-
Model List:
- TCD 3.6 L4 ST3B Engine. TD 3.6 L4 ST3B Engine
- 1. Workshop Manual
- 2. Table of contents
- 2.1. Foreword
- 2.2. General
- 2.3. Safety information / User information
- 2.4. Job card overview
- 2.5. Sorted alphabetically
- 2.6. Sorted numerically
- 2.7. Job cards
- 3. Renewing the crankshaft sealing ring (flywheel side)
- 4. Removing and installing the gasket housing
- 5. Removing and installing the transfer line
- 6. Closing parts
- 7. Oil measuring device
- 8. Line
- 9. Removing and installing the lubricating oil pan
- 10. Closing parts
- 11. Drain valve
- 12. Oil filling
- 13. Removing and installing the Vbelt pulley / Vribbed pulley
- 14. Removing and installing the flywheel (Fastening parts)
- 15. Removing and installing the sensor wheel
- 16. Vbelt pulley
- 17. Removing and installing the cylinder head cover
- 18. Renewing the crankshaft sealing ring (opposite side to flywheel)
- 19. Control valve
- 20. Removing and installing the lubricating oil cooler
- 21. Lubricant oil filter console
- 22. Removing and installing the oil suction pipe
- 23. Removing and installing the lubricating oil line (exhaust turbocharger)
- 24. Removing and installing the lubricating oil return line (exhaust turbocharger)
- 25. Lubricating oil line
- 26. Removing and installing the highpressure pump
- 27. Removing and installing the injector
- 28. Fastening parts
- 29. Fuel prefilter
- 30. Fuel filter
- 31. Fuel line
- 32. Supply pump (Fuel)
- 33. Removing and installing the rail
- 34. Removing and installing the fuel line (injector, rail, highpressure pump)
- 35. Removing and install the charge air line
- 36. Removing and installing charge air manifold
- 37. Pressure transmitter / temperature pressure transmitter (charge air)
- 38. Intake nozzle (exhaust turbocharger)
- 39. Charge air manifold
- 40. Charge air line
- 41. Removing and installing the coolant pump
- 42. Drive components
- 43. Vrib belt pulley
- 44. Removing and installing the thermostat
- 45. Checking the thermostat (in the removed state)
- 46. Line
- 47. Line (Thermostat housing, lubricating oil cooler, coolant line)
- 48. Pressure fan
- 49. Removing and installing the exhaust line
- 50. Removing and installing the flutter valve
- 51. Removing and installing the cooler
- 52. Removing and installing the exhaust gas return valve
- 53. Connection (Crankcase housing, exhaust gas circulation, coolant line)
- 54. Screw plug (Thermostat housing, exhaust gas circulation, coolant line)
- 55. Holder
- 56. Holder
- 57. Compensator structure (Exhaust line)
- 58. Line (Crankcase housing, exhaust gas circulation, coolant line)
- 59. Line (Thermostat housing, exhaust gas circulation, coolant line)
- 60. Removing and installing the turbocharger
- 61. Exhaust manifold (exhaust turbocharger)
- 62. Removing and installing the belt tensioner (Vrib belt, level 1)
- 63. Removing and installing the generator (Clamping latch)
- 64. Removing and installing the generator (Fastening parts)
- 65. Removing and installing the console (Vrib belt, level 1)
- 66. Removing and installing the starter
- 67. Generator
- 68. Engine mounting
- 69. Engine mounting
- 70. Engine mounting
- 71. Engine mounting
- 72. Removing and installing the pressure/temperature sensor (charge air)
- 73. Fastening parts
- 74. Holder (Relay)
- 75. Removing and installing turning gear / locking device
- 76. Impulse transmitter (crankshaft)
- 77. Impulse transmitter (camshaft)
- 78. Pressure transmitter installation (oil pressure)
- 79. Removing and installing the connection housing
- 80. Removing and installing the connection housing
- 81. Connection housing
- 82. Removing and installing the glow plugs
- 83. Holder
- 84. Compensator structure (assembly material)
- 85. Inlet module
- 86. Outlet module
- 87. Console
- 88. Removing and installing the coolant compressor
- 89. Fastening parts
- 90. Removing and installing hydraulic pump drive
- 91. Vent the fuel system
- 92. Special tools








