Description
-
Model List:
- 600F Series Cutting Platform
- 1. Contents
- 1.1. Safety Features
- 1.1.1. Header Safety Features
- 1.1.2. Recognize Safety Information
- 1.1.3. Understand Signal Words
- 1.1.4. Follow Safety Instructions
- 1.1.5. Spanish Safety Signs and Operators Manual
- 1.1.6. Ballasting for Safe Ground Contact
- 1.1.7. Parking and Leaving the Machine
- 1.1.8. Prepare for Emergencies
- 1.1.9. Wear Protective Clothing
- 1.1.10. Stay Clear of Harvesting Units
- 1.1.11. Keep Hands Away From Knives
- 1.1.12. Use Safety Lights and Devices
- 1.1.13. Transport Combine With Header Safely
- 1.1.14. Road Transport Disconnect Switch
- 1.1.15. Practice Safe Maintenance
- 1.1.16. Remove Paint Before Welding or Heating
- 1.1.17. Avoid Heating Near Pressurized Fluid Lines
- 1.1.18. Avoid Contact With Moving Parts
- 1.1.19. Stay Clear of Cutterbar When Rotating Auger
- 1.1.20. Stay Clear of Rotating Drivelines
- 1.1.21. Guards and Shields
- 1.1.22. Avoid HighPressure Fluids
- 1.1.23. Service Accumulator Systems Safely
- 1.1.24. Service Machines Safely
- 1.1.25. Service Drive Belts Safely
- 1.1.26. Protect Against High Pressure Spray
- 1.1.27. Decommissioning Proper Recycling and Disposal of Fluids and Components
- 1.1.28. Support Machine Properly
- 1.1.29. Store Attachments Safely
- 1.2. Safety Signs
- 1.2.1. Rear View Decals
- 1.2.2. Rear View Decals Continued
- 1.2.3. Side View Decals
- 1.2.4. Replace Safety Signs
- 1.3. Transporting
- 1.3.1. Transporting on Trailer
- 1.3.2. Transporting on Combine
- 1.4. Attaching and Detaching
- 1.4.1. Rear Auger Stripper Extension Location
- 1.4.2. Attaching Header to Feeder House
- 1.4.3. Detaching Header from Feeder House
- 1.5. Calibration and Settings
- 1.5.1. When to Calibrate
- 1.5.2. Calibration Error Codes
- 1.5.3. Calibration Procedures
- 1.5.4. Adjusting Feeder House Drop Rate and Sensitivity
- 1.6. Operating the Platform
- 1.6.1. Cutting Platform Operation
- 1.6.2. Setting Backshaft Speed
- 1.6.3. Armrest Functions
- 1.6.4. Active Header Control DisplayFeatures
- 1.6.5. Description of Automatic Header Height Control Systems
- 1.6.6. Operating HydraFlex PressureFlex Platforms
- 1.6.7. Header Height Sensing HYDRAFLEX Heads with Auxiliary Sensors
- 1.6.8. Operating Flex Platform in Rigid Mode
- 1.6.9. Auxiliary Sensor Arm Operating Positions
- 1.6.10. HydraFlex Pressure Manual Adjust Switch
- 1.6.11. Position Warning Lights for Field Operation
- 1.6.12. Harvesting SoybeansFlex Platforms
- 1.6.13. Harvesting Sorghum and Sunflowers in Dry Ground Conditions
- 1.6.14. Harvesting Oats, Sorghum and Wheat in Damp or in Wet/Weedy Conditions (All Platforms)
- 1.7. Attachments and Options
- 1.7.1. Auger Flight Extensions (Attachment)
- 1.7.2. Auger Speed Increase or Decrease (Attachment)
- 1.7.3. Stubble Lights (Attachment)
- 1.7.4. Spare Knife Storage (Optional)
- 1.7.5. Fine Serrated Knife (Optional)
- 1.7.6. Knife Assemblies with LongShort Sections (Optional)
- 1.7.7. Knife Drive Sheaves (Attachment)
- 1.7.8. Reel Position Resume (Attachment)
