Manitou Axle 111 ( Dual Brake New Version) Service Manual 647902EN

Description

• Model List:
  • Axle 111 ( Dual Brake New Version)

• 1.1. Page de garde / Front page
• 2. ASM0227E_Rev.06 111
• 2.1. Contents
• 2.2. Introduction
• 2.2.1. Version tracking
• 2.2.2. Manual applicability and supported models
• 2.3. Specifications
• 2.3.1. Definition of viewpoints
• 2.3.2. Data plate
• 2.3.3. Conversion tables
• 2.3.3.1. Units of pressure
• 2.3.3.2. Units of weight
• 2.3.3.3. Units of torque
• 2.3.4. Torque specifications
• 2.3.4.1. Coarse pitch
• 2.3.4.2. Fine pitch
• 2.3.4.3. Wheel nut tightening torques
• 2.4. Maintenance
• 2.4.1. Maintenance points
• 2.4.2. Oil draining mandatory procedure
• 2.4.2.1. Central housing
• 2.4.2.2. Planetary gear reduction
• 2.4.3. Endstop plier setting
• 2.4.3.1. Retaining snap ring for bores
• 2.4.3.2. Retaining snap ring for shafts
• 2.4.4. Input seal greasing
• 2.4.4.1. Handling instruction greasing 1
• 2.4.4.2. Handling instruction greasing 2
• 2.4.5. Maintenance intervals
• 2.4.6. Lubricant sealant specifications
• 2.5. Safety precautions
• 2.6. Planetary reduction (flanged nuts version)
• 2.7. Manual emergency release
• 2.7.1. Exploded view
• 2.7.2. Manual emergency release
• 2.8. Adjustment after manual release
• 2.8.1. Exploded view
• 2.8.2. Adjustment after manual release
• 2.9. Brake wear check procedure
• 2.9.1. Exploded view
• 2.9.2. Brake wear check procedure
• 2.9.3. Special tools
• 2.10. Service and negative brake
• 2.11. Service and sahr incoming disc brake
• 2.11.1. Exploded view
• 2.11.2. Disassembly
• 2.11.3. Assembly
• 2.11.4. Checking wear and replacing the braking pads
• 2.11.5. Caliper assembly and setting
• 2.12. Incoming drum brake
• 2.13. Normal differential
• 2.13.1. Exploded view
• 2.13.2. Disassembly
• 2.13.3. Assembly
• 2.14. Limited slip differential unit 45
• 2.14.1. Exploded view
• 2.14.2. Disassembly
• 2.14.3. Assembly
• 2.15. Bevel pinion normal flange and nut revolution counter version
• 2.15.1. Exploded view
• 2.15.2. Disassembly
• 2.15.3. Assembly
• 2.15.4. Normal flange version
• 2.15.5. Revolution counter version
• 2.16. Ring and pinion adjusting version pinion integral and double arm
• 2.16.1. Exploded view
• 2.16.2. Install and adjust
• 2.17. Flanged reduction gear 603 type integral 603 input gear
• 2.18. Bevel pinion flanged to reduction gear 603
• 2.19. Separate pinion cover for flanged gearbox
• 2.19.1. Exploded view
• 2.19.2. Disassembly
• 2.19.3. Assembly
• 2.19.3.1. Calculating pinion bearings rolling torque
• 2.19.3.2. Calculating pinion center distance
• 2.20. United pinion cover for flanged gearbox
• 2.20.1. Exploded view
• 2.20.2. Disassembly
• 2.20.3. Assembly
• 2.20.3.1. Calculating pinion center distance
• 2.20.3.2. Calculating pinion bearings rolling torque
• 2.20.4. Special tools
• 2.21. Flanged reduction gear 315 type integral input gear (din flange)
• 2.21.1. Exploded view
• 2.21.2. Disassembly
• 2.21.3. Assembly
• 2.22. Flanged reduction gear 315 type interchangable input gear (end yoke flange)
• 2.23. Differential with block to spheres 100 (last version)
• 2.23.1. Exploded view
• 2.23.2. Disassembly
• 2.23.3. Assembly
• 2.24. Counter revolution sensor (dropin type)
• 2.24.1. Exploded view
• 2.24.2. Disassembly
• 2.24.3. Assembly