John Deere 600 Series Rigid and Flex Cutting Platforms Operator Manual OMHXE175613-1

John Deere 600 Series Rigid and Flex Cutting Platforms Operator Manual OMHXE175613-2

John Deere 600 Series Rigid and Flex Cutting Platforms Operator Manual OMHXE175613-3

John Deere 600 Series Rigid and Flex Cutting Platforms Operator Manual OMHXE175613

Type Of Manual: Operator Manual
Manual ID: OMHXE175613
Format: PDF
Size: 16.8MB
Number of Pages: 104

Category: John Deere Operators Manuals PDF Tag: Agricultural

Description

Model List:
- 600 Series Rigid and Flex Cutting Platforms

1. Introduction
1.1. Foreword
1.2. Company Info
1.3. A Message to Our Customers
1.4. Intended Use
1.5. Trademarks
2. Identification View
2.1. Identification View
3. Safety Features
3.1. Header Safety Features
3.2. Recognize Safety Information
3.3. Understand Signal Words
3.4. Follow Safety Instructions
3.5. French and Spanish Safety Signs and Operators Manual
3.6. Replace Safety Signs
3.7. Operator Ability
3.8. Ballasting for Safe Ground Contact
3.9. Parking and Leaving the Machine
3.10. Prepare for Emergencies
3.11. Wear Protective Clothing
3.12. Stay Clear of Harvesting Units
3.13. Keep Hands Away From Knives
3.14. Use Safety Lights and Devices
3.15. Transport Combine with FrontEnd Equipment Attached Safely
3.16. Road Transport Disconnect Switch
3.17. Practice Safe Maintenance
3.18. Remove Paint Before Welding or Heating
3.19. Avoid Heating Near Pressurized Fluid Lines
3.20. Avoid Contact With Moving Parts
3.21. Stay Clear of Cutterbar When Rotating Auger
3.22. Stay Clear of Rotating Drivelines
3.23. Guards and Shields
3.24. Avoid HighPressure Fluids
3.25. Service Accumulator Systems Safely
3.26. Service Machines Safely
3.27. Service Belts and Chains Safely
3.28. Protect Against High Pressure Spray
3.29. Decommissioning Proper Recycling and Disposal of Fluids and Components
3.30. Support Machine Properly
3.31. Store Attachments Safely
4. Safety SignsExcept North America
4.1. Pictorial Safety Signs
4.2. Replace Safety Signs
4.3. Recognize Safety Information
4.4. Operators Manual
4.5. Hydraulic Oil and Gas Under Pressure
4.6. Rotating Driveline
4.7. Reel Safety Stops
4.8. Side Shield
4.9. Cutterbar Movement
4.10. Header Entanglement
5. Safety SignsNorth America Only
5.1. Safety Signs LocationFlex Platforms Only
6. Attaching and Detaching
6.1. Location of the Rear Auger Stripper Extension
6.2. Identification of Coupling Type
6.3. Coupling Header to CombineMulticoupler
6.4. Coupling Header to CombineMultiPoint
6.5. Removing Header from Feeder HouseMulticoupler
6.6. Removing Header from Feeder HouseMultiPoint
6.7. Unlocking Feeder House Manually
6.8. Location of Locking Cable Shear Screws
7. Transporting
7.1. Transporting on Trailer
7.2. Transporting on Combine
8. Operating the Platform
8.1. Choice of Harvesting Time
8.2. Cutting Platform Operation
8.3. Description of Automatic Header Height Control Systems
8.4. Operating Flex PlatformsHYDRAFLEX System Pressure
8.5. Header Height SensingHYDRAFLEX Heads with Auxiliary Sensors
8.6. Wiring Harness InformationOnly for Headers Equipped with Height Sensor
8.7. Operating Flex Platform in Rigid Mode
8.8. Auxiliary Sensor Arm Operating Positions
8.9. Flex System Lock for Rigid Mode OperationOnly for Headers Equipped with Height Sensor
8.10. Operating and Servicing RequirementsOnly for Headers Equipped with Height Sensor
8.11. Checking Platform Speeds
8.12. Reel Operation
8.13. Cutting Platform Controls
8.14. Position Warning Lights for Field Operation
8.15. Combining Oats, Sorghum, Wheat, and Sunflowers in Dry Ground Conditions
8.16. Combining Oats, Sorghum, and Wheat in Damp or Wet Ground Conditions
8.17. Combining Oats, Sorghum, Barley, and Wheat in Short, Thin CropsRigid Platforms
8.18. Combining RiceRigid Platforms
8.19. Combining SoybeansFlex Platforms
9. Attachments and Options
9.1. Auger Flight Extensions (Attachment)Flex Platforms
9.2. Auger Speeds (Attachment)
9.3. Stubble Lights (Optional)Flex Platforms
9.4. Fine Serrated Knife (Optional)
9.5. Knife Assemblies with LongShort Sections (Optional)
