.10. Avoid HighPressure Fluids
• 1.2.11. Avoid HighPressure Oils
• 1.2.12. Decommissioning Proper Recycling and Disposal of Fluids and Components
• 1.2.13. Add Cab Guarding for Special Uses
• 1.2.14. Keep Clear of Saw
• 1.3. SafetyOperating Precautions
• 1.3.1. Use Steps and Handholds Correctly
• 1.3.2. Start Only From Operators Seat
• 1.3.3. Prevent Unintended Machine Movement
• 1.3.4. Avoid Work Site Hazards
• 1.3.5. Keep Riders Off Attachment
• 1.3.6. Avoid Machine Tip Over
• 1.3.7. Add and Operate Attachments Safely
• 1.3.8. Use Special Care When Operating
• 1.3.9. Inspect and Maintain Demolition Guard
• 1.3.10. Saw Chain Hazard
• 1.4. SafetyMaintenance Precautions
• 1.4.1. Service Accumulator Systems Safely
• 1.4.2. Remove Paint Before Welding or Heating
• 1.4.3. Make Welding Repairs Safely
• 1.4.4. Drive Metal Pins Safely
• 1.4.5. Practice Safe Maintenance
• 1.4.6. Use Proper Lifting Equipment
• 1.4.7. Chain Shot Guard Inspection
• 1.5. SafetySigns and Other Instructions
• 1.5.1. Safety Signs and Other Instructions
• 1.6. OperationInstall and Remove Attachment
• 1.6.1. Felling Head Installation
• 1.7. OperationOperating Attachment
• 1.7.1. Operator Ability
• 1.7.2. Daily Operating Checklist
• 1.7.3. Felling Head Operation
• 1.7.4. Large Diameter Trees
• 1.7.5. Harvesting Technique
• 1.7.6. General Cutting
• 1.7.7. DoubleCut Technique
• 1.7.8. QuarterCut Technique
• 1.8. MaintenanceAttachment
• 1.8.1. Bar Oil
• 1.8.2. Multipurpose Extreme Pressure (EP) Grease
• 1.8.3. Prepare Felling Head for Maintenance
• 1.8.4. Tilt Lock Cap Screw Storage
• 1.8.5. Maintenance Schedule
• 1.8.6. Lubricate Pins
• 1.8.7. Lubricate Single and Double Grapple Arm Pivot Points
• 1.8.8. Lubricate Rotator Ring
• 1.8.9. Lubricate Saw Swing Arm Bearing
• 1.8.10. Unified Inch Bolt and Screw Torque Values
• 1.8.11. Metric Bolt and Screw Torque Values
• 1.9. MaintenanceMiscellaneous
• 1.9.1. Welding on Machine
• 1.9.2. Bleed Chain Tensioning System
• 1.9.3. Fill Bar Oil Reservoir
• 1.9.4. Replace Saw Chain
• 1.9.5. Replace Saw Bar
• 1.9.6. Replace Saw Chain Sprocket
• 1.10. MiscellaneousOperational Checkout
• 1.10.1. Operational Checkout
• 1.10.1.1. Carrier Ignition Off Checks
• 1.10.1.2. Carrier Ignition On, Engine On Checks
• 1.11. MiscellaneousTroubleshooting
• 1.11.1. Using Troubleshooting Chart
• 1.11.2. Troubleshooting Procedure
• 1.12. MiscellaneousStorage
• 1.12.1. Prepare Attachment for Storage
• 1.12.2. Remove Attachment From Storage
• 1.13. MiscellaneousAttachment Numbers
• 1.13.1. Record Product Identification Number (PIN)
• 1.13.2. Record Rotate Motor Serial Number
• 1.13.3. Record Head Control Unit Serial Number
• 1.13.4. Record Saw Motor Serial Number
• 1.14. MiscellaneousSpecifications
• 1.14.1. Felling Head Specifications
• 2. Page Number
• 2.1. Section 11
• 2.2. Section 12
• 2.3. Section 13
• 2.4. Section 14
• 2.5. Section 15
• 2.6. Section 21
• 2.7. Section 22
• 2.8. Section 31
• 2.9. Section 32
• 2.10. Section 41
• 2.11. Section 42
• 2.12. Section 43
• 2.13. Section 44
• 2.14. Section 45