John Deere 600FD Series Flexible Draper Platform Operator Manual OMHXE90219
John Deere 600FD Series Flexible Draper Platform Operator Manual OMHXE90219-2
John Deere 600FD Series Flexible Draper Platform Operator Manual OMHXE90219-3
John Deere 600FD Series Flexible Draper Platform Operator Manual OMHXE90219-2
John Deere 600FD Series Flexible Draper Platform Operator Manual OMHXE90219-3

John Deere 600FD Series Flexible Draper Platform Operator Manual OMHXE90219

$30

  • Type Of Manual: Operator Manual
  • Manual ID: OMHXE90219
  • Format: PDF
  • Size: 6.5MB
  • Number of Pages: 150
Category: Tag:
Description
  • Model List:

    • 600FD Series Flexible Draper Platform
  • 1. Contents
  • 1.1. Safety Features
  • 1.1.1. Header Safety Features
  • 1.1.2. Recognize Safety Information
  • 1.1.3. Understand Signal Words
  • 1.1.4. Follow Safety Instructions
  • 1.1.5. Spanish Safety Signs and Operators Manual
  • 1.1.6. Ballasting for Safe Ground Contact
  • 1.1.7. Parking and Leaving the Machine
  • 1.1.8. Prepare for Emergencies
  • 1.1.9. Wear Protective Clothing
  • 1.1.10. Stay Clear of Harvesting Units
  • 1.1.11. Keep Hands Away From Knives
  • 1.1.12. Use Safety Lights and Devices
  • 1.1.13. Transport Combine With Header Safely
  • 1.1.14. Road Transport Disconnect Switch
  • 1.1.15. Practice Safe Maintenance
  • 1.1.16. Remove Paint Before Welding or Heating
  • 1.1.17. Avoid Heating Near Pressurized Fluid Lines
  • 1.1.18. Avoid Contact With Moving Parts
  • 1.1.19. Avoid Contact With Cutterbar
  • 1.1.20. Stay Clear of Rotating Drivelines
  • 1.1.21. Guards and Shields
  • 1.1.22. Avoid HighPressure Fluids
  • 1.1.23. Service Accumulator Systems Safely
  • 1.1.24. Service Machines Safely
  • 1.1.25. Service Drive Belts Safely
  • 1.1.26. Protect Against High Pressure Spray
  • 1.1.27. Dispose of Waste Properly
  • 1.1.28. Support Machine Properly
  • 1.1.29. Store Attachments Safely
  • 1.2. Safety Signs
  • 1.2.1. Front View Decals
  • 1.2.2. Rear View Decals
  • 1.2.3. Side View Decals
  • 1.2.4. Replace Safety Signs
  • 1.3. Transporting
  • 1.3.1. Transporting on Trailer
  • 1.3.2. Transport on Combine
  • 1.4. Attaching and Detaching
  • 1.4.1. Attaching Platform to Combine
  • 1.4.2. Position Warning Lights for Field Operation
  • 1.4.3. Detaching Platform from Combine
  • 1.4.4. Feeder House Manual Unlatching
  • 1.4.5. Replacement Shear Screw Location
  • 1.5. Calibration and Settings
  • 1.5.1. When to Calibrate
  • 1.5.2. Header Height Sensor Locations
  • 1.5.3. Calibration Error Codes
  • 1.5.4. SSeries Fault Codes
  • 1.5.5. Series Fault Codes
  • 1.5.6. User Calibration Procedures (S Series Combines)
  • 1.5.7. User Calibration Procedures (70 Series Combines)
  • 1.5.8. Adjusting Feeder House Drop Rate and Sensitivity S and 70 Series Combines
  • 1.5.9. Check Reel Fore/Aft Sensor (SSeries Combines S.N. 745101 )
  • 1.5.10. Check Reel Fore/Aft Sensor (70 Series Combines)
  • 1.5.11. Check Reel Height Sensor (SSeries Combines S.N. 745101 )
  • 1.5.12. Check Reel Height Sensor (70 Series Combines)
  • 1.5.13. Check Header Height Sensors (SSeries Combines S.N. 745101 )
  • 1.5.14. Check Header Height Sensors (70 Series Combines)
  • 1.5.15. Adjust Header Height Sensors
  • 1.6. Operating the Platform
  • 1.6.1. General Information
  • 1.6.2. Setting Backshaft Speed
  • 1.6.3. Armrest Functions
  • 1.6.4. Active Header Control DisplayFeatures
  • 1.6.5. Description of Automatic Header Height Control Systems
  • 1.6.6. Draper Belt Speed
  • 1.6.7. Draper Belt Speed Adjust Switch
  • 1.6.8. Side Belt Speed Reduction Switch
  • 1.6.9. Draper Belt Protection System
  • 1.6.10. Automatic Header Height Control HydraFlex Mode