- 1.7.9. Short Dividers (Attachment)
- 1.7.10. Low Stone Dam (Attachment or Option)
- 1.7.11. High Stone Dam (Attachment or Option)
- 1.7.12. Raised Height Skid Shoes (Optional)
- 1.8. Adjustments Flex Platform
- 1.8.1. Bleeding HydraFlex System
- 1.8.2. Standard PermaGlide Divider and Divider Point
- 1.8.3. Height Adjustment of PermaGlide Divider Assembly
- 1.8.4. SidetoSide Adjustment of PermaGlide Divider Assembly
- 1.9. Adjustments Auger and Stripper
- 1.9.1. Remove Knife Drive Belt From Drive Sheave
- 1.9.2. Adjusting Auger Position
- 1.9.3. Adjusting Auger Height
- 1.9.4. Adjusting Auger Fore/Aft
- 1.9.5. Adjusting Center Auger Finger Timing
- 1.9.6. Adjusting Rear Stripper
- 1.9.7. Adjusting Floor Stripper
- 1.9.8. Adjusting Auger Chain
- 1.10. Adjustments Reel
- 1.10.1. Adjust Reel Fingers
- 1.10.2. Adjusting Minimum Reel Height and Leveling Reel
- 1.10.3. Adjusting Reel Fore/Aft and Lift Cylinders
- 1.10.4. Rephasing Reel Fore/Aft Cylinders
- 1.10.5. Rephasing Reel Lift Cylinders
- 1.10.6. Bleeding the Reel Lift Cylinder System
- 1.10.7. Adjusting DialASpeed Reel Speed Ratio
- 1.10.8. Adjusting Reel Speed Ratio Sensor
- 1.10.9. Adjusting Reel Drive Gear
- 1.11. Lubrication
- 1.11.1. Lubricant Storage
- 1.11.2. Alternative and Synthetic Lubricants
- 1.11.3. Mixing of Lubricants
- 1.12. Lubrication and Maintenance
- 1.12.1. Lubrication Interval Chart
- 1.12.2. Care and Maintenance of Belts
- 1.12.3. Every 50 Hours of Operation
- 1.12.4. Every 200 400 Hours of Operation
- 1.12.5. Lubricate Knife Drive Gearbox Grease Fittings
- 1.13. Troubleshooting
- 1.13.1. Cutting Platform
- 1.13.2. Active Header Control
- 1.14. Service
- 1.14.1. Hydraulic Cylinder Safety Stop
- 1.14.2. Safe Cutting Platform Operation
- 1.14.3. Reel Safety Stops
- 1.14.4. Opening and Closing Right and LeftHand Shields
- 1.14.5. Remove and Install Knife Drive Belt
- 1.14.6. Adjusting Knife Drive Belt Tension
- 1.14.7. Replacing Cutterbar Knife
- 1.14.8. Knife and Knife Drive Alignment
- 1.14.9. Knife HoldDown Clearance
- 1.14.10. Replacing Knife Sections
- 1.14.11. Replacing Auger Fingers and Retainers
- 1.14.12. Stubble Light Bulb Replacement
- 1.14.13. Header Warning Light Bulb Replacement
- 1.15. Storage
- 1.15.1. End of Season Service
- 1.15.2. Beginning of Season Service
- 1.16. Specifications
- 1.16.1. Specifications
- 1.16.2. Dimensions/Weights
- 1.16.3. Keep Machines Secure
- 1.16.4. Header Identification Number
- 1.16.5. Keep Proof of Ownership
- 1.16.6. Unified Inch Bolt and Screw Torque Values
- 1.16.7. Metric Bolt and Screw Torque Values
- 1.17. John Deere Service Literature Available
- 1.17.1. Technical Information
- 1.18. John Deere Service Keeps You On The Job
- 1.18.1. John Deere Is At Your Service
- 2. Page Number
- 2.1. Section 05
- 2.2. Section 10
- 2.3. Section 15
- 2.4. Section 20
- 2.5. Section 25
- 2.6. Section 30
- 2.7. Section 35
- 2.8. Section 40
- 2.9. Section 45
- 2.10. Section 50
- 2.11. Section 55
- 2.12. Section 60
- 2.13. Section 65
- 2.14. Section 70
- 2.15. Section 75
- 2.16. Section 80
- 2.17. Section 85
