John Deere 615 P Belt Pickup Operator Manual OMH232865
$30
- Type Of Manual: Operator Manual
- Manual ID: OMH232865
- Format: PDF
- Size: 3.5MB
- Number of Pages: 96
Description
-
Model List:
- 615 P Belt Pickup
- 1. Contents
- 1.1. Belt Pickup Safety Features
- 1.1.1. Belt Pickup Safety Features
- 1.1.2. Recognize Safety Information
- 1.1.3. Understand Signal Words
- 1.1.4. Follow Safety Instructions
- 1.1.5. Use Safety Lights and Devices
- 1.1.6. Prepare for Emergencies
- 1.1.7. Wear Protective Clothing
- 1.1.8. Store Attachments Safely
- 1.1.9. Road Transport Disconnect Switch (Black)
- 1.1.10. Transport Combine With Header Safely
- 1.1.11. Guards and Shields
- 1.1.12. Stay Clear of Rotating Drivelines
- 1.1.13. Ballasting for Safe Ground Contact
- 1.1.14. Parking and Leaving the Combine
- 1.1.15. Practice Safe Maintenance
- 1.1.16. Service Machines Safely
- 1.1.17. Support Machine Properly
- 1.1.18. Protect Against High Pressure Spray
- 1.1.19. Avoid Heating Near Pressurized Fluid Lines
- 1.1.20. Avoid Contact with Moving Parts
- 1.1.21. Service Belts Safely
- 1.1.22. Service Tires Safely
- 1.1.23. Avoid HighPressure Fluids
- 1.1.24. Remove Paint Before Welding or Heating
- 1.1.25. Dispose of Waste Properly
- 1.1.26. Replace Safety Signs
- 1.2. Safety Sign Location
- 1.2.1. Safety Sign Location
- 1.3. Attaching and Detaching
- 1.3.1. Rear Auger Stripper Extension Location
- 1.3.2. Attaching Belt Pickup To 60 and 70 Series Combines
- 1.3.3. Detaching Belt Pickup From 60 and 70 Series Combines
- 1.3.4. Adjusting MultiCoupler Latching Cable
- 1.3.5. Manual Latch/Unlatch Feeder House Pins (without latching cable)
- 1.3.6. Feeder House Latching Pins (Cleanout)
- 1.3.7. Feeder House Manual Unlatching (With Latching Cable)
- 1.3.8. Latching Cable Shear Screw Location
- 1.3.9. Attaching Header to Combines with Serial Number 715,000
- 1.4. Transporting
- 1.4.1. Road Transport Disconnect Switch (Black)
- 1.4.2. Transporting
- 1.5. Operation
- 1.5.1. Pickup Speed
- 1.5.2. Pickup Height
- 1.5.3. Pickup Pitch
- 1.5.4. Pickup Pitch (Normal Windrow Condition)
- 1.5.5. Pickup Pitch (Poor Windrow Condition)
- 1.5.6. Pickup Pitch (Rocky Conditions)
- 1.5.7. Windrow HoldDown (Wind Screen)
- 1.5.8. Special Conditions (Light Gauge Wheel Pressure)
- 1.5.9. Large and Uneven Windrows
- 1.6. Calibration and Programing Procedures
- 1.6.1. When to Calibrate
- 1.6.2. Before Calibration
- 1.6.3. Air Spring Set Up (Prior to Header Calibration)
- 1.6.4. Feeder Face Adjustment
- 1.6.5. User Calibration Procedures for 70 Series Combines
- 1.6.6. User Calibration Procedures for 50/60 Series Combines
- 1.6.7. Calibration Error Codes
- 1.6.8. Typical Belt Pickup Error Codes
- 1.6.9. Armrest Functions
- 1.6.10. Active Header Control Display
- 1.6.11. Description of Automatic Header Height Control System
- 1.7. Belt Pickup Adjustments
- 1.7.1. Service Tires Safely
- 1.7.2. Adjusting Air Springs
- 1.7.3. Air Spring Set Up (Prior to Header Calibration)
- 1.7.4. Periodic Checking of Air Spring Pressure
- 1.7.5. Adjusting Windrow HoldDown (Wind Screen)
- 1.7.6. Adjusting Auger Position
- 1.7.7. Adjusting Auger Height
- 1.7.8. Adjusting Auger Fore/Aft (Left Side)
- 1.7.9. Adjust Auger Fore/Aft (Right Side)
- 1.7.10. Adjusting Finger Timing
- 1.7.11. Adjusting Rear Stripper
- 1.7.12. Adjusting Floor Stripper
- 1.7.13. Adjusting Auger Chain Tension
- 1.7.14. Adjusting Transfer Belt Tension
- 1.7.15. Adjusting Picking Belt Tension
- 1.7.16. Belt Tracking Issues
- 1.7.17. Feeder House Rate/Sensitivity Adjust Switch (Black) 70 Series
- 1.7.18. Adjusting Header Drop Rate (If Equipped With Header Height Sensing)
- 1.7.19. DIALASPEED
- 1.7.20. Setting Speed Ratio Sensor
- 1.8. Lubricants
- 1.8.1. Lubricant Storage
- 1.8.2. Alternative and Synthetic Lubricants
- 1.8.3. Mixing of Lubricants
- 1.9. Lubrication and Maintenance
- 1.9.1. Lubrication Symbols
- 1.9.2. Lubrication and Maintenance
- 1.9.2.1. Care and Maintenace of belts
- 1.9.3. Every 50 Hours Of Operation
- 1.9.4. Chains Every 200 Hours of Operation
- 1.10. Troubleshooting
- 1.10.1. Belt Pickup
- 1.10.2. Active Header Control (AHC)
- 1.11. Service
- 1.11.1. Hydraulic Cylinder Safety Stop
- 1.11.2. Belt Pickup/Pump Belt Adjustment (10 Series Combines)
- 1.11.3. Replacing Pickup Belts
- 1.11.4. Replacing Pickup Fingers
- 1.11.5. Replacing Auger Fingers and Retainers
- 1.11.6. Header Warning Light Bulb Replacement
- 1.11.7. Rephasing Windrow HoldDown Cylinders
- 1.12. Storage
- 1.12.1. End Of Season Service
- 1.12.2. Beginning Of Season
- 1.13. Specifications
- 1.13.1. Belt Pickup Specifications
- 1.13.2. Header Serial Number
- 1.13.3. Keep Proof of Ownership
- 1.13.4. Keep Machines Secure
- 1.13.5. Metric Bolt and Screw Torque Values
- 1.13.6. Unified Inch Bolt and Screw Torque Values
- 1.14. John Deere Service Literature Available
- 1.14.1. Technical Information
- 1.15. John Deere Service Keeps You On The Job
- 1.15.1. John Deere Is At Your Service
- 2. Page Numbers
- 2.1. Section 05
- 2.2. Section 10
Related products
-50%
Original price was: $20.$10Current price is: $10.
-50%
Original price was: $20.$10Current price is: $10.
-50%
Original price was: $20.$10Current price is: $10.
-50%
Original price was: $20.$10Current price is: $10.
