John Deere SeedStar 3 HP Monitor For ExactEmerge Planters Operator Manual OMA106222

Description

• Model List:
  • SeedStar 3 HP Monitor For ExactEmerge Planters

• 1. Contents
• 1.1. Identification Views
• 1.1.1. SeedStar 3 Identification Views
• 1.1.2. System Components
• 1.1.3. Recognize Safety Information
• 1.1.4. Understand Signal Words
• 1.1.5. Follow Safety Instructions
• 1.1.6. Replace Safety Signs
• 1.1.7. Prevent Machine Runaway
• 1.1.8. Avoid HighPressure Fluids
• 1.1.9. Prevent Battery Explosions
• 1.1.10. Welding Near Electronic Control Units
• 1.1.11. Keep Electronic Control Unit Connectors Clean
• 1.1.12. Read Operators Manuals for ISOBUS Controllers
• 1.2. Safety Signs
• 1.2.1. Safety Signs
• 1.3. How to Use Monitor
• 1.3.1. Use with GreenStar Monitors
• 1.3.2. Monitor Controls
• 1.3.3. Monitor Power Up and Power Down
• 1.3.4. Standard Buttons
• 1.3.5. Input Entry Methods
• 1.3.6. Screen Layout Manager
• 1.3.7. Screen Navigation
• 1.4. Monitor Settings
• 1.4.1. Configure Brightness, Volume, and Color
• 1.4.2. Configure Language and Units of Measure
• 1.4.3. Configure Date and Time
• 1.4.4. Touchscreen Calibration
• 1.5. Performance Monitor
• 1.5.1. Check Implement Width in Performance Monitor
• 1.5.2. Radar Configuration
• 1.5.3. Radar Calibration
• 1.6. Quick Reference
• 1.6.1. Quick Reference Setup
• 1.7. SeedStar 3 Setup Initial System Configuration
• 1.7.1. SeedStar 3 System Overview
• 1.7.2. System Components
• 1.7.3. Configure Frame Configuration
• 1.7.4. Section Control Timing
• 1.7.5. Seed Sensors Setup
• 1.7.6. Vacuum Sensor Configuration
• 1.7.7. Zero Vacuum Sensor
• 1.7.8. Pneumatic Down ForceAir Pressure Sensor
• 1.7.9. Liquid Fertilizer Sensors
• 1.7.10. Calibrate Common Start and Stop Height
• 1.7.11. Calibrate Separate Start and Stop Height
• 1.7.12. Ground Speed Source
• 1.7.13. Setup Curve Compensation
• 1.7.14. Alarms And Limits Defaults
• 1.7.15. Configure Mapping Groups
• 1.8. SeedStar 3 Setup
• 1.8.1. SeedStar Monitoring System Overview
• 1.8.2. RowCommand Overview
• 1.8.3. Configure RowCommand
• 1.8.4. Recommended RowCommand Section Configurations
• 1.8.5. Ride Dynamics Sensor Configuration
• 1.8.6. Pneumatic Down ForceAir Pressure Sensor
• 1.8.7. Down Force Sensor Configuration
• 1.8.8. Alarms and Limits Setup Page
• 1.8.9. Quick Setup Settings
• 1.8.10. Adjust Motion Sensor Gap
• 1.8.11. Adjust Parallel Arm Height Switch
• 1.9. Setup Seed Rates
• 1.9.1. Single Rate ConfigurationMeter, Crop, Disk, and Rates
• 1.9.2. By Mapping Group Rate ConfigurationMeter, Crop, Disk, and Rates
• 1.9.3. Custom Rate ConfigurationMeter, Crop, Disk, and Rates
• 1.10. Operating Machine
• 1.10.1. SeedStar 3 Overview
• 1.10.2. Individual Row Down Force (IRDF) Flushing Procedure
• 1.10.3. Quick Start Overview
• 1.10.4. Manual Set Fast Start Overview
• 1.10.5. Fast Start On Planter Down Overview
• 1.10.6. Hydraulic Power Generation System
• 1.10.7. Tractor Power Generation System
• 1.10.8. Curve Compensation Operation
• 1.11. SeedStar Main Run Screens
• 1.11.1. SeedStar 3 Navigation Tabs And Buttons
• 1.11.2. Seed Population
• 1.11.3. Seed Singulation
• 1.11.4. Seed Spacing Coefficient of Variation
• 1.11.5. Down Force
• 1.11.6. Ride Dynamics
