Description
-
Model List:
- IGrade
- 1. Introduction
- 1.1. Foreword
- 1.2. John Deere Technical Information Bookstore
- 1.3. Recognize Safety Information
- 1.4. Understand Signal Words
- 1.5. Follow Safety Instructions
- 1.6. Practice Safe Maintenance
- 1.7. Use Steps and Handholds Correctly
- 1.8. Handle Electronic Components and Brackets Safely
- 1.9. Use Electronic Display Properly
- 1.10. Operate Guidance Systems Safely
- 1.11. Use Seat Belt Properly
- 1.12. Operate Implement Automation Systems Safely
- 1.13. Avoid HighPressure Fluids
- 2. Regulatory and Compliance Information
- 2.1. EU Declaration of Conformity
- 3. Introduction
- 3.1. Theory of Operation
- 3.2. iGrade Requirements
- 3.2.1. Hardware
- 3.2.2. Display
- 3.2.3. Receiver
- 3.2.4. Software
- 3.3. Navigate to Application Controller Using Generation 4 Display
- 3.4. Activate iGrade
- 3.5. Replace Erasable Programmable ReadOnly Memory (EPROM)
- 3.6. Machine Compatibility
- 4. Softkey Legend
- 4.1. Application Controller 1100Setup Softkey
- 4.2. Application Controller 1100Main Softkey
- 4.3. GreenStarMapping Softkey
- 4.4. GreenStarGuidance Softkey
- 4.5. StarFire ReceiverStarFire Softkey
- 4.6. StarFire ReceiverRTK Softkey
- 4.7. StarFire ReceiverSatellite Softkey
- 4.8. StarFire ReceiverDiagnostics Softkey
- 5. System Components
- 5.1. StarFire Receiver
- 5.2. StarFire Global Navigation Satellite System (GNSS) Antenna (Recommended)
- 5.3. Choke Ring Antenna (Optional)
- 5.4. Display
- 5.5. Application Controller 1100
- 5.6. Counterbalance Valve
- 5.7. External Valve
- 6. System Setup
- 6.1. Machine and Implement Setup
- 6.2. Connect Implement
- 6.3. Verify Hydraulic Hose Routing
- 6.4. Adjust Selective Control Valve (SCV)
- 6.4.1. Generation 4 CommandCenter CommandCenter is a trademark of Deere Company
- 6.4.2. GreenStarGreenStar is a trademark of Deere Company 3 CommandCenter
- 6.4.3. TouchSetTouchSet is a trademark of Deere Company Display
- 6.5. Set Up Hydraulic ControlSelective Control Valve (SCV) Threshold
- 6.6. Set Up Hydraulic ControlExternal Valve
- 6.7. Adjust Counterbalance Valve
- 6.8. Adjust Offsets
- 6.9. Set Up Global Position System (GPS) Receiver
- 6.10. Calibrate Terrain Compensation Module (TCM)
- 6.11. Configure Control Type
- 7. Grade Control
- 7.1. Theory of Operation
- 7.2. Input Grade Value
- 7.3. Operate Grade Control
- 8. Plane Control
- 8.1. Theory of Operation
- 8.2. Slope Direction
- 8.3. Control Selection
- 8.4. Select Active Plane
- 8.5. Define Single Slope Plane
- 8.6. Define Dual Slope Plane
- 8.7. Plane Calculator Theory of Operation
- 8.8. Plane Calculator
- 8.9. Locate Calculated Control Point on Plane
- 8.10. Plane Calculator with Topography Maps
- 8.10.1. Set Up Survey Mode
- 8.11. Retrieve Elevation Maps
- 8.12. Operate Plane Control
- 8.12.1. Fill Scrapers One at a Time
- 8.12.2. Fill Dual Scrapers at the Same Time
- 8.12.3. Fill Area
- 9. iGrade for Nonearth Moving Scrapers and Buckets
- 9.1. iGrade for Nonearth Moving Scrapers and Buckets
- 10. Cross Slope Control
- 10.1. Cross Slope Control
- 10.2. Select Cross Slope Control
- 10.3. Cross Slope Setup and Operation
- 11. Distance Trip
- 11.1. Theory of Operation
- 11.2. Select Distance Trip
- 11.3. Distance Trip Setup
- 11.4. Initiate Trip Cycle
- 11.5. Adjust Trip Cycle
- 12. Topography Maps
- 12.1. Theory of Operation
- 13. Remote ControlSerial Port
- 13.1. Theory of Operation
- 13.2. Serial Port Setup
- 13.3. Control Selection
- 13.4. Operate Remote Control
- 14. Optimize iGrade
- 14.1. Optimize iGrade
- 14.2. Load Limit
- 14.3. Max Cut
- 14.4. Optimize SCV Threshold and Elevation Control Sensitivity
- 14.5. Surface Maps
- 14.6. Utilize GSDNet Maps with iGrade
- 14.7. Optimize Grade Quality
- 14.8. Optimize Distance Trip
- 14.9. Visualizing and Demonstrating Slope Prior to Moving Material
- 14.10. Determining Slope Values for Drainage and Irrigation
- 14.11. Determining Vertical Distance
- 14.12. Determining Horizontal Distance
- 14.13. Guidance Lines
- 14.14. Data Collection Drive Patterns
- 14.15. Optimize Terrain Compensation Module (TCM)
- 14.16. Base Station
- 14.16.1. Configure Base Station
- 14.16.2. hr Survey
- 14.17. Control Point
- 14.18. Plane Management
- 14.19. Layout Manager
- 15. Disabling and Disconnecting iGrade
- 15.1. Disable iGrade
- 15.2. Disconnect iGrade System
- 16. ThirdParty Installation
- 16.1. Message Definition
- 16.2. Remote Control Serial Port Hardware
- 16.3. Distance Trip Low Side Driver
- 16.4. Long Trip Time Applications
- 17. Troubleshooting
- 17.1. Satellite Information
- 17.2. iGrade Performance
- 17.3. Install Jumper Wire
- 17.4. Reset Application Controller 1100
- 17.5. TroubleshootingiGrade System
- 17.6. TroubleshootingMachine
- 17.7. External Valve
- 17.8. Troubleshooting I/O Voltages Page
- 17.9. Data Cleanup
- 17.10. Clean Up ISOBUS VT
- 18. Maintenance
- 18.1. iGrade System
- 18.2. Preseason Checklist
- 18.3. Daily Checklist
- 18.4. Postseason Checklist
- 19. John Deere Service Literature Available
- 19.1. Technical Information
- 20. John Deere Service Keeps You on The Job
- 20.1. John Deere Is At Your Service
