Manitou 200 ATJE S1 Operator Manual 647800EN-USM1A62020

Manitou 200 ATJE S1 Operator Manual 647800EN-USM1A62020 - Image 2

Manitou 200 ATJE S1 Operator Manual 647800EN-USM1A62020 - Image 3

Manitou 200 ATJE S1 Operator Manual 647800EN-USM1A62020 - Image 4

Manitou 200 ATJE S1 Operator Manual 647800EN-USM1A62020 - Image 5

manitou 200 atje s1 operator manual 647800en usm1a62020 2

manitou 200 atje s1 operator manual 647800en usm1a62020 3

Manitou 200 ATJE S1 Operator Manual 647800EN-USM1A62020

Type Of Manual: Operator Manual
Manual ID: 647800EN-USM1A62020
Format: PDF
Size: 6.6MB
Number of Pages: 152

Category: Manitou Operator Manual PDF

Description

Model List:
- 200 ATJE S1

1. OPERATING AND SAFETY INSTRUCTIONS
1.1. INSTRUCTIONS TO THE COMPANY MANAGER
1.1.1. THE SITE
1.1.2. THE OPERATOR
1.1.3. THE MACHINE
1.1.3.1. A SUITABILITY OF THE MACHINE FOR THE TASK
1.1.3.2. B ADAPTING THE MACHINE TO USUAL ENVIRONMENTAL CONDITIONS
1.1.3.3. C MODIFYING THE MACHINE
1.1.4. INSTRUCTIONS
1.1.5. MAINTENANCE
1.2. INSTRUCTIONS FOR THE OPERATOR
1.2.1. INTRODUCTION
1.2.2. GENERAL INSTRUCTIONS
1.2.2.1. A OPERATORS MANUAL
1.2.2.2. B AUTHORISATION FOR USE IN FRANCE
1.2.2.3. C MAINTENANCE
1.2.2.4. D MODIFYING THE MACHINE
1.2.2.5. E GROUND LINK
1.2.2.6. F SAFETY DEVICES
1.2.3. OPERATING INSTRUCTIONS
1.2.3.1. A BEFORE USING THE MACHINE
1.2.3.2. B DRIVERS CAB LAYOUT
1.2.3.3. C ENVIRONMENT
1.2.3.4. D VISIBILITY
1.2.3.5. E STARTING MACHINES WITH A DIESEL ENGINE
1.2.3.6. F SWITCHING ON ELECTRICAL MACHINES
1.2.3.7. G DRIVING THE MACHINE
1.2.3.8. H SHUTTING DOWN THE MACHINE
1.2.4. INSTRUCTIONS FOR WELDING AND BLOW TORCH WORK ON AN EXTERNAL STRUCTURE
1.2.4.1. A WITH AN ELECTRICAL WELDING SET
1.2.4.2. B WITH A BLOW TORCH
1.3. MACHINE MAINTENANCE INSTRUCTIONS
1.3.1. GENERAL INSTRUCTIONS
1.3.2. MAINTENANCE
1.3.2.1. MAINTENANCE LOGBOOK
1.3.3. LUBRICANT AND FUEL LEVELS
1.3.4. HYDRAULICS
1.3.5. ELECTRICITY
1.3.6. TILT SENSOR
1.3.7. WELDING ON THE MACHINE
1.3.8. WASHING THE MACHINE
1.4. IF THE MACHINE IS NOT TO BE USED FOR A LONG TIME
1.4.1. INTRODUCTION
1.4.2. PREPARATION OF THE MACHINE
1.4.3. MACHINES WITH A DIESEL ENGINE ENGINE PROTECTION
1.4.4. ELECTRICAL MACHINES BATTERY CHARGE
1.4.5. PROTECTING THE MACHINE
1.4.6. BRINGING THE MACHINE BACK INTO SERVICE
1.5. DISPOSING OF THE MACHINE
1.5.1. RECYCLING OF MATERIALS
1.5.1.1. METALS
1.5.1.2. PLASTICS
1.5.1.3. RUBBER
1.5.1.4. GLASS
1.5.2. ENVIRONMENTAL PROTECTION
1.5.2.1. WORN OR DAMAGED PARTS
1.5.2.2. USED OIL
1.5.2.3. USED BATTERIES
2. DESCRIPTION
2.1. CE DECLARATION OF CONFORMITY
2.2. COMPONENT LOCATIONS
2.3. STICKERS
2.4. SPECIFICATIONS
2.5. DIMENSIONS AND MOVEMENT AMPLITUDE
2.6. SAFETY COMPONENTS
2.6.1. SLIDING MIDRAIL
2.6.2. SLIDING MIDRAIL AND GATE
2.6.3. SAFETY HARNESS ATTACHMENT POINTS
2.6.4. HANDRAILS
