John Deere 615P Belt Pickup Operator Manual OMHXE147019

John Deere 615P Belt Pickup Operator Manual OMHXE147019-2

John Deere 615P Belt Pickup Operator Manual OMHXE147019-3

John Deere 615P Belt Pickup Operator Manual OMHXE147019

Type Of Manual: Operator Manual
Manual ID: OMHXE147019
Format: PDF
Size: 2.8MB
Number of Pages: 60

Category: John Deere Operators Manuals PDF Tag: Agricultural

Description

Model List:
- 615P Belt Pickup

1. Introduction
1.1. Foreword
1.2. A Message to Our Customers
1.3. Identification View
2. Safety Features
2.1. Header Safety Features
2.2. Recognize Safety Information
2.3. Understand Signal Words
2.4. Follow Safety Instructions
2.5. French and Spanish Safety Signs and Operators Manual
2.6. Ballasting for Safe Ground Contact
2.7. Parking and Leaving the Machine
2.8. Prepare for Emergencies
2.9. Wear Protective Clothing
2.10. Stay Clear of Harvesting Units
2.11. Use Safety Lights and Devices
2.12. Transport Combine With Header Safely
2.13. Road Transport Disconnect Switch
2.14. Practice Safe Maintenance
2.15. Remove Paint Before Welding or Heating
2.16. Avoid Heating Near Pressurized Fluid Lines
2.17. Avoid Contact With Moving Parts
2.18. Stay Clear of Rotating Drivelines
2.19. Guards and Shields
2.20. Avoid HighPressure Fluids
2.21. Service Accumulator Systems Safely
2.22. Service Machines Safely
2.23. Service Drive Belts Safely
2.24. Protect Against High Pressure Spray
2.25. Service Tires Safely
2.26. Decommissioning Proper Recycling and Disposal of Fluids and Components
2.27. Support Machine Properly
2.28. Store Attachments Safely
3. Safety Signs
3.1. Rear View Decals
3.2. Side View Decals
3.3. Replace Safety Signs
4. Transporting
4.1. Transporting on Trailer
4.2. Transporting on Combine
5. Attaching and Detaching
5.1. Rear Auger Stripper Extension Location
5.2. Attaching Header to Feeder House
5.3. Detaching Header from Feeder House
6. Calibration and Settings
6.1. When to Calibrate
6.2. Before Calibration
6.3. Calibration Error Codes
6.4. Air Spring Setup (Prior to Header Calibration)
6.5. User Calibration Procedures
6.6. Adjusting Feeder House Drop Rate and Sensitivity
7. Operating the Belt Pickup
7.1. Armrest Functions
7.2. Active Header Control DisplayFeatures
7.3. Description of Automatic Header Height Control Systems
7.4. Pickup Speed
7.5. Pickup Height
7.6. Pickup Pitch
7.7. Pickup Pitch (Normal Windrow Condition)
7.8. Pickup Pitch (Poor Windrow Condition)
7.9. Pickup Pitch (Rocky Conditions)
7.10. Adjusting Windrow HoldDown (Wind Screen)
7.11. Wet or Muddy Terrain (Light Gauge Wheel Pressure)
7.12. Large and Uneven Windrows
8. Adjustments Belt Pickup
8.1. Service Tires Safely
8.2. Adjusting Air Springs
8.3. Periodic Checking of Air Spring Pressure
8.4. Adjusting Windrow HoldDown (Wind Screen) Fixed Position
8.5. Adjusting Auger Position
8.6. Adjusting Auger Height
8.7. Adjusting Auger Fore/Aft (Left Side)
8.8. Adjusting Auger Fore/Aft (Right Side)
8.9. Adjusting Finger Timing
8.10. Adjusting Rear Stripper
8.11. Adjusting Floor Stripper
8.12. Adjusting Auger Chain Tension
8.13. Adjusting Transfer Belt Tension
8.14. Adjusting Picking Belt Tension
8.15. Belt Tracking Issues
8.15.1. Tracking Issues
8.15.2. Belt Drift
8.15.3. Correcting Belt Wave From Over Tensioning
8.16. Adjusting DialASpeed Belt Speed Ratio
8.17. Setting Speed Ratio Sensor
9. Lubrication
9.1. Lubricant Storage
9.2. Alternative and Synthetic Lubricants
9.3. Mixing of Lubricants
10. Lubrication and Maintenance
10.1. Lubrication Symbols
10.2. Care and Maintenance of Belts
10.3. Lubrication Interval Chart
10.4. Every 50 Hours of Operation
10.5. Every 200 Hours of Operation
11. Service
11.1. Hydraulic Cylinder Safety Stop
11.1.1. Manual Feeder House Fore/Aft Tilt
11.1.2. Hydraulic Feeder House Fore/Aft Tilt
11.2. Open Side Shield
11.3. Replacing Pickup Belts
11.4. Replacing Pickup Fingers
11.5. Replacing Auger Fingers and Retainers
11.6. Header Warning Light Bulb Replacement
11.7. Rephasing Windrow HoldDown Cylinders
12. Troubleshooting
12.1. Belt Pickup
12.2. Active Header Control (AHC)
13. Storage
13.1. End Of Season Service
13.2. Beginning Of Season Service
14. Specifications
14.1. Specifications
14.2. Keep Machines Secure
14.3. Header Identification Number
14.4. Keep Proof of Ownership
14.5. Unified Inch Bolt and Screw Torque Values
14.6. Metric Bolt and Screw Torque Values
15. John Deere Service Literature Available
15.1. Technical Information
16. John Deere Service Keeps You On The Job
16.1. John Deere Is At Your Service

John Deere 615P Belt Pickup Operator Manual OMHXE147019

Description

Related products

Login