Description
-
Model List:
- R160 Rotary Disk Mower
- R200 Rotary Disk Mower
- 1. Contents
- 1.0.1. Recognize Safety Information
- 1.0.2. Understand Signal Words
- 1.0.3. Follow Safety Instructions
- 1.0.4. Operate Mower Safely
- 1.0.5. Keep Riders Off Machine
- 1.0.6. Prepare for Emergencies
- 1.0.7. Wear Protective Clothing
- 1.0.8. Handle Chemical Products Safely
- 1.0.9. Stay Clear of Rotating Drivelines
- 1.0.10. Avoid Injury from Thrown Objects
- 1.0.11. Use Safety Lights and Devices
- 1.0.12. Tow Loads Safely
- 1.0.13. Practice Safe Maintenance
- 1.0.14. Remove Paint Before Welding or Heating
- 1.0.15. Avoid Heating Near Pressurized Fluid Lines
- 1.0.16. Avoid HighPressure Fluids
- 1.0.17. Store Attachments Safely
- 1.0.18. Decommissioning Proper Recycling and Disposal of Fluids and Components
- 1.0.19. Safety Features
- 1.0.20. Safety Signs
- 1.1. Preparing the Tractor
- 1.1.1. Tractor PTO Speed
- 1.1.2. Position Tractor Drawbar
- 1.1.3. Adjust Tractor Hitch
- 1.1.4. Set Tractor Hydraulic Outlets
- 1.1.5. Check Ballast, Wheel Spacing, and Tire Inflation
- 1.1.6. Use Implement Codes
- 1.1.7. Use Drawbar Shield
- 1.1.8. Make Drawbar Shield
- 1.2. Preparing the Mower
- 1.2.1. Position Lower Hitch Pins
- 1.3. Attaching and Detaching
- 1.3.1. Attach Mower Hitch to Tractor Draft Link Hitch
- 1.3.2. Telescoping Driveline
- 1.3.3. Assemble Main PTO Driveline Splined Telescoping Members (If Necessary)
- 1.3.4. Attach PTO Driveline
- 1.3.5. Attach to Tractor Hydraulic System
- 1.3.6. Attach PullRope
- 1.3.7. Detach Mower From Tractor
- 1.4. Transporting
- 1.4.1. Prepare Mower for Transport
- 1.4.2. Keep Riders Off Machine
- 1.5. Operating the Mower
- 1.5.1. Prepare Mower for Field Operation
- 1.5.2. Prestart Checks
- 1.5.3. Adjust Main Frame Height
- 1.5.4. Break in Mower
- 1.5.5. Keep Riders Off Machine
- 1.5.6. Follow Safe Operating Procedures
- 1.5.7. Adjust Cut Height
- 1.5.8. Adjust Mower for Adverse Field Conditions
- 1.5.9. Reset and Adjust Breakaway Latch
- 1.5.10. Adjust Compensating Spring Tension
- 1.5.11. Raise and Lower Pivoting Cover Support
- 1.5.12. Adjust Swath Wheel
- 1.6. Attachments
- 1.6.1. High Skid Shoe Kit
- 1.6.2. Drawbar Shield
- 1.7. Lubrication and Maintenance
- 1.7.1. Lubricate and Maintain Machine Safely
- 1.7.2. Cutterbar and Gear Case Oil
- 1.7.3. Alternative and Synthetic Lubricants
- 1.7.4. Mixing of Lubricants
- 1.7.5. Lubricant Storage
- 1.7.6. Observe Lubrication Symbols
- 1.7.7. Perform Lubrication and Maintenance
- 1.7.8. Every 8 Hours
- 1.7.9. Every 20 Hours
- 1.7.10. Every 24 Hours (Daily)
- 1.7.11. Every 40 Hours
- 1.7.12. Every 50 Hours
- 1.7.13. Every 200 Hours
- 1.7.14. As Required
- 1.8. Troubleshooting
- 1.8.1. Troubleshooting
- 1.9. Service
- 1.9.1. Practice Safe Service Procedures
- 1.9.2. Keep Service Area Clean
- 1.9.3. Adjust Drive Belts
- 1.9.4. Replace Drive Belts
- 1.9.5. Inspect Knives
- 1.9.6. Check Knife Wear
- 1.9.7. Check Knife Mounting
- 1.9.8. Remove Knives
- 1.9.9. Install Knives
- 1.9.10. Direction of Knife Rotation
- 1.9.11. Check Knife Bolts
- 1.9.12. Replace Knife Bolts
- 1.9.13. Check Knife Nuts
- 1.9.14. Remove Disks
- 1.9.15. Remove Converging Cone Disk
- 1.9.16. Install and Synchronize Disks and Converge Cones Disk
- 1.9.17. Interchange Disks
- 1.10. Storage
- 1.10.1. Storing Mower (End of Season)
- 1.10.2. Remove Mower from Storage (Beginning of Season)
- 1.11. Specifications
- 1.11.1. R160 and R200 Rotary Disk Mower Specifications (Specifications and design are subject to change without notice.)
- 1.11.2. Keep Proof of Ownership
- 1.11.3. Keep Machines Secure
- 1.11.4. Metric Bolt and Screw Torque Values
- 1.11.5. Unified Inch Bolt and Screw Torque Values
- 1.12. John Deere Service Keeps You On The Job
- 1.12.1. John Deere Is At Your Service
- 2. Page Number
- 2.1. Section 05
- 2.2. Section 10
- 2.3. Section 15
- 2.4. Section 20
- 2.5. Section 25
- 2.6. Section 30
- 2.7. Section 35
- 2.8. Section 40
- 2.9. Section 45
- 2.10. Section 50
- 2.11. Section 55
- 2.12. Section 60