2.6.5. TURNTABLE LOCKING PIN
2.7. CONTROL PANEL AND SAFETY DEVICES AT GROUND LEVEL
2.8. CONTROL PANEL AND SAFETY DEVICES IN THE PLATFORM
2.9. GROUND LEVEL SCREEN
2.9.1. POWERUP CYCLE
2.9.2. DISPLAY ZONES
2.9.3. WORK PAGE
2.9.4. BATTERY CHARGER PAGE
2.9.5. WARNING PAGE AND FAULT PAGE
2.10. PLATFORM SCREEN
2.10.1. POWERUP CYCLE
2.10.2. DISPLAY ZONES
2.10.3. WORK PAGE
2.10.4. WARNING PAGE AND FAULT PAGE
2.11. OPERATING THE MACHINE
2.11.1. TRANSPORT/WORKING POSITION
2.11.1.1. TRANSPORT POSITION
2.11.1.2. WORKING POSITION
2.11.2. OPERATION FROM THE GROUND LEVEL CONTROL PANEL
2.11.2.1. TURNING THE MACHINE ON
2.11.2.2. TURNING THE MACHINE OFF
2.11.2.3. POSITIONING THE PLATFORM
2.11.2.4. ACTIVATING SIMULTANEOUS FUNCTIONS
2.11.2.5. EMERGENCY STOP
2.11.3. USE FROM THE CONTROL PANEL IN THE PLATFORM
2.11.3.1. TURNING THE MACHINE ON/OFF
2.11.3.2. DRIVING, STEERING AND BRAKING THE MACHINE
2.11.3.3. POSITIONING THE PLATFORM
2.11.3.4. ACTIVATING SIMULTANEOUS FUNCTIONS
2.11.3.5. EMERGENCY STOP
2.11.4. FUNCTIONS LOCKED
2.11.4.1. MACHINE IN TRANSPORT POSITION
2.11.4.2. MACHINE IN WORKING POSITION
2.12. CHARGING THE BATTERIES
2.13. EMERGENCY CONTROLS
2.13.1. SHOULD THE USER FEEL ILL PRIORITY CONTROLS FROM THE GROUND
2.13.2. IF THERE IS A BREAKDOWN EMERGENCY CONTROLS FROM THE PLATFORM
2.13.3. IF THERE IS A BREAKDOWN EMERGENCY CONTROLS FROM THE GROUND
2.14. STANDARD EQUIPMENT
2.14.1. BATTERY CUTOFF
2.14.2. OSCILLATING FRONT AXLE
2.15. OPTIONS
2.15.1. KEY LOCK FOR TURNTABLE COVERS
2.15.2. V ELECTRIC POWER SOCKET IN THE PLATFORM
2.15.3. HYDRAULIC OIL HEATER
2.15.4. WORKLIGHT IN THE PLATFORM
2.15.5. SECONDARY PROTECTION SYSTEM SPS
2.16. TRANSPORT AND LIFTING
2.16.1. TRANSPORT INSTRUCTIONS
2.16.1.1. LOADING/UNLOADING THE MACHINE
2.16.1.2. CONFIGURING THE MACHINE FOR TRANSPORT
2.16.1.3. SECURING THE MACHINE
2.16.2. FREEWHEEL FOR TOWING/WINCHING
2.16.3. LIFTING INSTRUCTIONS
3. MAINTENANCE
3.1. INTRODUCTION
3.2. ORIGINAL MANITOU SPARE PARTS AND EQUIPMENT
3.3. DAILY AND MONTHLY MAINTENANCE
3.4. COMPULSORY SERVICES AND PERIODIC MAINTENANCE
3.5. OCCASIONAL MAINTENANCE AND OCCASIONAL OPERATIONS
3.6. FILTERS AND CARTRIDGES
3.7. LUBRICANTS
3.8. Ü DAILY MAINTENANCE
3.9. Ü MONTHLY MAINTENANCE OR EVERY 50HOURS OF SERVICE
3.10. Ü 250H PERIODIC MAINTENANCE EVERY 250 HOURS OF SERVICE OR 6 MONTHS
3.11. Ü 500H PERIODIC MAINTENANCE EVERY 500HOURS OF SERVICE OR 1 YEAR
3.12. Ü 1000H PERIODIC SERVICE EVERY 1,000 HOURS OF SERVICE OR 2 YEARS
3.13. Ü 1500H PERIODIC SERVICE EVERY 1,500 HOURS OF SERVICE OR 3 YEARS
3.14. Ü 2000H PERIODIC SERVICE EVERY 2,000 HOURS OF SERVICE OR 4 YEARS
3.15. Ü OPTIONAL PERIODIC MAINTENANCE
3.16. Ü OCCASIONAL SERVICING
3.17. Ü OCCASIONAL OPERATIONS

Manitou 200 ATJE S1 Operator Manual 647800EN-USM1A62020

Description

Related products

Login