John Deere 500R Rotary Platform Operator Manual OMFH323618

Description

• Model List:
  • 500R Rotary Platform

• 1. Contents
• 1.0.1. Recognize Safety Information
• 1.0.2. Understand Signal Words
• 1.0.3. Follow Safety Instructions
• 1.0.4. Spanish Safety Signs and Operators Manual
• 1.0.5. Replace Safety Signs
• 1.0.6. Keep Riders and Children Off Machine
• 1.0.7. Ballast for Safe Ground Contact
• 1.0.8. Prepare for Emergencies
• 1.0.9. In Case of Fire
• 1.0.10. Wear Protective Clothing
• 1.0.11. Stay Clear of Platform
• 1.0.12. Use Safety Lights and Devices
• 1.0.13. Transport Machine with Platform or Weight Box Attached
• 1.0.14. Avoid Injury From Thrown Objects
• 1.0.15. Practice Safe Maintenance
• 1.0.16. Remove Paint Before Welding or Heating
• 1.0.17. Avoid Heating Near Pressurized Fluid Lines
• 1.0.18. Install All Shields and Guardssss
• 1.0.19. Avoid HighPressure Fluids
• 1.0.20. Decommissioning Proper Recycling and Disposal of Fluids and Components
• 1.0.21. Remove Accumulated Crop Debris
• 1.0.22. Support Machine Properly
• 1.0.23. Service Drive Belts Safely
• 1.0.24. Use Proper Lifting Equipment
• 1.0.25. Avoid Backover Accidents
• 1.0.26. Before Operating
• 1.0.27. Use Proper Tools
• 1.0.28. Practice Safe Service Procedures
• 1.1. Safety Sign Location
• 1.1.1. Replace Safety Signs
• 1.1.2. Safety Signs
• 1.2. Attaching and Detaching Platform
• 1.2.1. Attach Platform (R450)
• 1.2.2. Attach Draper Platform (W235 and W260)
• 1.2.3. Adjust Draper Setup (W235 and W260)
• 1.2.4. Balance Platform (R450)
• 1.2.5. Balance Draper Platform (W235 and W260)
• 1.2.6. Detach Platform (R450)
• 1.2.7. Detach Platform (W235 and W260)
• 1.3. Operating Platform
• 1.3.1. Prestart Checks
• 1.3.2. Breakin Rotary Platform
• 1.3.3. Keep Riders and Children Off Machine
• 1.3.4. Follow Safe Operating Procedures
• 1.3.5. Raise and Lower Platform
• 1.3.6. Adjust Platform Cutterbar Angle
• 1.3.7. Adjust Platform Float
• 1.3.8. Adjust Platform Cutterbar Speed
• 1.3.9. Raise and Lower Front Doors and Curtains
• 1.3.10. Adjust Gauge Shoes
• 1.3.11. Platform Settings for Various Crop Conditions
• 1.3.12. Adjust Windrow Width and Shape
• 1.3.13. Adjust Roll Timing
• 1.3.14. Adjust Roll Pressure
• 1.3.15. Adjust Roll Spacing
• 1.3.16. Unplug Rolls
• 1.3.17. Change Conditioner Speed
• 1.3.18. Adjust Conditioner Drive Belt Tension
• 1.3.19. Adjust Auger Drive Belt Tension
• 1.3.20. Shear Disk Driver When Operating In the Field
• 1.4. Fire Prevention
• 1.4.1. Recommended Fire Prevention
• 1.4.2. Fire Extinguisher Operation
• 1.4.3. Prepare for Emergencies
• 1.4.4. Remove Accumulated Crop Debris
• 1.4.5. Fire Extinguisher
• 1.4.6. Fire Extinguisher Location
• 1.4.7. In Case of Fire
• 1.5. Lubrication and Maintenance
• 1.5.1. Cutterbar Oil
• 1.5.2. Cutterbar Drive and Conditioner Drive Gear Case Oil
• 1.5.3. Alternative and Synthetic Lubricants
• 1.5.4. Mixing of Lubricants
• 1.5.5. Lubricant Storage
• 1.5.6. Observe Lubrication Symbols
• 1.5.7. Service Intervals
• 1.5.8. Daily Service
• 1.5.9. Every 10 Hours Service
• 1.5.10. First 50 Hours Service
• 1.5.11. Every 50 Hours Service
• 1.5.12. Every 100 Hours Service
• 1.5.13. Every 200 Hours Service
• 1.5.14. Every 800 Hours Service
• 1.6. Troubleshooting
• 1.6.1. Troubleshooting
• 1.7. Service
• 1.7.1. Practice Safe Service Procedures
• 1.7.2. Keep Service Area Clean
• 1.7.3. Care of VBelts
• 1.7.4. Tighten Bearing Locking Collars
• 1.7.5. Platform Wire Harness Diagram
• 1.7.6. Wire Harness Adapter
• 1.7.7. Warning and Turn Light Jumpers
• 1.7.8. Remove and Install Upper Roll Driveline
• 1.7.9. Remove and Install Lower Roll Driveline
• 1.7.10. Check Converging Drum Wear
• 1.7.11. Remove and Install Converging Drums
• 1.7.12. Adjust Stripper to Auger
• 1.7.13. Remove and Install Converging Drum Drive Belts
• 1.7.14. Replace Conditioner Drive Gear Case Belt
• 1.7.15. Check Disk Wear
• 1.7.16. Remove Disks
• 1.7.17. Install and Synchronize Disks
• 1.7.18. Replace LeftHand End Disk Driver
• 1.7.19. Replace Intermediate Disk Drivers
• 1.7.20. Replace RightHand End Disk Driver
• 1.7.21. Check Knives and Knife Bolts for Wear
• 1.7.22. Remove and Install Knives
• 1.7.23. Replace Wear Cap
• 1.7.24. Replace Crop Accelerator
• 1.7.25. Remove and Install Gauge Shoes
• 1.8. Storage
• 1.8.1. Prepare Platform for Storage
• 1.8.2. Remove Platform from Storage
• 1.9. Specifications
• 1.9.1. Platform Specifications(Specifications and design subject to change without notice.)
• 1.9.2. Metric Bolt and Screw Torque Values
• 1.9.3. Unified Inch Bolt and Screw Torque Values
• 1.9.4. Eurasian Economic Union
• 1.9.5. Customs UnionEAC Compliance Label Location
• 1.9.6. Machine Design Life
• 1.10. Machine Identification Numbers
• 1.10.1. Serial Number Plate
• 1.10.2. Serial Number Plate Description
• 1.10.3. Record Platform Serial Number
• 1.10.4. Keep Proof of Ownership
• 1.10.5. Keep Machines Secure
• 1.11. John Deere Service Literature Available
• 1.11.1. Technical Information
• 1.12. John Deere Service Keeps You On The Job
• 1.12.1. John Deere Is At Your Service
• 2. Page Number
• 2.1. Section 05
• 2.2. Section 10
• 2.3. Section 15
• 2.4. Section 20
• 2.5. Section 25
• 2.6. Section 30
• 2.7. Section 40
• 2.8. Section 45
• 2.9. Section 50
• 2.10. Section 55
• 2.11. Section 60