John Deere 2730 Combination Ripper Operator Manual OMKK60471

John Deere 2730 Combination Ripper Operator Manual OMKK60471-2

John Deere 2730 Combination Ripper Operator Manual OMKK60471-3

John Deere 2730 Combination Ripper Operator Manual OMKK60471

Type Of Manual: Operator Manual
Manual ID: OMKK60471
Format: PDF
Size: 5.7MB
Number of Pages: 128

Category: John Deere Operators Manuals PDF Tag: Agricultural

Description

Model List:
- 2730 Combination Ripper

1. Introduction
1.1. Foreword
1.2. A Message to Our Customers
1.3. Recognize Safety Information
1.4. Understand Signal Words
1.5. Follow Safety Instructions
1.6. Prepare for Emergencies
1.7. Wear Protective Clothing
1.8. Protect Against Noise
1.9. Practice Safe Maintenance
1.10. Handle Electronic Components and Brackets Safely
1.11. Park Machine Safely
1.12. Support Raised Equipment
1.13. Remove Paint Before Welding or Heating
1.14. Avoid Heating Near Pressurized Fluid Lines
1.15. Avoid HighPressure Fluids
1.16. Inspect Lift Circuit Hoses
1.17. Store Attachments Safely
1.18. Service Tires Safely
1.19. Decommissioning Proper Recycling and Disposal of Fluids and Components
1.20. Handle Chemical Products Safely
1.21. Operate Safely
1.22. NonPermissible Use
1.23. Use Safety Lights and Devices
1.24. Keep Riders Off Machine
1.25. Observe Maximum Transport Speed
1.26. Use a Signal Person
1.27. Use a Safety Chain
1.28. Tow Loads Safely
1.29. Avoid Overhead Power Lines
1.30. Prepare for Transport
1.31. Transport Safely
1.32. Transport Implement Train
1.33. Transport LockUp Valve
1.34. Do Not Fold Wings Until Machine Is Fully Raised
1.35. Park Safely
2. Safety Signs
2.1. Replace Safety Signs
2.2. Main Frame
2.3. WingsFolding Machines
2.4. Informational Decals
3. Safety Features
3.1. Safety FeaturesMachines With SAE Connector
3.2. Safety FeaturesMachines With ISO Connector
4. Preparing Tractor
4.1. Determine Tractor Requirements
4.2. Drawbar Requirements
4.3. Prepare Hydraulic SystemJohn Deere 8000/9000 and R/RT Series Tractors
4.4. Secure ThreePoint Hitch
4.5. Position Drawbar
5. Preparing Machine
5.1. Check and Lubricate Machine
5.2. Tighten Hardware
5.3. Machine Preparation Checklist
5.4. Adjust FronttoRear Leveling
5.5. Level Wing Frames to Main FrameFolding Machines
5.6. Adjust Scraper for SelfAdjusting Operation
5.7. Adjust Scraper for Rigid Operation
6. Attaching and Detaching
6.1. Use Your Tractor and Tillage Equipment Operators Manuals
6.2. Make Proper Hose Connections
6.3. Before Attaching Machine to Tractor
6.4. Attach Machine to Tractor
6.5. Attach Warning Light Plug
6.6. Use Warning Lights and SMV Emblem
6.7. Position Jack Stand for Transport
6.8. Attach Safety Chain to Tractor
6.9. Engage Transport LockUp Valve
6.10. Check Wing Fold OperationFolding Machines
6.11. Check Depth Control Operation
6.12. Detach From Tractor
7. Transporting
7.1. Use Safety Lights and Devices
7.2. Observe Maximum Transport Speed
7.3. Use a Safety Chain
7.4. Attach Safety Chain to Tractor
7.5. Tow Loads Safely
7.6. Avoid Overhead Power Lines
7.7. Prepare for Transport
7.8. Close Transport LockUp Valve
7.9. Position Tractor Drawbar for Transport
7.10. Position Jack Stand for Transport
7.11. Check Leveling Adjustment
7.12. Transport Machine
7.13. Transport Implement Train
8. Operating Machine
8.1. General Guidelines for Use
8.2. Before Entering Field Guidelines
8.3. Field Operating Guidelines
8.4. Tighten Hardware
8.5. Use Operators Manual Holder
8.6. Operating Speed
8.7. Standards
8.8. Adjust CushionTrip Standard
8.9. Adjust FronttoRear Leveling
8.10. Proper Overlap
8.11. Adjust Single Point Depth Control
8.12. Field Depth Setting Procedure
8.13. Prepare to Operate in Field
8.14. Rephase Wing Depth CylindersFolding Machines
8.15. Level Wing Frames to Main FrameFolding Machines
8.16. Understand Active Hydraulic DownPressure Systems
