John Deere Orthman Planter Components Operator Manual OMA90150

Description

• Model List:
  • Orthman Planter Components

• 1. Contents
• 1.0.1. Recognize Safety Information
• 1.0.2. Understand Signal Words
• 1.0.3. Follow Safety Instructions
• 1.0.4. Prevent Machine Runaway
• 1.0.5. Operate the Machine Safely
• 1.0.6. Keep Riders Off Machine
• 1.0.7. Avoid TipOvers
• 1.0.8. Prepare for Emergencies
• 1.0.9. Wear Protective Clothing
• 1.0.10. Handle Agricultural Chemicals Safely
• 1.0.11. Use Safety Lights and Devices
• 1.0.12. Transport Safely
• 1.0.13. Tow Loads Safely
• 1.0.14. Observe Maximum Transport Speed
• 1.0.15. Service Machine Safely
• 1.0.16. Practice Safe Maintenance
• 1.0.17. Remove Paint Before Welding or Heating
• 1.0.18. Avoid Heating Near Pressurized Fluid Lines
• 1.0.19. Avoid HighPressure Fluids
• 1.0.20. Store Attachments Safely
• 1.0.21. Dispose of Waste Properly
• 1.0.22. Replace Safety Signs
• 1.1. Safety Signs
• 1.1.1. Safety Signs
• 1.2. Prepare Tractor
• 1.2.1. Use Your Tractor Operators Manual
• 1.2.2. Rear Wheel Weighting
• 1.2.3. Tractor Requirements
• 1.2.4. Setting Tractor Wheel Spacing
• 1.2.5. Recommended Tractor Settings
• 1.2.6. Low Pressure Case Drain Connection
• 1.3. Prepare Machine
• 1.3.1. Initial Use of CCS System
• 1.3.2. Before Use
• 1.3.3. Planting Terraces
• 1.4. Attach Machine
• 1.4.1. Use Your Tractor Operators Manual
• 1.4.2. CCS Fan and VacuMeter Motor (Case) Drain Requirements
• 1.4.3. VacuMeter Hydraulic Motor and Variable Rate Drive Return Couple
• 1.4.4. Attaching Warning Light Harness
• 1.4.5. Connect SeedStar Monitor Harness
• 1.4.6. Check Hydraulic System
• 1.4.7. Hydraulic Connections Recommendations
• 1.4.8. Independent Hitch and Lift Assist Wheel Control8000 Series Row
• 1.4.9. Single Lever Hydraulic Lift Control8000 Series RowCrop Tractor
• 1.4.10. Single Lever Control of Hitch And Double Acting Lift Assist Whee
• 1.4.11. Adjust Frame Height and Level Machine
• 1.5. Operate Machine
• 1.5.1. Roadway Transport Safety
• 1.5.2. General
• 1.5.3. Fold Tractor Warning Lights
• 1.5.4. VacuMeter Hydraulic System Operation
• 1.5.5. Adjust Planting Depth
• 1.5.6. Adjusting Closing Wheel Down Force
• 1.5.7. Center Closing Wheels
• 1.5.8. Adjust Closing Wheel Spacing
• 1.5.9. Stagger Closing Wheels
• 1.5.10. ThirdWidth Planting Drive DisconnectMachines Equipped with SEE
• 1.5.11. Raising and Lowering Machine
• 1.5.12. Shear Protection Points
• 1.5.13. Remove ProSeries XP Seed Meter Assembly From Row Unit
• 1.5.14. Install ProSeries XP Seed Meter Assembly on Row Unit
• 1.5.15. Pneumatic Down Force
• 1.6. Central Commodity System
• 1.6.1. CCS Operation
• 1.6.2. Tank Level Sensors
• 1.6.3. Operating CCS Tank Fill Lights
• 1.6.4. Operating Tank Lids
• 1.6.5. Filling CCS Tanks
• 1.6.6. Zeroing CCS Fan Pressure Gauge
• 1.6.7. Setting CCS Tank Pressure
• 1.6.8. Operating CCS System with Heavily Treated Seed or Very Large See
• 1.6.9. Bridged and Blocked CCS System
• 1.6.10. Operating CCS System When Planting Sorghum, Small Popcorn and Co
• 1.6.11. Planting Seed Plots with CCS Systems
