Description
-
Model List:
- H1 060 Hydrostatic Motor
- H1 080 Hydrostatic Motor
- H1 110 Hydrostatic Motor
- H1 160 Hydrostatic Motor
- H1 250 Hydrostatic Motor
- 1. Contents
- 2. Introduction
- 2.1. About this manual
- 2.2. General Instructions
- 2.3. Safety precautions
- 2.4. Symbols used in Danfoss literature
- 3. Disassembly
- 3.1. Proportional controls disassembly
- 3.2. Twoposition controls disassembly
- 3.3. Disassembly of controls with PCOR
- 3.4. Electric proportional controls M1CA/M2CA and L1BA/L2BA
- 3.5. Electric proportional controls D1MA/D2MA and K1KA/K2KA
- 3.6. Twoposition controls TD and PD
- 3.7. Twoposition controls TG and PG
- 3.8. Twoposition control EAA
- 3.9. Twoposition controls HEHE and HFHF
- 3.10. Twoposition control THHA
- 3.11. Twoposition control THHB
- 3.12. Twoposition control DHMA
- 3.13. Twoposition control DHMH
- 3.14. Twoposition control KHKA
- 3.15. Twoposition control KHKH
- 3.16. Twoposition controls MHCA and LHBA
- 3.17. Minimum displacement limiter
- 3.18. Maximum displacement limitertwoposition control
- 3.19. Speed Sensor
- 3.20. Servo piston coverproportional controls
- 3.21. Loop flushing spool and charge relief valve
- 3.22. Endcap and servo pistonproportional control
- 3.23. End cap and servo pistontwoposition controls
- 3.24. Cylinder block and sync Shaft assembly
- 3.25. Shaft assembly
- 4. Inspection
- 4.1. Overview
- 4.2. Shaft assembly
- 4.3. Pistons and piston rings inspection
- 4.4. Synchronizing shaft
- 4.5. Control shuttle valve
- 4.6. Optional Minimum displacement limiter
- 4.7. Shaft in housing
- 4.8. Synchronizing shaft
- 4.9. Pistons and cylinder block
- 4.10. Bearing plate
- 4.11. Servo piston and valve segmentproportional control
- 4.12. Servo piston and valve segmenttwo position control
- 4.13. Endcap assembly
- 4.14. Loop flushing charge relief valve and spool
- 4.15. Shaft seal
- 4.16. Servo coverproportional control
- 4.17. Speed sensor
- 4.18. Minimum displacement limiter
- 4.19. Maximum displacement limitertwoposition control
- 4.20. Electric proportional controls M1CA/M2CA and L1BA/L2BA
- 4.21. Electric proportional controls D1M1/D2M2 and K1K1/K2K2
- 4.22. Twoposition controls TD and PD
- 4.23. Twoposition controls TG and PG
- 4.24. Twoposition control EAA
- 4.25. Twoposition controls HEHE and HFHF
- 4.26. Twoposition control THHA
- 4.27. Twoposition control THHB
- 4.28. Twoposition control DHMA
- 4.29. Twoposition control DHMH
- 4.30. Twoposition control KHKA
- 4.31. Twoposition control KHKH
- 4.32. Twoposition controls MHCA and LHBA
- 4.33. Proportional controls installation
- 4.34. Twoposition controls installation
- 4.35. Controls with PCOR installation
- 5. Startup Procedures
- 5.1. Overview
- 5.2. Initial startup procedures
- 5.3. Adjustments
- 5.4. Pressure measurements
- 6. Port locations
- 6.1. Ports and Gauge Information
- 7. Torque chart
- 7.1. Fasteners and plugs
- 7.2. Fastener size and torque chart
- 7.3. Plug size and torque chart
- 8. Page vierge
