Description
-
Model List:
- MX10 Cultivator
- 1. Introduction
- 1.1. Foreword
- 1.2. Identification View
- 1.3. A Message to Our Customers
- 1.4. Preliminary Checks
- 1.5. Regions and Country Versions
- 1.6. Machine Overview
- 1.7. Understand Signal Words
- 1.8. Follow Safety Instructions
- 1.9. Prepare for Emergencies
- 1.10. Wear Protective Clothing
- 1.11. Practice Safe Maintenance
- 1.12. Park Machine Safely
- 1.13. Remove Paint Before Welding or Heating
- 1.14. Avoid Heating Near Pressurized Fluid Lines
- 1.15. Avoid HighPressure Fluids
- 1.16. Keep Riders Off Machine
- 1.17. Use Safety Lights and Devices
- 1.18. Use Seat Belt Properly
- 1.19. Tow Loads Safely
- 1.20. Observe Maximum Transport Speed
- 1.21. Decommissioning Proper Recycling and Disposal of Fluids and Components
- 2. Safety Signs
- 2.1. Read Safety Signs Carefully
- 3. Preparing the Tractor
- 3.1. Tractor Power Required
- 3.2. Tire Pressure
- 3.3. Tractor Drawbar
- 3.4. Rear Wheel Tread
- 3.5. Front Wheel Tread
- 3.6. Front Ballast
- 3.7. Rear Ballast
- 3.8. Adjusting Sway Chains
- 3.9. Float Position
- 3.10. Hitch Link Length
- 4. Preparing the Machine
- 4.1. General Information
- 4.2. Importance of Proper Adjustment
- 4.3. Adjustment
- 5. Operating the Machine
- 5.1. Raising and Lowering the Cultivator
- 5.2. Load and Depth Control Selector Lever
- 5.3. Leveling the Cultivator
- 6. Attaching and Detaching
- 6.1. ThreePoint Hitch
- 6.2. Load and Depth Control Lever
- 6.2.1. Check Center Link Adjustment
- 6.3. Detaching the Cultivator
- 7. Transporting
- 7.1. Use a Safety Chain
- 7.2. Use Safety Lights and Devices
- 7.3. Tow Loads Safely
- 7.4. Observe Maximum Transport Speed
- 7.5. Transport Mode
- 7.6. Using Safety Lights and Accessories
- 8. Attachments
- 8.1. Front and Rear Chisels (01988)
- 8.2. Front and Rear Chisels (01988)
- 8.3. Front and Rear Chisel Positions
- 8.4. Front and Rear Chisel Positions Cont.
- 9. Assembly
- 9.1. Assembly
- 9.2. Read Assembly Instructions and Follow Illustrations Carefully
- 9.3. Straight Front Chisel and Curved Rear Chisel
- 9.4. Double Point Blade
- 10. Lubrication and Maintenance
- 10.1. Alternative Lubricants
- 10.2. Lubricant Storage
- 10.3. Waste Oil
- 10.4. Lubrication Symbols
- 11. Service
- 11.1. Unified Inch Bolt and Screw Torque Values
- 11.2. Metric Bolt and Screw Torque Values
- 11.3. Rust Prevention
- 11.4. Beginning of Season
- 11.5. End of Season
- 11.6. End of Season
- 12. Storage
- 12.1. Store Attachments Safely
- 12.2. Keep Your Cultivator Available
- 13. Specifications
- 13.1. Specifications
- 13.2. Product Identification Number
- 13.2.1. Content of Individual Positions or Group of Position Character Products Serial Number
- 14. John Deere Service Keeps You On The Job
- 14.1. John Deere Is At Your Service
- 14.2. John Deere Parts
- 14.3. The Right Tools
- 14.4. WellTrained Technicians
- 14.5. Prompt Service
