Description
-
Model List:
- MI 50 L D D ST5 S1
- MI 60 D D ST5 S1
- MI 70 D D ST5 S1
- 1. Legal disclaimer
- 2. Foreword
- 3. Intervention during the warranty period
- 4. Supplier Documentation List
- 5. Safety
- 5.1. Servicing position
- 5.2. Servicing Rules
- 6. Reference Information
- 6.1. Explanation of symbols
- 6.2. Metric imperial unit conversion
- 6.3. List of Abbreviations
- 6.4. Standard tightening torques
- 7. Caracteristics and specifications
- 7.1. Technical datasheet MI 60 D D ST5 S1
- 7.2. Technical datasheet MI 50 L D D ST5 S1
- 7.3. Technical datasheet MI 70 D D ST5 S1
- 8. Characteristics and Specifications
- 8.1. Power Disposition
- 8.2. Air intake system
- 8.3. Cooling System
- 9. Schematics
- 9.1. Fuel circuit
- 9.2. Lubrication circuit
- 10. Location
- 10.1. Engine mounting
- 10.2. Fuel injection circuit
- 10.3. Power system
- 10.4. Exhaust System
- 11. Control and Adjustment
- 11.1. Management of engine regeneration from display screen
- 12. Removal
- 12.1. Removal of The Air Filter
- 12.2. Removal Of The Fap
- 12.3. Removal Of The Radiator
- 12.4. Removal Of The Gearbox Engine Assembly
- 13. Troubleshooting
- 13.1. Management of engine fault codes from display screen
- 13.2. Engine troubleshooting procedure
- 14. Specific Tools
- 14.1. Electronic belt tensiometer
- 15. Calibration of the transmission from the display screen
- 16. Hydrodynamic transmission gearbox
- 16.1. Characteristics and specifications
- 16.2. Operating principle
- 16.3. Structural presentation
- 16.4. Removal
- 16.5. Installation
- 16.6. Troubleshooting
- 17. Transmission shaft
- 17.1. Characteristics and Specifications
- 17.2. Removal
- 18. Characteristics and Specifications
- 18.1. Steering System
- 18.2. Steering Axle
- 18.3. Drive Axle
- 19. Control and Adjustment
- 19.1. Steering Axle
- 19.2. Drive Axle
- 20. Removal
- 20.1. Dismantle and Assemble
- 20.2. Dismantle and Assemble of Hub Reduction Gear
- 20.3. Main Reducing Gear Dismantle and Assemble
- 20.4. Drive Spiral Bevel Gear
- 20.5. Dismantle Differential Carrier
- 21. Refit
- 21.1. Assemble Drive Spiral Bevel Gear
- 21.2. Install Differential Carrier
- 21.3. Assemble Reducer Housing
- 22. Troubleshooting
- 22.1. Fault Diagnosis And Corrections
- 23. Characteristics and Specifications
- 23.1. Brake System
- 23.2. Data
- 23.3. Brake Valve
- 24. Control and Adjustment
- 24.1. Pedal Height, Free Stroke
- 24.2. Accumulator
- 24.3. Inch pedal calibration
- 24.4. Hand Brake
- 24.5. Service Brake
- 25. Troubleshooting
- 25.1. Main Brake
- 25.2. Hand Brake
- 26. Characteristics and Specifications
- 26.1. Lifting System
- 26.2. Assemble Debugging Data
- 26.3. Duplex Wide View Mast
- 26.4. Duplex Full Free Lift Mast
- 26.5. Triple Full Free Lift Mast
- 27. Control and Adjustment
- 27.1. Left And Right Cylinder Height Adjustment
- 27.2. Clearance of Fork Carriage And Rollers Adjustment
- 27.3. Lifting Chain Adjustment
- 27.4. Tightening torques for mast MI BT ST5
- 28. Removal
- 28.1. Mast Dismantle and Install Adjustment
- 28.2. Disassembly and Installation of Tilting Cylinder
- 28.3. Assemble And Replace QuickWear Part
- 28.4. Disassembly and Installation of Lifting Cylinder
- 28.5. Installing And Dismantling Way Of Load Backrest Extension
- 29. Troubleshooting
- 29.1. Fault Diagnosis And Corrections
- 30. Characteristics and Specifications
- 30.1. Oil Pump
- 30.2. Performance Parameter
- 30.3. Hydraulic Steering Gear
- 30.4. Multiple Directional Control Valve
- 30.5. Rotary Type Piping Filter
- 30.6. Tilting Cylinder
- 30.7. Lifting Cylinder
- 30.8. OneWay Governor Valve
- 31. Schematics
- 31.1. MI 50L70 ST5 Hydraulic Schematic
- 31.2. MI 80100 ST5 Hydraulic Schematic
- 32. Control and Adjustment
- 32.1. Performance Parameter
- 32.2. Main Relief Valve Pressure Adjustment
- 32.3. Air Exhaust In Hydraulic System
- 33. Troubleshooting
- 33.1. Common Fault and Corrections
- 33.2. Fault Diagnosis And Adjustment
- 33.3. Hydraulic System Fault Diagnosis and Corrections
- 34. Specific Tools
- 34.1. Digital manometer kit
- 34.2. Basic manometer kit
- 35. Characteristics and Specifications
- 35.1. Electrical System
- 35.2. ECU pin assignment MI 5070
- 35.3. ECU pin assignment MI 80100
- 35.4. Electrical Plate Assembly
- 35.5. Key Switch(start)
- 35.6. Combination Switch Assembly
- 35.7. Light Combination Switch
- 36. Schematics
- 36.1. Position per diagram MI 50L70D D ST5 S1
- 36.2. MI 50L70D D ST5 S1 Electrical Schematic
- 37. Location
- 37.1. Electrical components
- 38. Control and Adjustment
- 38.1. Managing engine regeneration from the display screen
- 38.2. Managing engine fault codes from the display screen
- 38.3. Calibrating transmission inch pedal from display screen
- 39. Troubleshooting
- 39.1. Starter And Generator Repair
- 40. Specific Tools
- 40.1. Breakout boxes
- 41. Removal
- 41.1. Removal Of The Cabin
- 41.2. Disassembly And Installation
- 42. Removal
- 42.1. Removal Of The Counterweight
- 43. Optional mini levers
- 43.1. Characteristics and Specifications
- 43.2. Hydraulics
- 43.3. Electrical diagram
- 43.4. Location
- 43.5. Control and adjustments
- 43.6. Troubleshooting
- 44. Diagnostics case
- 44.1. Diagnostics case
- 44.2. Example of connection to the machine
- 44.3. Accessories
- 45. Diagnostics component
- 45.1. Component diagnostics box
- 45.2. Example of connection to the component
- 46. SMARTASSISTDirect diagnostic tool
- 46.1. SMARTASSISTDirect
- 47. Electronic belt tensiometer
- 47.1. Electronic belt tensiometer
- 48. Fault codes
- 48.1. Management of engine fault codes from display screen
- 48.2. DTC Motor Deutz ST5
- 48.3. WG 94 Gearbox fault codes
- 49. Page vierge
