Manitou Dana Axle Type 211 Dual Brake Service Manual 647904EN

Description

• Model List:
  • Dana Axle Type 211 Dual Brake

• 1. Page de garde / Front page
• 1.1. ASM0194E_Rev.08 211.pdf
• 1.1.1. Contents
• 1.1.2. Introduction
• 1.1.2.1. Version tracking
• 1.1.2.2. Manual applicability and supported models
• 1.1.3. Specifications
• 1.1.3.1. Definition of viewpoints
• 1.1.3.2. Data plate
• 1.1.3.3. Conversion tables
• 1.1.3.3.1. Units of pressure
• 1.1.3.3.2. Units of weight
• 1.1.3.3.3. Units of torque
• 1.1.3.4. Torque specifications
• 1.1.3.4.1. Coarse pitch
• 1.1.3.4.2. Fine pitch
• 1.1.3.4.3. Wheel nut tightening torques
• 1.1.4. Maintenance
• 1.1.4.1. Maintenance points
• 1.1.4.2. Oil draining mandatory procedure
• 1.1.4.2.1. Central housing
• 1.1.4.2.2. Planetary gear reduction
• 1.1.4.3. Endstop plier setting
• 1.1.4.3.1. Retaining snap ring for bores
• 1.1.4.3.2. Retaining snap ring for shafts
• 1.1.4.4. Input seal greasing
• 1.1.4.4.1. Handling instruction greasing 1
• 1.1.4.4.2. Handling instruction greasing 2
• 1.1.4.5. Maintenance intervals
• 1.1.4.6. Lubricant sealant specifications
• 1.1.5. Safety precautions
• 1.1.6. Planetary reduction 16 and steering knuckle (flanged nuts version)
• 1.1.7. Planetary reduction 14,23
• 1.1.8. Steering cylinder
• 1.1.9. Flanged reduction gear 603 type integral 603 input gear
• 1.1.10. Bevel pinion normal flange and nut revolution counter version
• 1.1.10.1. Exploded view
• 1.1.10.2. Disassembly
• 1.1.10.3. Assembly
• 1.1.10.4. Normal flange version
• 1.1.10.5. Revolution counter version
• 1.1.11. Swinging support
• 1.1.11.1. Exploded view
• 1.1.11.2. Disassembly
• 1.1.11.3. Assembly
• 1.1.12. Service and sahr incoming disc brake
• 1.1.12.1. Exploded view
• 1.1.12.2. Disassembly
• 1.1.12.3. Assembly
• 1.1.12.4. Checking wear and replacing the braking pads
• 1.1.12.5. Caliper assembly and setting
• 1.1.13. Incoming drum brake
• 1.1.14. Normal differential
• 1.1.14.1. Exploded view
• 1.1.14.2. Disassembly
• 1.1.14.3. Assembly
• 1.1.15. Limited slip differential unit 45
• 1.1.15.1. Exploded view
• 1.1.15.2. Disassembly
• 1.1.15.3. Assembly
• 1.1.16. Bevel pinion flanged to reduction gear 603
• 1.1.17. Ring and pinion adjusting version pinion integral and double arm
• 1.1.17.1. Exploded view
• 1.1.17.2. Install and adjust
• 1.1.18. Manual emergency release
• 1.1.18.1. Exploded view
• 1.1.18.2. Manual emergency release
• 1.1.19. Adjustment after manual release
• 1.1.19.1. Exploded view
• 1.1.19.2. Adjustment after manual release
• 1.1.20. Brake wear check procedure
• 1.1.20.1. Exploded view
• 1.1.20.2. Brake wear check procedure
• 1.1.20.3. Special tools
• 1.1.21. Service and negative brake
• 1.1.22. Separate pinion cover for flanged gearbox
• 1.1.22.1. Exploded view
• 1.1.22.2. Disassembly
• 1.1.22.3. Assembly
• 1.1.22.3.1. Calculating pinion bearings rolling torque
• 1.1.22.3.2. Calculating pinion center distance
• 1.1.23. United pinion cover for flanged gearbox
• 1.1.23.1. Exploded view
• 1.1.23.2. Disassembly
• 1.1.23.3. Assembly
• 1.1.23.3.1. Calculating pinion center distance
• 1.1.23.3.2. Calculating pinion bearings rolling torque
• 1.1.23.4. Special tools
• 1.1.24. Steering knuckle king pin preloaded by belleville washers
• 1.1.25. Flanged reduction gear 315 type integral input gear (din flange)
• 1.1.25.1. Exploded view
• 1.1.25.2. Disassembly
• 1.1.25.3. Assembly
• 1.1.26. Flanged reduction gear 315 type interchangable input gear (end yoke flange)
• 1.1.27. Differential with block to spheres 100 (last version)
• 1.1.27.1. Exploded view
• 1.1.27.2. Disassembly
• 1.1.27.3. Assembly
• 1.1.28. Counter revolution sensor (dropin type)
• 1.1.28.1. Exploded view
• 1.1.28.2. Disassembly
• 1.1.28.3. Assembly