9.6. Knife Drive Sheaves (Attachment)
9.7. HeavyDuty Wear PlatesRigid Platforms
9.8. Reel Position Resume (Attachment)S Series Combines
9.9. Short Dividers (Optional)Flex Platforms
9.10. Spare Knife Storage (Attachment)
9.11. Raised Height Skid Shoes (Optional)
9.12. Low Stone Dam (Attachment or Option)
9.13. High Stone Dam (Attachment or Option)
10. Calibration and Settings
10.1. When to Calibrate
10.2. Calibration Error Codes
10.3. Calibration Procedures
11. Adjustments Flex Platform
11.1. Adjust Platform Cutterbar/Skid Plate Tilt
11.2. Adjusting Head Drop Rate
11.3. Standard PERMAGLIDE Divider Points
11.4. Adjusting Standard PERMAGLIDE Divider Point Height
11.5. SidetoSide Adjustment of Front Section of Standard PERMAGLIDE Point
12. Adjustments Rigid Platform
12.1. Cutterbar Positions
12.2. Adjusting Cutterbar Fore/Aft
12.3. Adjusting Platform Cutterbar/Skid Plate Tilt
12.4. Adjusting Head Drop Rate
13. Adjustments Auger and Stripper
13.1. Auger Configuration Information Sign
13.2. Remove Knife Drive Belt from Drive Sheave
13.3. Adjusting Auger Position
13.4. Adjusting Auger Height
13.5. Adjusting Auger Fore/Aft
13.6. Adjusting Center Auger Finger Timing
13.7. Adjusting Rear Stripper
13.8. Adjusting Floor Stripper
13.9. Adjusting Auger Chain
14. Adjustments Reel
14.1. Adjust Reel Fingers
14.2. Adjusting Minimum Reel Height and Leveling Reel
14.3. Adjusting Width Between Reel Arms
14.4. Adjusting Reel Fore/Aft and Lift Cylinders
14.5. Rephase Hydraulic Reel Fore/Aft
14.6. Rephasing Reel Lift Cylinders
14.7. Bleeding the Reel Lift Cylinder System
14.8. Adjusting Reel Speed Ratio Sensor
14.9. Adjusting Reel Drive Gear
14.10. Adjusting Platform Height Restoring System
15. Lubricants
15.1. Gear Oil
15.2. Alternative and Synthetic Lubricants
15.3. Mixing of Lubricants
15.4. Lubricant Storage
15.5. Multipurpose Grease
16. Lubrication and Service
16.1. Lubrication Intervals Information Sign
16.2. Lubrication Symbols
16.3. Care and Maintenance of Belts
16.4. Every 50 Hours of Operation
16.5. Every 200 Hours of Operation
16.6. Every 400 Hours of Operation
17. Troubleshooting
17.1. Cutterbar Difficulties
17.2. Down and Tangled Crops Difficulties
17.3. Feeder House Difficulties
17.4. Auger Difficulties
17.5. Cutting Difficulties
17.6. Reel Difficulties
17.7. Hydraulic System Difficulties
17.8. ACTIVE HEADER CONTROL
18. Servicing
18.1. Safe Cutting Platform Operation
18.2. Reel Safety Stops
18.3. Opening and Closing Right and LeftHand Shields
18.4. Remove and Install Knife Drive Belt
18.5. Adjusting Knife Drive Belt Tension
18.6. Replacing Cutterbar Knife
18.7. Knife and Knife Drive Alignment
18.8. Knife HoldDown Clearance
18.9. Replacing Knife Sections
18.10. Replacing Auger Fingers and Retainers
18.11. Stubble Light Bulb Replacement
18.12. Header Warning Light Bulb Replacement
18.13. Bleeding HydraFlex SystemFlex Headers
19. Storage
19.1. End of Season Service
19.2. Beginning of Season Service
19.3. Prepare Machine for Storage
20. Specifications
20.1. SpecificationsRigid Platforms
20.2. Dimensions/WeightRigid Cutting Platforms
20.3. SpecificationsFlex Platforms
20.4. Dimensions/WeightsFlex Cutting Platforms
20.5. Metric Bolt and Screw Torque Values
20.6. Unified Inch Bolt and Screw Torque Values
20.7. Machine Design Life
20.8. EU Declaration of Conformity (for Products Sold into the European Union)
20.9. UK Declaration of Conformity (for Products Sold into the United Kingdom)
20.10. Eurasian Economic Union (for Products Sold into These Countries)
21. Serial Number
21.1. Identification Numbers
21.2. Identification Plate
21.3. Keep Proof of Ownership
21.4. Interpreting Machine Serial Number
21.5. Product Identification Number
22. John Deere Service Literature Available
22.1. Technical Information
23. John Deere ServiceKeeps You on the Job
23.1. John Deere Parts
23.2. The Right Tools
23.3. WellTrained Technicians
23.4. Prompt Service

Rate this product

John Deere 600 Series Rigid and Flex Cutting Platforms Operator Manual OMHXE175613

Description

Related products

Login