John Deere HX10 and HX14 Rotary Cutter Operator Manual OMP73906
$30
- Type Of Manual: Operator Manual
- Manual ID: OMP73906
- Format: PDF
- Size: 7.0MB
- Number of Pages: 82
Description
-
Model List:
- HX10 Rotary Cutter
- HX14 Rotary Cutter
- 1. Contents
- 1.0.1. Recognize Safety Information
- 1.0.2. Understand Signal Words
- 1.0.3. Follow Safety Instructions
- 1.0.4. Protect Bystanders
- 1.0.5. Stay Clear of Rotating Blades
- 1.0.6. Operate Tractor and Cutter Safely
- 1.0.7. Back Up Safely
- 1.0.8. Leaving Cutter Unattended
- 1.0.9. Keep Riders Off Machine
- 1.0.10. Prepare for Emergencies
- 1.0.11. Wear Protective Clothing
- 1.0.12. Stay Clear of Rotating Drivelines
- 1.0.13. Use Safety Lights and Devices
- 1.0.14. Tow Loads Safely
- 1.0.15. Observe Maximum Transport Speed
- 1.0.16. Tire Maximum Transport Speeds
- 1.0.17. Transport Safely
- 1.0.18. Use a Safety Chain
- 1.0.19. Avoid Serious Injury or Death from Accidental Lowering of Cutter
- 1.0.20. Practice Safe Maintenance
- 1.0.21. Remove Paint Before Welding or Heating
- 1.0.22. Avoid Heating Near Pressurized Fluid Lines
- 1.0.23. Check Hoses for Damage
- 1.0.24. Avoid HighPressure Fluids
- 1.0.25. Store Attachments Safely
- 1.0.26. Safety Features
- 1.1. Safety Signs
- 1.1.1. Replace Safety Signs
- 1.1.2. Safety SignsDrivelines
- 1.1.3. Safety SignsDriveline Shields
- 1.1.4. Safety SignsHitch
- 1.1.5. Safety SignsDeck
- 1.2. Preparing the Tractor
- 1.2.1. Selecting Tractor PTO Speed
- 1.2.2. Positioning Tractor DrawbarPullType
- 1.2.3. Tractor Drawbar Static Vertical Loads (PullType)
- 1.2.4. Positioning Tractor DrawbarLiftType
- 1.2.5. Adjusting Tractor HitchPullType
- 1.2.6. Adjusting Tractor HitchLiftType
- 1.2.7. Recommended Tractor Hydraulic Outlets (PullType)
- 1.2.8. Checking Ballast, Wheel Spacing, and Tire Inflation
- 1.2.9. Determining Front Ballast (LiftType)
- 1.3. Preparing the Cutter
- 1.3.1. Prestarting Checklist
- 1.3.2. Positioning Hitch Pins (LiftType)
- 1.3.3. Checking Tailwheel Support VBolt Torque
- 1.3.4. Adjusting Tailwheel Spacing
- 1.4. Attaching and Detaching
- 1.4.1. Attach LiftType Cutter to Tractor with Quick Coupler Hitch
- 1.4.2. Attach LiftType Cutter to Tractor with ThreePoint Hitch
- 1.4.3. Adjusting Hitch Clevis (PullType)
- 1.4.4. Attaching PullType Cutter to Tractor Drawbar
- 1.4.5. Assembling Main PTO Driveline Telescoping Members (If Necessary)
- 1.4.6. Attaching PTO Driveline
- 1.4.7. Attaching to Tractor Hydraulic System (PullType)
- 1.4.8. Connecting Tail/Warning Light Wiring Harness to Tractor (If Equi
- 1.4.9. Detach Cutter From Tractor
- 1.5. Transporting
- 1.5.1. Preparing Cutter For Transport
- 1.5.2. Follow Safe Transport Procedures
- 1.5.3. Lighting Enhancement Module Operation (If Equipped)
- 1.5.4. Driving Cutter In Turns
- 1.5.5. Keep Riders Off Machine
- 1.6. Operating the Cutter
- 1.6.1. Preparing Cutter for OperationLiftType
- 1.6.2. Preparing Cutter for OperationPullType
- 1.6.3. Adjusting Cutting HeightLiftType
- 1.6.4. Adjusting Cutting HeightPullType
- 1.6.5. Keep Riders Off Machine
- 1.6.6. Follow Safe Operating Procedures
- 1.6.7. Operating the Cutter for Best Performance
- 1.6.8. Turning CutterLiftType
- 1.6.9. Turning CutterPullType
- 1.6.10. Attachments Available
- 1.7. Lubrication and Maintenance
- 1.7.1. Lubricating and Maintaining Machine Safely
- 1.7.2. Gear Case Oil
- 1.7.3. Alternative and Synthetic Lubricants
- 1.7.4. Mixing of Lubricants
- 1.7.5. Lubricant Storage
- 1.7.6. Perform Lubrication and Maintenance
- 1.7.7. Observe Lubrication Symbols
- 1.7.8. Every 10 Hours or Daily
- 1.7.9. Every 24 Hours
- 1.7.10. Every 50 Hours
- 1.7.11. As Required
- 1.8. Service
- 1.8.1. Practice Safe Service Procedures
- 1.8.2. Keep Service Area Clean
- 1.8.3. Avoid HighPressure Fluids
- 1.8.4. Service Tires Safely
- 1.8.5. Service Severe Duty Ag Tires Safely
- 1.8.6. Using Slip Clutch Storage Feature
- 1.8.7. Disassembling and Inspecting Slip Clutch
- 1.8.8. Assembling Slip Clutch
- 1.8.9. Removing and Installing PTO DrivelineLiftType
- 1.8.10. Removing and Installing PTO DrivelinesPullType
- 1.8.11. Checking Blade Wear
- 1.8.12. Replacing BladesRound Pan Holder
- 1.8.13. Replacing BladesBar Type Holder (HX14)
- 1.8.14. Direction of Blade Rotation
- 1.8.15. Replacing Cross Shaft Shear Bolt (HX14)
- 1.8.16. Timing Blade HoldersHX10
- 1.8.17. Timing Blade HoldersHX14 (1000 RPM Machine)
- 1.8.18. Replacing Skid Shoes
- 1.8.19. Metric Bolt and Screw Torque Values
- 1.8.20. Unified Inch Bolt and Screw Torque Values
- 1.9. John Deere Service Keeps You On The Job
- 1.9.1. John Deere Is At Your Service
- 2. Page Number
- 2.1. Section 05
- 2.2. Section 10
- 2.3. Section 15
- 2.4. Section 20
- 2.5. Section 25
- 2.6. Section 30
- 2.7. Section 35
- 2.8. Section 40
- 2.9. Section 45
Related products
-50%
Original price was: $20.$10Current price is: $10.
-50%
Original price was: $20.$10Current price is: $10.
-50%
Original price was: $20.$10Current price is: $10.
-50%
Original price was: $20.$10Current price is: $10.
-50%
Original price was: $20.$10Current price is: $10.
-50%
Original price was: $20.$10Current price is: $10.
