Description
-
Model List:
- 200 ATJ Australia
- 1. OPERATING AND SAFETY INSTRUCTIONS
- 1.1. INSTRUCTIONS TO THE COMPANY MANAGER
- 1.1.1. THE SITE
- 1.1.2. THE OPERATOR
- 1.1.3. PLATFORM
- 1.1.3.1. A SUITABILITY OF THE PLATFORM FOR THE TASK
- 1.1.3.2. B ADAPTING THE PLATFORM TO USUAL ENVIRONMENTAL CONDITIONS
- 1.1.3.3. C MODIFYING THE PLATFORM
- 1.1.4. INSTRUCTIONS
- 1.1.5. MAINTENANCE
- 1.2. INSTRUCTIONS FOR THE OPERATOR
- 1.2.1. INTRODUCTION
- 1.2.2. GENERAL INSTRUCTIONS
- 1.2.2.1. A INSTRUCTION MANUAL
- 1.2.2.2. B AUTHORISATION FOR USE IN FRANCE
- 1.2.2.3. C MAINTENANCE
- 1.2.2.4. D MODIFYING THE PLATFORM
- 1.2.2.5. E DIESEL PLATFORM AXLES
- 1.2.2.6. F SAFETY DEVICES
- 1.2.3. OPERATING INSTRUCTIONS
- 1.2.3.1. A BEFORE STARTINGUP THE PLATFORM
- 1.2.3.2. B DRIVERS OPERATING INSTRUCTIONS
- 1.2.3.3. C ENVIRONMENT
- 1.2.3.4. C1 OPERATION NEAR AERIAL CONDUCTORS (OVERHEAD POWER LINES)
- 1.2.3.5. D VISIBILITY
- 1.2.3.6. E STARTINGUP THE ENGINEPOWERED PLATFORM
- 1.2.3.7. E STARTING UP THE ELECTRICPOWERED PLATFORM
- 1.2.3.8. F OPERATING THE PLATFORM
- 1.2.3.9. G STOPPING THE PLATFORM
- 1.2.4. INSTRUCTIONS FOR WELDING AND BLOW TORCH WORK ON AN EXTERNAL STRUCTURE
- 1.2.4.1. A WITH AN ELECTRICAL WELDING SET
- 1.2.4.2. B WITH A BLOW TORCH
- 1.3. PLATFORM MAINTENANCE INSTRUCTIONS
- 1.3.1. GENERAL INSTRUCTIONS
- 1.3.2. MAINTENANCE
- 1.3.3. LUBRICANT AND FUEL LEVELS
- 1.3.4. BATTERY ELECTROLYTE LEVEL (ELECTRIC PLATFORM)
- 1.3.5. HYDRAULICS
- 1.3.6. ELECTRICITY
- 1.3.7. TILT SENSOR
- 1.3.8. WELDING ON THE ACCESS PLATFORM
- 1.3.9. WASHING THE PLATFORM
- 1.4. IF THE PLATFORM IS NOT TO BE USED FOR A LONG TIME
- 1.4.1. INTRODUCTION
- 1.4.2. PREPARING THE PLATFORM
- 1.4.3. PROTECTING THE ENGINE (DIESEL PLATFORM)
- 1.4.4. BATTERY CHARGING (ELECTRIC PLATFORM)
- 1.4.5. PROTECTING THE PLATFORM
- 1.4.6. BRINGING THE PLATFORM BACK INTO SERVICE
- 1.5. DISPOSING OF THE PLATFORM
- 1.5.1. RECYCLING OF MATERIALS
- 1.5.1.1. METALS
- 1.5.1.2. PLASTICS
- 1.5.1.3. RUBBER
- 1.5.1.4. GLASS
- 1.5.2. ENVIRONMENTAL PROTECTION
- 1.5.2.1. WORN OR DAMAGED PARTS
- 1.5.2.2. USED OIL
- 1.5.2.3. USED BATTERIES
- 2. DESCRIPTION
- 2.1. STICKERS
- 2.2. IDENTIFICATION OF THE PLATFORM
- 2.3. CHARACTERISTICS
- 2.4. DIMENSIONS AND DIAGRAM
- 2.5. SAFETY COMPONENTS
- 2.6. CONTROL PANEL AND SAFETY DEVICES AT GROUND LEVEL
- 2.7. CONTROL PANEL AND SAFETY DEVICES IN THE BASKET
- 2.8. SCREEN DISPLAY DESCRIPTION OF PAGES UP TO MACHINE NO. 949266
- 2.9. SUBMENU DEFINITIONS UP TO MACHINE No. 949266
- 2.10. SCREEN DISPLAY DESCRIPTION OF PAGES FROM MACHINE NO. 949267
- 2.11. SUBMENU DEFINITIONS FROM MACHINE No. 949267
- 2.12. OPERATING THE PLATFORM
- 2.13. TRANSPORTING THE PLATFORM
- 2.14. RESCUE PROCEDURE
- 2.15. OPTIONS
- 3. MAINTENANCE
- 3.1. INTRODUCTION
- 3.2. ORIGINAL MANITOU SPARE PARTS AND EQUIPMENT
- 3.3. PLATFORM MAINTENANCE
- 3.4. DAILY AND MONTHLY MAINTENANCE
- 3.5. COMPULSORY SERVICE AFTER FIRST 500 HOURS OR 6 MONTHS
- 3.6. PERIODIC SERVICE
- 3.7. OCCASIONAL MAINTENANCE AND OPERATION
- 3.8. FILTERING ELEMENTS AND BELTS
- 3.9. LUBRICANTS AND FUEL
- 3.10. Ü 10H DAILY MAINTENANCE OR EVERY 10 HOURS OF SERVICE
- 3.11. Ü 50H MONTHLY MAINTENANCE OR EVERY 50HOURS OF SERVICE
- 3.12. Ü 250H PERIODIC MAINTENANCE EVERY 250 HOURS OF SERVICE OR 6 MONTHS
- 3.13. Ü 500H PERIODIC MAINTENANCE EVERY 500HOURS OF SERVICE OR 1 YEAR
- 3.14. Ü 1000H PERIODIC SERVICE EVERY 1,000 HOURS OF SERVICE OR 2 YEARS
- 3.15. Ü 2000H PERIODIC SERVICE EVERY 2,000 HOURS OF SERVICE OR 4 YEARS
- 3.16. Ü OCCASIONAL MAINTENANCE
- 3.17. Ü OCCASIONAL OPERATION