  • 1.6.11. Automatic Header Height ControlRigid Mode
  • 1.6.12. Operate HydraFlex Pressure
  • 1.6.13. Reel Settings
  • 1.6.14. Reel Resume
  • 1.6.15. Reel Reverse (S and 70 Series Combines Only)
  • 1.7. Attachments and Options
  • 1.7.1. Attachments and Options
  • 1.8. Adjustments Leveling Platform
  • 1.8.1. Leveling Platform to Ground
  • 1.9. Adjustments Feeding Related
  • 1.9.1. Side Draper Belt Tension
  • 1.9.2. Center Draper Belt Tension
  • 1.9.3. Center Sump Cover Adjustment
  • 1.9.4. Knife HoldDown Clearance
  • 1.9.5. Feed Drum Stripper Clearance
  • 1.10. Adjustments PermaGlide Divider Points
  • 1.10.1. Height Adjustment of PermaGlide Divider Point
  • 1.11. Adjustments Reel
  • 1.11.1. Set Reel Safety Stops
  • 1.11.2. Minimum Reel Height and Leveling Reel
  • 1.11.3. Fore/Aft Cylinder Mount Adjustment
  • 1.11.4. Rephasing Reel Fore/Aft Cylinders
  • 1.11.5. Rephasing Reel Lift Cylinders
  • 1.11.6. Bleeding Reel Lift Cylinder System
  • 1.11.7. Adjust Reel Fingers
  • 1.11.8. DialASpeed Reel
  • 1.11.9. Reel Speed Ratio Sensor Adjustment
  • 1.11.10. Reel Drive Gear Adjustment
  • 1.12. Lubrication
  • 1.12.1. Lubricant Storage
  • 1.12.2. Alternative and Synthetic Lubricants
  • 1.12.3. Mixing of Lubricants
  • 1.13. Lubrication and Maintenance
  • 1.13.1. Lubrication and Maintenance Interval Chart
  • 1.13.2. Daily Routine Machine Inspection
  • 1.13.3. Every 10 Hours of Operation
  • 1.13.4. Every 50 Hours of Operation
  • 1.13.5. Every 200 and 400 Hours of Operation
  • 1.14. Troubleshooting
  • 1.14.1. Cutting Platform
  • 1.14.2. Active Header Height Control
  • 1.15. Service
  • 1.15.1. Feeder House Safety Stop
  • 1.15.2. Reel Safety Stops
  • 1.15.3. Open Side Shields
  • 1.15.4. Remove and Install Telescoping Knife Drive Shaft
  • 1.15.5. Set Cutterbar Knife Timing
  • 1.15.6. Cutterbar Maintenance
  • 1.15.7. Knife Section Service Kit
  • 1.15.8. Remove and Install Cutterbar Knife
  • 1.15.9. Remove and Install Knife Sections
  • 1.15.10. Align Knife Head and Knife Drive
  • 1.15.11. Spare Knife Storage
  • 1.15.12. Remove and Install Knife Guards
  • 1.15.13. Center Draper Cleanout
  • 1.15.14. Cleaning Material Build Up at Side Shields
  • 1.15.15. Clean Material Build Up at Center Belt Drive Shaft
  • 1.15.16. Remove and Install Side Draper Belts 630FD
  • 1.15.17. Remove and Install Side Draper Belts 635FD, 640FD, and 645FD
  • 1.15.18. Remove and Install Center Draper Belt
  • 1.15.19. Remove and Install Feed Drum Finger Guides
  • 1.15.20. Remove and Install Feed Drum Fingers
  • 1.15.21. Header Warning Light Bulb Replacement
  • 1.15.22. Stubble Light Bulb Replacement
  • 1.16. Storage
  • 1.16.1. End of Season Service
  • 1.16.2. Beginning of Season Service
  • 1.17. Specifications
  • 1.17.1. Overall Dimensions
  • 1.17.2. Component Specifications
  • 1.17.3. Platform Weights
  • 1.17.4. Keep Machines Secure
  • 1.17.5. Header Identification Number
  • 1.17.6. Keep Proof of Ownership
  • 1.17.7. Unified Inch Bolt and Screw Torque Values
  • 1.17.8. Metric Bolt and Screw Torque Values
  • 1.18. John Deere Service Literature Available
  • 1.18.1. Technical Information
  • 1.19. John Deere Service Keeps You On The Job
  • 1.19.1. John Deere Is At Your Service
  • 2. Page Number
  • 2.1. Section 05
  • 2.2. Section 10
  • 2.3. Section 15
  • 2.4. Section 20
  • 2.5. Section 25
  • 2.6. Section 30
  • 2.7. Section 35
  • 2.8. Section 40
  • 2.9. Section 45
  • 2.10. Section 50
  • 2.11. Section 55
  • 2.12. Section 60
  • 2.13. Section 65
  • 2.14. Section 70
  • 2.15. Section 75
  • 2.16. Section 80
  • 2.17. Section 85
  • 2.18. Section 90

