John Deere H310 Loader Operator Manual OMPXX11528

Description

• Model List:
  • H310 Loader

• 1. Introduction
• 1.1. Foreword
• 2. General Information
• 2.1. Machine Overview
• 2.2. Product View
• 2.3. Trademarks
• 2.4. Abbreviations
• 2.5. Regions and Country Versions
• 2.6. Dealers Record
• 2.7. Predelivery
• 2.8. Delivery
• 2.9. AfterSale
• 2.10. To the Dealer
• 2.11. Record Tractor Information
• 2.12. Recognize Safety Information
• 2.13. Understand Signal Words
• 2.14. Follow Safety Instructions
• 2.15. Prepare for Emergencies
• 2.16. Wear Protective Clothing
• 2.17. Park Machine Safely
• 2.18. Protect People and Animals
• 2.19. Operating the Loader Tractor Safely
• 2.20. Use Seat Belt Properly
• 2.21. Use Foldable ROPS and Seat Belt Properly
• 2.22. Use Caution on Slopes, Uneven Terrain, and Rough Ground
• 2.23. Avoid Injury or Death from Falling Loads
• 2.24. Carry Materials Safely
• 2.25. Transporting Round Bales Safely
• 2.26. Operate Grapple (If Equipped)
• 2.26.1. Avoid Injury or Death from Falling Round Bales
• 2.26.2. How to Pick Up a Round Bale
• 2.26.3. How to Pick Up a Round Bale on a Slope
• 2.26.4. How to Transport a Round Bale
• 2.26.5. How to Remove Material from a Pile
• 2.27. Driving on Public Roads
• 2.28. Operating Loader with Attachments from Other Manufacturers
• 2.29. Operate Bucket/Attachment Safely
• 2.30. Operating NonSelfLevelling Loaders
• 2.31. Avoid Power Lines
• 2.32. Dig Safely
• 2.33. Detach Loader Safely
• 2.34. Use Safety Lights and Devices
• 2.35. Practice Safe Maintenance
• 2.36. Service Loader Safely
• 2.37. Service Machines Safely
• 2.38. Service Accumulator Systems Safely
• 2.39. Avoid Heating Near Pressurized Fluid Lines
• 2.40. Check Hoses for Damage
• 2.41. Avoid HighPressure Fluids
• 2.42. Remove Paint Before Welding or Heating
• 2.43. Decommissioning Proper Recycling and Disposal of Fluids and Components
• 3. Safety Signs
• 3.1. Pictorial Safety Signs
• 3.2. Replace Safety Signs
• 3.3. Avoid HighPressure Spray on Safety Decals
• 3.4. Service Locks
• 3.5. Multicoupler
• 3.6. Ballast Box
• 3.7. Accumulator
• 4. Application Charts
• 4.1. Approved Tractors
• 4.2. Approved Front Tires, Load Index, Maximum Turn Angle, and Tread Setting
• 5. Prepare Tractor
• 5.1. Prepare the Tractor
• 5.2. Rear Ballast
• 5.3. Minimum Rear Ballast Requirements and Tire Ratings
• 5.3.1. Ballast
• 5.3.2. Tire Rating
• 5.4. Remove Front Weights
• 5.5. Front Tread Setting
• 5.6. Rear Tread Settings
• 5.7. Attach Ballast Box to Tractor Hitch
• 5.7.1. Three Point Hitch
• 5.7.2. Quick Coupler Hitch
• 5.8. Adjust Mechanical Selective Control Valve Detent Selector and Flow Control
• 5.9. Adjust Tractor Flow Rate and Timed Detent
• 6. Controls
• 6.1. Operate Loader with MultiFunction Lever
• 6.1.1. Mechanical MultiFunction Lever (Early Version)
• 6.1.2. Mechanical MultiFunction Lever (Later Version)
• 6.1.3. , 5M Series, and 6D Series MultiFunction Lever
• 6.1.4. Electronic MultiFunction Lever
• 6.2. Mechanical MultiFunction Lever with FrontLoader Dampening6M and 6R Series Tractors
• 6.3. Operate Loader with MultiFunction Lever6R Series Tractors
• 6.3.1. Electronic MultiFunction Lever
• 6.4. Relieve Hydraulic Pressure
• 7. Attach and Detach Loader
• 7.1. Attach Loader
• 7.2. Detach Loader
• 8. Attach and Detach Bucket or Attachment
• 8.1. Attachments Available
• 8.2. Attach Bucket or Attachment
• 8.3. Detach Bucket or Attachment
• 9. Transport
• 9.1. Keep Riders Off Machine
• 9.2. Driving on Public Roads
• 9.3. Carry Loads
• 10. Operate Loader
• 10.1. Raise and Lower Loader
• 10.2. Remove Material from a Pile
• 10.3. Level Bucket
• 10.4. Level and Scrape Forward
• 10.5. Level in Reverse
• 10.6. Dump Bucket
• 10.7. Operate Grapple (If Equipped)
• 10.7.1. Avoid Injury or Death from Falling Round Bales
