Description
-
Model List:
- MRT 1440 EASY 75P 400 ST3B S2
- MRT 1440 EASY 55P 400 ST4 S2
- MRT-X 1440 EASY 75P 400 ST3A S2
- MRT 1640 EASY 75P 400 ST3B S2
- MRT 1640 EASY 55P 400 ST4 S2
- MRT-X 1640 EASY 75P 400 ST3A S2
- MRT 1640 EASY 75P 360 ST3B S2
- MRT 1640 EASY 55P 360 ST4 S2
- MRT-X 1640 EASY 75P 360 ST3A S2
- MRT 1840 EASY 75P 400 ST3B S2
- MRT 1840 EASY 55P 400 ST4 S2
- MRT-X 1840 EASY 75P 400 ST3A S2
- MRT 1840 EASY 75P 360 ST3B S2
- MRT 1840 EASY 55P 360 ST4 S2
- MRT-X 1840 EASY 75P 360 ST3A S2
- 1. GROUP_00_MR647638EN
- 1.1. Page de garde / Front page
- 1.2. Sommaire général General table of content
- 1.4. GENERAL INSTRUCTIONS AND SAFETY NOTICE
- 1.4.1. INTRODUCTION
- 1.4.2. GENERAL CHARACTERISTICS AND SPECITICATION
- 1.4.3. GENERAL LOCATION
- 1.4.4. GENERAL CONTROL AND ADJUSTMENT
- 2. GROUP_10_MR647638EN
- 2.2. ENGINE CHARACTERISTICS AND SPECIFICATIONS
- 2.2.1. MRT 1440/1640/1840 ENGINE CHARACTERISTICS
- 2.2.2. POSITION OF THE ENGINE COMPONENTS
- 2.2.3. CHECKING AND ADJUSTING THE ENGINE
- 2.2.4. REMOVING THE ENGINE
- 3. GROUP_20_MR647638EN
- 3.2. FEATURES AND TECHNICAL SPECIFICATIONS OF THE TRANSMISSION
- 3.2.1. REXROTH HYDROSTATIC TRANSMISSION
- 3.2.2. TRANSMISSION LAYOUTS
- 3.2.3. POSITION OF THE TRANSMISSION COMPONENTS
- 3.2.4. CHECKING AND ADJUSTING THE TRANSMISSION
- 3.2.5. REMOVING THE HYDROSTATIC TRANSMISSION
- 3.2.6. REINSERTING THE HYDROSTATIC TRANSMISSION
- 3.2.7. SPECIAL TOOLS FOR THE TRANSMISSION
- 4. GROUP_30_MR647638EN
- 4.2. REMOVING THE AXLE
- 4.2.1. GENERAL INFORMATION
- 4.2.2. REINSERTING THE FRONT AND REAR AXLES
- 5. GROUP_40_MR647638EN
- 5.2. FEATURES AND TECHNICAL SPECIFICATIONS OF THE BRAKES
- 5.2.1. SERVICE BRAKE
- 5.2.2. POSITION OF THE BRAKES COMPONENTS
- 5.2.3. CHECKING AND ADJUSTING THE BRAKES
- 5.2.4. SPECIAL TOOLS FOR THE BRAKES
- 6. GROUP_50_MR647638EN
- 6.2. BOOM CHARACTERISTICS AND SPECIFICATIONS
- 6.2.1. BOOM WITH TWO EXTENSIONS
- 6.2.2. BOOM COMPONENTS LOCATION
- 6.2.3. BOOM CONTROL AND ADJUSTMENT
- 6.2.4. boom removal
- 6.2.5. boom refit
- 7. GROUP_70_MR647638EN
- 7.2. HYDRAULIC SCHEMATIC DIAGRAMS
- 7.2.1. MRT 1440 1640 ST3B (400)
- 7.2.2. HYDRAULIC COMPONENTS LOCATION
- 7.2.3. HYDRAULIC COMPONENTS LOCATION
- 7.2.4. HYDRAULIC COMPONENTS REMOVAL
- 7.2.5. REFITTING THE HYDRAULIC COMPONENTS
- 7.2.6. HYDRAULIC SPECIFIC TOOLING
- 8. GROUP_80_MR647638EN
- 8.1. ELECTRICAL FEATURES AND SPECIFICATIONS
- 8.1.1. SOFTWARE
- 8.1.2. WIRING DIAGRAMS
- 8.1.3. POSITION OF THE ELECTRICAL COMPONENTS
- 8.1.4. ELECTRICAL CONTROL AND ADJUSTMENT
- 8.1.5. spECIAL TOOLS FOR THE ELECTRICAL SYSTEM
- 9. GROUP_85_MR647638EN
- 9.2. DRIVERS CAB REMOVAL
- 9.2.1. GENERAL INFORMATION
- 9.2.2. DRIVERS CAB REFIT
- 10. GROUP_90_MR647638EN
- 10.2. REMOVING THE TURRET
- 10.2.1. GENERAL INFORMATION
- 10.2.2. REFITTING THE TURRET
