Description
-
Model List:
- Type 211 Axle
- 1. CONTENTS
- 2. INTRODUCTION
- 2.1. VERSION TRACKING
- 2.2. MANUAL APPLICABILITY AND SUPPORTED MODELS
- 3. SPECIFICATIONS
- 3.1. DEFINITION OF VIEWPOINTS
- 3.2. DATA PLATE
- 3.3. CONVERSION TABLES
- 3.4. TORQUE SPECIFICATIONS
- 3.4.1. COARSE PITCH
- 3.4.2. FINE PITCH
- 3.4.3. WHEEL NUT TIGHTENING TORQUES
- 3.5. MAINTENANCE
- 3.5.1. MAINTENANCE POINTS
- 4. MANDATORY PROCEDURE
- 4.1. OIL DRAINING
- 4.1.1. CENTRAL HOUSING
- 4.1.2. PLANETARY GEAR REDUCTION
- 4.2. ENDSTOP PLIER SETTING
- 4.2.1. RETAINING SNAP RING FOR BORES
- 4.2.2. RETAINING SNAP RING FOR SHAFTS
- 4.3. INPUT SEAL GREASING
- 4.3.1. Handling instruction greasing 1
- 4.3.2. Handling instruction greasing 2
- 4.4. MAINTENANCE INTERVALS
- 4.5. LUBRICANT SEALANT SPECIFICATIONS
- 5. SAFETY PRECAUTIONS
- 6. PLANETARY REDUCTION 16 AND THE STEERING CASE
- 7. STEERING CYLINDER
- 8. BRAKE SERVICE BRAKE, NEGATIVE BRAKE, 45 LOCKED AND 100 LOCKED
- 8.1. EXPLODED VIEW
- 8.2. BRAKE WORKING CONDITIONS
- 8.2.1. SAHR BRAKE A PPLIED
- 8.2.2. SAHR BRAKE RELEASED
- 8.2.3. SERVICE BRAKE APPLIED
- 8.2.4. DIFFERENTIAL LOCK APPLIED
- 8.3. EMERGENCY RELEASE INSTRUCTIONS
- 8.3.1. RESET OF FAILS SAFE BRAKE FUNCTION
- 8.4. DISASSEMBLY
- 8.5. ASSEMBLY
- 8.6. BRAKE PISTON GAP CHECK
- 8.7. SPECIAL TOOLS
- 9. BRAKE NEGATIVE BRAKE 4 CUP SPRINGS VERSION
- 9.1. EXPLODED VIEW
- 9.2. DISASSEMBLY
- 9.3. ASSEMBLY
- 10. NORMAL PRELOADED DIFFERENTIAL UNIT (OLD VERSION)
- 10.1. EXPLODED VIEW
- 10.2. DISASSEMBLY
- 10.3. ASSEMBLY
- 11. NORMAL PRELOADED DIFFERENTIAL UNIT (INTERMEDIATE VERSION)
- 11.1. EXPLODED VIEW
- 11.2. DISASSEMBLY
- 11.3. ASSEMBLY
- 12. NORMAL PRELOADED DIFFERENTIAL UNIT (LAST VERSION)
- 12.1. EXPLODED VIEW
- 12.2. DISASSEMBLY
- 12.3. ASSEMBLY
- 13. FLANGED REDUCTION GEAR 603 TYPE INTEGRAL 603 INPUT GEAR
- 14. BEVEL PINION NORMAL FLANGE AND NUT REVOLUTION COUNTER VERSION
- 14.1. EXPLODED VIEW
- 14.2. DISASSEMBLY
- 14.3. ASSEMBLY
- 14.3.1. NORMAL FLANGE VERSION
- 14.3.2. REVOLUTION COUNTER VERSION
- 15. RING AND PINION ADJUSTING STEP FOR PRELOADED DIFFERENTIAL
- 15.1. EXPLODED VIEW
- 15.2. INSTALL AND ADJUST
- 16. SWINGING SUPPORT
- 16.1. EXPLODED VIEW
- 16.2. DISASSEMBLY
- 16.3. ASSEMBLY
- 17. PLANETARY REDUCTION 14,23
- 17.1. EXPLODED VIEW
- 17.2. DISASSEMBLY
- 17.3. ASSEMBLY
- 18. BRAKE INCOMING DISC BRAKE
- 18.1. EXPLODED VIEW
- 18.2. DISASSEMBLY
- 18.3. ASSEMBLY
- 18.4. CHECKING WEAR AND REPLACING THE BRAKING PADS
- 19. SERVICE AND MECHANICAL PARKING BRAKE
- 19.1. EXPLODED VIEW