• 1.6.12. Partially Cleaning Out CCS Tanks
• 1.6.13. Cleaning Out CCS Tanks
• 1.6.14. Cleaning Out Delivery Hoses and Vacuum Metering Units
• 1.6.15. Oil Reservoir for CCS Fan Motor
• 1.7. General Attachments
• 1.7.1. General
• 1.7.2. SeedStar Variable Rate Drive System
• 1.7.3. Walking Gauge Wheels
• 1.7.4. Seed Tubes
• 1.7.5. Rigid Scraper
• 1.7.6. HeavyDuty Scraper
• 1.7.7. Row Leveler Chain
• 1.7.8. Unit Mounted Row Cleaners
• 1.7.9. Conservation Furrowers
• 1.7.10. Disk Closing Attachment
• 1.7.11. VWings
• 1.7.12. Auxiliary Hydraulic Attachment Operation
• 1.8. Use of Talc Lubricant
• 1.8.1. Use of Talc Lubricant
• 1.9. Lubrication
• 1.9.1. Lubricate and Maintain Machine Safely
• 1.9.2. Perform Lubrication and Maintenance Procedures
• 1.9.3. Lubrication Symbols
• 1.9.4. Alternative Lubricants
• 1.9.5. Lubrication Intervals
• 1.10. Service and Adjustments
• 1.10.1. Service Intervals
• 1.10.2. Detailed Service InformationUse TM1721
• 1.10.3. Using Safe Service Procedures
• 1.10.4. Practice Safe Maintenance
• 1.10.5. Metric Bolt and Screw Torque Values
• 1.10.6. Unified Inch Bolt and Screw Torque Values
• 1.10.7. Welding Near Electronic Control Units
• 1.10.8. Keep Electronic Control Unit Connectors Clean
• 1.10.9. Service Tires Safely
• 1.10.10. Tightening Wheel Bolts
• 1.10.11. Checking Tire Inflation
• 1.10.12. Support Machine Before Service
• 1.10.13. Aligning Countershaft Wing Coupler
• 1.10.14. Install and Remove Standard Flush Face Seed Tubes
• 1.10.15. Clean Seed Tube Sensor
• 1.10.16. Setting CCS Row Unit Fan Switch
• 1.10.17. Install New Vacuum Seal
• 1.10.18. Inspect and Adjust Seed Opener Blades
• 1.10.19. Replace Seed Opener Blades and Seed Tube Guard
• 1.10.20. Adjust Gauge Wheels
• 1.10.21. Replace Shear Protection
• 1.10.22. Service Wheel Bearings
• 1.10.23. Tightening ProSeriesXP Meter Latch
• 1.10.24. ProSeriesXP Vacuum Meter Inspection and Service
• 1.10.25. Coulter Maintenance
• 1.10.26. Disk Closing Attachment
• 1.10.27. Inspect Vacuum Motor
• 1.10.28. Clean or Replace Compressor Air Filter
• 1.10.29. Clean Vacuum Manifold System
• 1.10.30. Drain CCS Fan Motor Oil Reservoir
• 1.11. Troubleshoot
• 1.11.1. CCS Fan Assembly
• 1.11.2. CCS Product Delivery
• 1.11.3. Row Units
• 1.11.4. Vacuum Meter
• 1.11.5. Row Command System
• 1.12. Storage
• 1.12.1. Removing From Storage
• 1.12.2. Storing Machine
• 1.12.3. Pneumatic Down Force Storage Procedures
• 1.13. Specifications
• 1.13.1. Specifications
• 1.13.2. Record Serial Number
• 1.13.3. The EC Declaration of Conformity applies only to machines which
• 1.13.4. Keep Proof of Ownership
• 1.13.5. Keep Machines Secure
• 1.14. John Deere Service Literature
• 1.14.1. Technical Information
• 1.15. John Deere Service Keeps You on the Job
• 1.15.1. John Deere Is At Your Service
• 2. Page Number
• 2.1. Section 05
• 2.2. Section 10
• 2.3. Section 15
• 2.4. Section 20
• 2.5. Section 25
• 2.6. Section 30
• 2.7. Section 35
• 2.8. Section 40
• 2.9. Section 45
• 2.10. Section 50
• 2.11. Section 55
• 2.12. Section 60
• 2.13. Section 65
• 2.14. Section 70