• 1.11.7. Ground Contact
• 1.11.8. RowCommand
• 1.11.9. Row Details
• 1.11.10. Half Screen Layout
• 1.12. Down Force Operation
• 1.12.1. Service Machine Safely
• 1.12.2. Individual Row Down Force (IRDF) Operation
• 1.12.3. Pneumatic Down Force Operation
• 1.12.4. Pneumatic Down Force
• 1.12.5. Pressurize Pneumatic Down Force System
• 1.12.6. Depressurize Single Rank Pneumatic Down Force System
• 1.12.7. Depressurize Two Rank Pneumatic Down Force System
• 1.12.8. Relieve Rear Rank Pneumatic Down Force When Locking Up Rear Rows
• 1.12.9. Check Hydraulic Air Compressor Oil
• 1.12.10. Fill or Change Hydraulic Air Compressor Oil
• 1.12.11. Drain Air Storage Tank
• 1.13. Row Cleaner Control
• 1.13.1. Row Cleaner Setup
• 1.13.2. Row Cleaner Operation
• 1.14. Pneumatic Closing Wheel Control
• 1.14.1. Pneumatic Closing Wheel Setup
• 1.15. Vacuum Automation Control
• 1.15.1. Vacuum Automation Control
• 1.16. Rotate And Runoff Procedures
• 1.16.1. Rotate Seed Meters Overview
• 1.16.2. Runoff Display at Rear of Planter
• 1.16.3. Meter Runoff
• 1.16.4. Row Runoff
• 1.16.5. Planter Runoff
• 1.16.6. BrushBelt Runoff Only
• 1.17. Counters
• 1.17.1. Area Counters, Seeds Per Hour, Seeds Per Area, and Area Until Empty
• 1.18. SeedStar Diagnostics
• 1.18.1. Systems Data
• 1.18.2. Controller Hardware, Software, and Part Number Identification
• 1.18.3. Display Hardware, Software, and Part Number Identification
• 1.18.4. Pneumatic Closing Wheel Hardware and Software Identification
• 1.18.5. Row Unit Controller Hardware and Software Diagnostic
• 1.18.6. Row Unit Controller Addressing
• 1.18.7. System Voltages
• 1.18.8. Vacuum Sensor
• 1.18.9. Seed Sensor Reading
• 1.18.10. Gauge Wheel Down Force Diagnostics
• 1.18.11. Pneumatic Down Force System
• 1.18.12. Machine Speeds Diagnostics
• 1.18.13. Liquid Fertilizer Sensor
• 1.18.14. Air Compressor System
• 1.18.15. Row Unit Speed
• 1.18.16. Hydraulic Pressure
• 1.18.17. Planter Yaw Diagnostics
• 1.18.18. Individual Row Down Force Diagnostics
• 1.18.19. Pressure Sensor (Pneumatic Closing Wheel System)
• 1.18.20. Valve Test (IRDF System Only)
• 1.18.21. Valve Flush Test (IRDF System Only)
• 1.18.22. Air Purge Test (IRDF System Only)
• 1.19. Service Advisor Remote
• 1.19.1. Service Advisor Remote Operation
• 1.20. Troubleshooting
• 1.20.1. SeedStar Troubleshooting
• 1.20.2. Troubleshoot GreenStar Display
• 1.20.3. Troubleshoot SeedStar
• 1.20.4. Troubleshoot Single SetPoint Pneumatic Down Force System
• 1.20.5. Troubleshoot Dual SetPoint and Active Pneumatic Down Force System
• 1.21. Storage
• 1.21.1. Beginning of the Season Service
• 1.21.2. Liquid Fertilizer Sensor (If Equipped)
• 1.21.3. Vacuum Sensor
• 1.21.4. Pneumatic Down Force Air Spring Storage Procedures
• 1.22. Specifications
• 1.22.1. Record Serial Numbers
• 2. Page Number
• 2.1. Section 05
• 2.2. Section 10
• 2.3. Section 15
• 2.4. Section 20
• 2.5. Section 25
• 2.6. Section 30
• 2.7. Section 35
• 2.8. Section 40
• 2.9. Section 45
• 2.10. Section 50
• 2.11. Section 55
• 2.12. Section 60
• 2.13. Section 65
• 2.14. Section 70
• 2.15. Section 75
• 2.16. Section 80
• 2.17. Section 85
• 2.18. Section 90
• 2.19. Section 95
• 2.20. Section 100
• 2.21. Section 105
• 2.22. Section 110
• 2.23. Section 115