8.17. Setting Rolling Baskets
8.18. Understand Active Hydraulic Rolling Basket DownPressure System
8.19. Adjust Rolling Basket DownPressureTractors With ElectroHydraulic Closed Center Systems
8.20. Adjust Rolling Basket DownPressureTractors With Mechanical SCV Controlled Closed Center Systems
8.21. Adjust Rolling Basket DownPressureTractors With Open Center Hydraulic Systems
8.22. Symptoms of Soil Compaction
8.23. Detect Compaction with John Deere Soil Probe
8.24. Soil Compaction Questions and Answers
9. Attachments
9.1. Adjustment Wrench
9.2. Disk Gang Tools
9.3. Closing Disk Spring Compression Tool
10. Lubricating
10.1. Lubricate and Maintain Machine Safely
10.2. Prevent Hydraulic System Contamination
10.3. Multipurpose Extreme Pressure (EP) Grease
10.4. Alternative and Synthetic Lubricants
10.5. Lubrication Symbols
10.6. Lubricant Storage
10.7. Perform Seasonal Lubrication
10.8. Lubricate Turnbuckle
10.9. Lubricate CushionTrip Standards
10.10. Lubricate Wheel Bearings
11. Troubleshooting
11.1. Verify Initial Settings
11.2. Machine Preparation Checklist
11.3. Troubleshooting Chart
11.4. Disk Blade and/or Disk Component Failure
11.5. Maximize Disk Gang Penetration
12. Servicing
12.1. Practice Safe Maintenance
12.2. Use Safe Service Procedures
12.3. Work in Clean Area
12.4. Service Machines Safely
12.5. Support Machine Properly
12.6. Avoid HighPressure Fluids
12.7. Replace Hydraulic Hoses
12.8. Sharpen Sweeps and Disks
12.9. Tighten Hardware
12.10. Metric Bolt and Screw Torque Values
12.11. Unified Inch Bolt and Screw Torque Values
12.12. Face Seal Fittings Assembly and InstallationAll Pressure Applications
12.13. Metric Face Seal and ORing Stud End Fitting Torque ChartStandard Pressures
12.14. SAE Face Seal and ORing Stud End Fitting Torque ChartStandard Pressures
12.15. Service Tires Safely
12.16. Check Tire Pressure
12.17. Discard Tires Properly
12.18. Repair Tire
12.19. Check Wheel HardwareAll Tillage Machines
12.20. Inspect Main Frame Wheel Module Bearings
12.21. Replace Main Frame Wheel Module Bearings
12.22. Inspect Wing Frame Wheel Module Bearings
12.23. Replace Wing Frame Wheel Module Bearings
12.24. Discard Waste Oil Properly
12.25. Prevent Hydraulic System Contamination
12.26. Check Depth Control Cylinders for Internal LeakageRigid Machines
12.27. Check Depth Control Cylinders for Internal LeakageFolding Machines
12.28. Analyze Test Results
12.29. Remove Hydraulic Cylinders
12.30. Bleed Hydraulic Cylinders
12.31. Replace Ripper Point
12.32. Replace Shank Wear Shin (If Equipped)
12.33. Replace ShankCushionTrip Standard
12.34. Tighten CushionTrip Standard UBolts
12.35. Tighten CSpring Standards
12.36. Replace Rolling Basket Split Tension Bushings
12.37. Tighten Rolling Basket Cap Screws
12.38. Service Single Disks
12.39. Verify Torque Specifications
12.40. Service Gangs
12.41. Gang Component Diagram
12.42. Assemble Gang Bolt Tensioner
12.43. Disassemble Gangs
12.44. Assemble Gangs
12.45. Identify Disk Blades Eligible for Warranty
12.46. Identify Disk Blades Not Eligible for Warranty
13. Storing
13.1. Remove Machine from Storage
13.2. Place Machine In Storage
14. Specifications
14.1. Tractor Power Recommendations
14.2. Hydraulic Requirements
14.3. Download Force on Tractor Drawbar
14.4. Hitch Specifications
14.5. Rigid Machine Specifications
14.6. Folding Machine Specifications
14.7. Eurasian Economic Union
14.8. EC Declaration of Conformity
14.9. CE Plate and EAC Label Locations
14.10. Machine Design Life
14.11. Record Product Identification Number (P.I.N.)
14.12. Keep Proof of Ownership
14.13. Keep Machines Secure
15. John Deere Service Keeps You On The Job
15.1. John Deere Parts
15.2. The Right Tools
15.3. WellTrained Technicians
15.4. Prompt Service

John Deere 2730 Combination Ripper Operator Manual OMKK60471

Description

Related products

Login