- 19.2. DISASSEMBLY
- 19.3. ASSEMBLY
- 20. PARKING BRAKE AND DIFFERENTIAL HYDRAULIC LOCK 100
- 20.1. EXPLODED VIEW
- 20.2. DISASSEMBLY
- 20.3. ASSEMBLY
- 21. DIFFERENTIAL WITH BLOCK TO SPHERES 100 (OLD VERSION)
- 21.1. EXPLODED VIEW
- 21.2. DISASSEMBLY
- 21.3. ASSEMBLY
- 22. DIFFERENTIAL WITH BLOCK TO SPHERES 100 (LAST VERSION)
- 22.1. EXPLODED VIEW
- 22.2. DISASSEMBLY
- 22.3. ASSEMBLY
- 23. NORMAL DIFFERENTIAL (OLD VERSION)
- 23.1. EXPLODED VIEW
- 23.2. DISASSEMBLY
- 23.3. ASSEMBLY
- 24. NORMAL DIFFERENTIAL (LAST VERSION)
- 24.1. EXPLODED VIEW
- 24.2. DISASSEMBLY
- 24.3. ASSEMBLY
- 25. LIMITED SLIP DIFFERENTIAL UNIT 45 (OLD VERSION)
- 25.1. EXPLODED VIEW
- 25.2. DISASSEMBLY
- 25.3. ASSEMBLY
- 26. LIMITED SLIP DIFFERENTIAL UNIT 45 (LAST VERSION)
- 26.1. EXPLODED VIEW
- 26.2. DISASSEMBLY
- 26.3. ASSEMBLY
- 27. PRELOADED LIMITED SLIP DIFFERENTIAL UNIT 45 UNIT (OLD VERSION)
- 27.1. EXPLODED VIEW
- 27.2. DISASSEMBLY
- 27.3. ASSEMBLY
- 28. PRELOADED LIMITED SLIP DIFFERENTIAL UNIT 45 (INTERMEDIATE VERSION)
- 28.1. EXPLODED VIEW
- 28.2. DISASSEMBLY
- 28.3. ASSEMBLY
- 29. PRELOADED LIMITED SLIP DIFFERENTIAL UNIT 45 (LAST VERSION)
- 29.1. EXPLODED VIEW
- 29.2. DISASSEMBLY
- 29.3. ASSEMBLY
- 30. BEVEL PINION FLANGED TO REDUCTION GEAR 603
- 31. RING AND PINION ADJUSTING VERSION PINION COVER AND SINGLE ARM
- 31.1. EXPLODED VIEW
- 31.2. INSTALL AND ADJUST
- 32. RING AND PINION ADJUSTING VERSION PINION INTEGRAL AND DOUBLE ARM
- 32.1. EXPLODED VIEW
- 32.2. INSTALL AND ADJUST
- 33. SEPARATE PINION COVER FOR FLANGED GEARBOX
- 33.1. EXPLODED VIEW
- 33.2. DISASSEMBLY
- 33.3. ASSEMBLY
- 33.3.1. CALCULATING PINION BEARINGS ROLLING TORQUE
- 33.3.2. CALCULATING PINION CENTER DISTANCE
- 34. UNITED PINION COVER FOR FLANGED GEARBOX
- 34.1. EXPLODED VIEW
- 34.2. DISASSEMBLY
- 34.3. ASSEMBLY
- 34.3.1. CALCULATING PINION CENTER DISTANCE
- 34.3.2. CALCULATING PINION BEARINGS ROLLING TORQUE
- 34.4. SPECIAL TOOLS
- 35. STEERING KNUCKLE KING PIN PRELOADED BY BELLEVILLE WASHERS
- 36. SERVICE BRAKE, NEGATIVE BRAKE, 100 DIFFERENTIAL LOCK (NEW VERSION OPTIONAL)
- 36.1. EXPLODED VIEW
- 36.2. BRAKING DISCS WEAR CHECK
- 36.3. EMERGENCY RELEASE INSTRUCTIONS
- 36.3.1. RESET OF FAILS SAFE BRAKE FUNCTION
- 36.4. DISASSEMBLY
- 36.5. ASSEMBLY
- 36.6. BRAKE PISTON GAP CHECK
- 36.7. SPECIAL TOOLS
- 37. SERVICE BRAKE, 100 DIFFERENTIAL LOCK (NEW VERSION OPTIONAL)
- 37.1. EXPLODED VIEW
- 37.2. BRAKING DISCS WEAR CHECK
- 37.3. DISASSEMBLY
- 37.4. ASSEMBLY
- 37.5. BRAKE PISTON GAP CHECK
- 37.6. SPECIAL TOOLS
- 38. Page vierge