Related products

-50%
Mahindra Tractor 15 Series 2015 4WD Full Operator Manual Fast Download

Mahindra

Mahindra Tractor 15 Series 2015 4WD Operator Manual

Original price was: $20.Current price is: $10.
Add to cart
-50%
Mahindra Tractor 00 Series 4500 5500 6000 6500 Full Operator Manual Fast Download

Mahindra

Mahindra Tractor 0 Series 2WD 4500 5500 6000 6500 Operator Manual

Original price was: $20.Current price is: $10.
Add to cart
Mahindra Tractor 16 Series 3016 Gear HST Full Parts Manual Fast Download

Mahindra

Mahindra Tractor 16 Series 3016 Gear HST Parts Manual

$20
Add to cart
Mahindra Tractor 16 Series 1816 HST Full Parts Manual Fast Download

Mahindra

Mahindra Tractor 16 Series 1816 HST Parts Manual

$20
Add to cart
Mahindra Tractor 10 Series 4010 HST Full Parts Manual Fast Download

Mahindra

Mahindra Tractor 10 Series 4010 HST Parts Manual

$20
Add to cart
-50%
Mahindra Tractor 10 Series 6110 Gear Cab Full Operator Manual Fast Download

Mahindra

Mahindra Tractor 10 Series 6110 Gear Cab Operator Manual

Original price was: $20.Current price is: $10.
Add to cart
Mahindra Tractor 16 Series 3616 Gear HST Full Parts Manual Fast Download

Mahindra

Mahindra Tractor 16 Series 3616 Gear HST Parts Manual

$20
Add to cart
-50%
Mahindra Tractor 30 Series 4WD 4530 Full Operator Manual Fast Download

Mahindra

Mahindra Tractor 30 Series 4WD 4530 Operator Manual

Original price was: $20.Current price is: $10.
Add to cart