• 10.7.2. How to Pick Up a Round Bale
• 10.7.3. How to Pick Up a Round Bale on a Slope
• 10.7.4. How to Transport a Round Bale
• 10.7.5. How to Remove Material from a Pile
• 10.8. Use Service Locks
• 10.8.1. Install Service Locks
• 10.8.2. Remove and Store Service Locks
• 10.9. Park Tractor with Loader Attached
• 11. Lubrication and Maintenance
• 11.1. Lubricate and Maintain Loader Safely
• 11.2. Perform Lubrication and Maintenance
• 11.3. Observe Lubrication Symbols
• 11.4. Multipurpose Extreme Pressure (EP) Grease
• 11.5. Alternative and Synthetic Lubricants
• 11.6. First 3 and 10 Hours
• 11.6.1. First 3 Hours
• 11.6.2. First 10 Hours
• 11.7. Every 10 Hours
• 11.7.1. Mechanical SelfLeveling Loaders
• 11.7.2. Non SelfLeveling Loaders
• 11.7.3. Latch Pins
• 11.7.4. Grapple
• 11.8. Every 50 Hours
• 11.8.1. Tighten Mounting Frame Hardware
• 11.8.2. Tighten MFWD Axle Housing and Kingpin Mounting Hardware
• 11.9. Every 100 Hours or MonthlyCheck Hydraulic Hoses
• 11.10. Every Six YearsReplace Hydraulic Hoses
• 12. Troubleshoot
• 12.1. Hydraulic
• 12.2. Mast Pin
• 13. Service
• 13.1. Service Loader or Tractor Safely (Loader Attached)
• 13.2. Work in Clean Area
• 13.3. Avoid HighPressure Fluids
• 13.4. ORing Installation
• 13.5. Tighten Hydraulic Fittings and Hoses
• 13.6. Replace Hydraulic Hoses, Couplers, Tubing, and Connectors
• 13.7. PlugIn Type Hydraulic Fittings
• 13.8. Access Front of TractorHood Guards with Latch Pins
• 13.9. Access Front of TractorRigid Hood Guards
• 13.10. Identify Hose ConnectionsLoadertoMulticoupler
• 13.11. Identify Hose ConnectionsLoadertoMidMount Couplers
• 13.12. Identify Hose Connections
• 13.13. Identify Loader Oil Line Connections
• 13.14. Metric Bolt and Screw Torque Values
• 13.15. Unified Inch Bolt and Screw Torque Values
• 14. Storage
• 14.1. Prepare Loader for Storage
• 14.2. Store Loader and Attachments
• 15. Specifications
• 15.1. Specification Parameters
• 15.2. H310 NSL Loader Specifications on 5085M, 5090M, 5100M, 5115M, 5100ML, 5115ML, and 5125ML (FT4) MFWD Tractors
• 15.3. H310 MSL Loader Specifications on 5085M, 5095M, and 5105M (IT4 and T3) MFWD Tractors
• 15.4. H310 NSL Loader Specifications on 5085M, 5095M, and 5105M (IT4 and T3) MFWD Tractors
• 15.5. H310 MSL Loader Specifications on 6105R, 6115R, and 6125R MFWD Tractors
• 15.6. H310 NSL Loader Specifications on 6105R, 6115R, and 6125R MFWD Tractors
• 15.7. H310 MSL Loader Specifications on 6430 Premium MFWD Tractor
• 15.8. H310 NSL Loader Specifications on 6430 Premium MFWD Tractor
• 15.9. H310 MSL Loader Specifications on 6100D, 6115D, 6130D, and 6140D (T3) MFWD Tractors
• 15.10. H310 NSL Loader Specifications on 6100D, 6115D, 6130D, and 6140D (T3) MFWD Tractors
• 15.11. H310 MSL Loader Specifications on 6105D, 6115D, 6130D, and 6140D (IT4) MFWD Tractors
• 15.12. H310 NSL Loader Specifications on 6105D, 6115D, 6130D, and 6140D (IT4) MFWD Tractors
• 15.13. H310 MSL Loader Specifications on 6105M, 6115M, and 6125M MFWD Tractors
• 15.14. H310 NSL Loader Specifications on 6105M, 6115M, and 6125M MFWD Tractors
• 15.15. H310 NSL Loader Specifications on 5085M, 5090M, 5100M, and 5115M (FT4) 2WD Tractors
• 15.16. H310 NSL Loader Specifications on 6100D, 6115D, 6130D, and 6140D (T3) 2WD Tractors
• 15.17. H310 NSL Loader Specifications on 6030 2WD Tractor
• 15.18. H310 NSL Loader Specifications on 6105M, 6115M, and 6125M 2WD Tractors
• 15.19. H310 NSL Loader Specifications on 6105R, 6115R, and 6125R 2WD Tractors
• 15.20. Round Bale Handling Capacities
• 16. Serial Number
• 16.1. Record Product Identification Number
• 16.2. Keep Proof of Ownership
• 16.3. Keep Machines Secure
• 17. John Deere Service Keeps You On The Job
• 17.1. John Deere Parts
• 17.2. The Right Tools
• 17.3. WellTrained Technicians
• 17.4. Prompt Service