Description
-
Model List:
- MT-X 733 S1 MINING
- 1. Page de garde / Front page
- 2. Sommaire général General table of content
- 4. GENERAL, CHARACTERISTICS AND SAFETY
- 4.1. Work during the Warranty Period
- 4.2. GENERAL INSTRUCTIONS AND SAFETY NOTICE
- 4.2.1. FOREWORD
- 4.2.2. SERVICING POSITION
- 4.2.3. EXPLANATION OF SYMBOLS
- 4.2.4. SERVICING RULES
- 4.3. GENERAL CHARACTERISTICS AND SPECIFICATIONS
- 4.3.1. CHARACTERISTICS
- 4.3.2. LUBRICANTS AND FUEL
- 4.3.3. Dimensions
- 4.4. General location
- 4.4.1. Location of the name and identification plate
- 4.5. GENERAL CONTROL AND ADJUSTMENT
- 4.5.1. STANDARD TIGHTENING TORQUES
- 4.5.2. METRIC IMPERIAL UNIT CONVERSION
- 6. HYDRAULICS
- 6.1. Hydraulic characteristics and specifications
- 6.1.1. Hydraulic component sheets
- 6.1.1.1. SDM 140 DISTRIBUTOR
- 6.2. Hydraulic schematic diagrams
- 6.2.1. MTX 733 S1 MINING
- 6.2.1.2. Diagram
- 6.2.2. Hydraulic components location
- 6.2.3. MTX 733 S1 MINING
- 6.3. Hydraulic controls and adjustments
- 6.3.1. Distributor control logic
- 6.3.2. Aggravating movements cutoff operating principle
- 6.3.3. CASAPPA KP30 22 pump tightening torques
- 6.4. Specific tooling
- 6.4.1. Basic and digital manometer box
- 6.4.2. INFLATION KIT BOX
- 8. EWiring diagrams
- 8.1. Examples of coding on the wiring diagrams
- 8.1.1. Cable marking on an electrical wiring harness
- 8.1.2. MTX 733 S1 MINING
- 8.1.2.1. Position of connectors by diagram
- 8.1.2.2. Key Diagram 1 Starting
- 8.1.2.3. Diagram 1 Starting
- 8.1.2.4. Key Diagram 2 CAN
- 8.1.2.5. Diagram 2 CAN
- 8.1.2.6. Key Diagram 3 Transmission
- 8.1.2.7. Diagram 3 Transmission
- 8.1.2.8. Key Diagram 4 Hydraulic movements
- 8.1.2.9. Diagram 4 Hydraulic movements
- 8.1.2.10. Key Diagram 5 Sensors
- 8.1.2.11. Diagram 5 Sensors
- 8.1.2.12. Key Diagram 6 Ventilation, wipers and air conditioning
- 8.1.2.13. Diagram 6 Ventilation, wipers and air conditioning
- 8.1.2.14. Key Diagram 7 Options
- 8.1.2.15. Diagram 7 Options
- 8.1.2.16. Key Diagram 8 Lights and signals 1
- 8.1.2.17. Diagram 8 Lights and signals 1
- 8.1.2.18. Key Diagram 9 Lights and signals 2
- 8.1.2.19. Diagram 9 Lights and signals 2
- 8.1.2.20. Key Diagram 10 Relays mining KIT
- 8.1.2.21. Diagram 10 Relays mining KIT
- 8.1.2.22. Key Diagram 11 mining kit unit
- 8.1.2.23. Diagram 11 mining kit unit
- 8.1.2.24. Key Diagram 12 Emergency pushbutton
- 8.1.2.25. Diagram 12 emergency pushbutton
- 8.1.2.26. key Diagram 13 guardian angel
- 8.1.2.27. Diagram 13 guardian angel
- 8.2. Electricity locations
- 8.2.2. Main harness MTX 733 2D
- 8.2.3. Main harness MTX 733 3D
- 8.2.4. Engine 2D harness
- 8.2.5. Engine 3D harness
- 8.2.6. Distributor 2D harness
- 8.2.7. Distributor 3D harness
- 8.3. CONTROL AND ADJUSTMENT
- 8.3.1. BOOM ANGLE ANGULAR SENSOR ADJUSTMENT
- 8.3.2. LONGITUDINAL STABILITY INDICATOR (LLMI)
- 8.3.2.1. ERROR CODES
- 8.3.2.2. TESTING THE LONGITUDINAL STABILITY LIMITER AND WARNING DEVICE
- 8.3.2.3. STRAIN GAUGE AND ANGLE SENSOR CALIBRATION (DEALER PROCEDURE)
- 8.3.2.4. STRAIN GAUGE RECALIBRATION (CLIENT PROCEDURE)
- 8.3.2.5. AGGRAVATING HYDRAULIC MOVEMENTS CUTOFF
- 8.3.2.6. LED ILLUMINATION ACCORDING TO CHANGES IN GAUGE SIGNAL
- 8.4. Electricity removal refit
- 8.4.1. Replace the strain gauge
- 8.4.1.1. LOCATION
- 8.4.1.2. AXLE PREPARATION
- 8.4.1.3. CHARACTERISTICS OF PRODUCTS USED
- 8.4.1.4. CHARACTERISTICS OF FASTENING SCREWS
- 8.4.1.5. ASSEMBLY PRECAUTIONS AND TIGHTENING TORQUE
- 8.4.1.6. STRAIN GAUGE
- 8.5. Troubleshooting
- 8.5.1. ERROR CODES
- 8.5.1.1. Main ECU
- 8.6. SPECIFIC TOOLING
- 8.6.1. BREAKOUT BOXES
- 8.6.2. Electrovalve adapter
- 8.6.3. DIAGNOSTIC TOOLS
- 8.6.3.1. DIAGNOSTICS CASE
- 8.6.3.2. CONNECTIONS TO LIFT TRUCK
- 8.6.3.3. ENGINE ADAPTATION KIT
